diff --git a/examples/APDS-9960_Multi-VL53L0X/APDS-9960_Multi-VL53L0X.ino b/examples/APDS-9960_Multi-VL53L0X/APDS-9960_Multi-VL53L0X.ino
index bbc482d..2ff8288 100644
--- a/examples/APDS-9960_Multi-VL53L0X/APDS-9960_Multi-VL53L0X.ino
+++ b/examples/APDS-9960_Multi-VL53L0X/APDS-9960_Multi-VL53L0X.ino
@@ -14,11 +14,12 @@
 #define SENSOR_CNT 5
 #define XSHUT_START_PIN 4 //we start with pin 4 because 2 and 3 are interrupt pins (on the nano)
 #define SENSORS_START_ADDRESS 45 //0x35 next sensor has 0x36, ...
-#define DISTANCE_THRESHOLD 75 //if object is closer than this millimeters an hit will be signaled
+#define DISTANCE_MAX_THRESHOLD 75 //if object is closer than this millimeters an hit will be signaled
+#define DISTANCE_MIN_THRESHOLD 10
 #define TIMING_BUDGET 50000
 #define TIMING_CONTINOUES 50
 #define TIMEOUT 100
-#define VL53L0X_DEBOUNCE 1500 //after a hit distance is messarued after this time of milliseconds again
+#define VL53L0X_DEBOUNCE 500 //after a hit distance is messarued after this time of milliseconds again
 VL53L0X sensors[SENSOR_CNT];
 unsigned long sensorsLastHit[SENSOR_CNT];
 
@@ -41,7 +42,7 @@ unsigned long sensorsLastHit[SENSOR_CNT];
 // prevent gesture sensor interrupt when just standing in front of mirror, this will
 // reduce infrared LED power:
 // if you use a third party sensor (not SPARKFUN) make sure to set the GGAIN value to GGAIN_1X
-// #define DEFAULT_GGAIN           GGAIN_2X // was: GGAIN_4X
+// #define DEFAULT_GGAIN           GGAIN_1X // was: GGAIN_4X
 // #define DEFAULT_GLDRIVE         LED_DRIVE_50MA // was: LED_DRIVE_100MA
 
 
@@ -80,7 +81,7 @@ void setup() {
   }
   
    // Initalisiert I2C
-  delay(500);
+  delay(200);
   Wire.begin();
   Wire.beginTransmission(0x29);
   
@@ -89,12 +90,12 @@ void setup() {
   for (int i = 0; i < SENSOR_CNT; i++)
   {
     digitalWrite(XSHUT_START_PIN + i,HIGH);
-    delay(500);
+    delay(50);
     sensors[i].init();
     Serial.print("VL53L0X");
     Serial.print(i);
     Serial.println(" - SetAdress");
-    delay(500);
+    delay(150);
     sensors[i].setAddress(SENSORS_START_ADDRESS+i);
     Serial.print("VL53L0X");
     Serial.print(i);
@@ -166,19 +167,20 @@ void loop() {
   {
     if ((curTime - sensorsLastHit[i]) > VL53L0X_DEBOUNCE){
       uint16_t curValue = sensors[i].readRangeContinuousMillimeters();
-      if (curValue <= DISTANCE_THRESHOLD){
+      if ((curValue > DISTANCE_MIN_THRESHOLD)&&(curValue <= DISTANCE_MAX_THRESHOLD)){
         Serial.print("VL53L0X");
         Serial.print(i);
         if (sensors[i].timeoutOccurred()) { 
           Serial.print(": TIMEOUT"); 
         } else {
-          Serial.print(": HIT");
+          Serial.print(": HIT -> ");
+          Serial.print(curValue);
           sensorsLastHit[i] = curTime;
         }
         Serial.println();
       } 
       
-      delay(200);
+      delay(100);
     }
   }  
   
diff --git a/examples/APDS-9960_Multi-VL53L1X/APDS-9960_Multi-VL53L1X.ino b/examples/APDS-9960_Multi-VL53L1X/APDS-9960_Multi-VL53L1X.ino
index fd29604..952d34c 100644
--- a/examples/APDS-9960_Multi-VL53L1X/APDS-9960_Multi-VL53L1X.ino
+++ b/examples/APDS-9960_Multi-VL53L1X/APDS-9960_Multi-VL53L1X.ino
@@ -14,7 +14,8 @@
 #define SENSOR_CNT 3
 #define XSHUT_START_PIN 4 //we start with pin 4 because 2 and 3 are interrupt pins (on the nano)
 #define SENSORS_START_ADDRESS 53 //0x35 next sensor has 0x36, ...
-#define DISTANCE_THRESHOLD 75 //if object is closer than this millimeters an hit will be signaled
+#define DISTANCE_MAX_THRESHOLD 100 //if object is closer than this millimeters an hit will be signaled
+#define DISTANCE_MIN_THRESHOLD 10
 #define DISTANCE_MODE VL53L1X::Long //the sensor supports Short, Mid, Long mode
 #define TIMING_BUDGET 50000
 #define TIMING_CONTINOUES 50
@@ -42,7 +43,7 @@ unsigned long sensorsLastHit[SENSOR_CNT];
 // prevent gesture sensor interrupt when just standing in front of mirror, this will
 // reduce infrared LED power:
 // if you use a third party sensor (not SPARKFUN) make sure to set the GGAIN value to GGAIN_1X
-// #define DEFAULT_GGAIN           GGAIN_2X // was: GGAIN_4X
+// #define DEFAULT_GGAIN           GGAIN_1X // was: GGAIN_4X
 // #define DEFAULT_GLDRIVE         LED_DRIVE_50MA // was: LED_DRIVE_100MA
 
 
@@ -81,7 +82,7 @@ void setup() {
   }
   
    // Initalisiert I2C
-  delay(500);
+  delay(200);
   Wire.begin();
   Wire.beginTransmission(0x29);
   
@@ -90,12 +91,12 @@ void setup() {
   for (int i = 0; i < SENSOR_CNT; i++)
   {
     digitalWrite(XSHUT_START_PIN + i,HIGH);
-    delay(500);
+    delay(50);
     sensors[i].init();
     Serial.print("VL53L1X");
     Serial.print(i);
     Serial.println(" - SetAdress");
-    delay(500);
+    delay(150);
     sensors[i].setAddress(SENSORS_START_ADDRESS+i);
     Serial.print("VL53L1X");
     Serial.print(i);
@@ -168,7 +169,7 @@ void loop() {
   {
     if ((curTime - sensorsLastHit[i]) > VL53L1X_DEBOUNCE){
       int curValue = sensors[i].read(true);
-      if (curValue <= DISTANCE_THRESHOLD){
+      if ((curValue > DISTANCE_MIN_THRESHOLD)&&(curValue <= DISTANCE_MAX_THRESHOLD)){
         Serial.print("VL53L1X");
         Serial.print(i);
         if (sensors[i].timeoutOccurred()) { 
@@ -180,7 +181,7 @@ void loop() {
         Serial.println();
       } 
       
-      delay(200);
+      delay(100);
     }
   }  
   
diff --git a/node_helper.js b/node_helper.js
index 7be98f1..7c1963a 100644
--- a/node_helper.js
+++ b/node_helper.js
@@ -50,7 +50,7 @@ module.exports = NodeHelper.create({
     for(var curExptMessage in self.config.devices[curDev].messages){
       if(curData.indexOf(curExptMessage) == 0){
         for(var curNotification in self.config.devices[curDev].messages[curExptMessage]){
-          console.log(self.currentProfilePattern.toString())
+          // console.log(self.currentProfilePattern.toString())
           if(typeof self.config.devices[curDev].messages[curExptMessage][curNotification].profiles === 'undefined' || 
             self.currentProfilePattern.test(self.config.devices[curDev].messages[curExptMessage][curNotification].profiles)){
             if(typeof self.config.devices[curDev].messages[curExptMessage][curNotification].notification !== 'undefined'){
diff --git a/package.json b/package.json
index 05ddae5..8551e54 100644
--- a/package.json
+++ b/package.json
@@ -1,15 +1,16 @@
 {
   "name": "MMM-Serial-Notifications",
-  "version": "0.0.3",
+  "version": "0.0.4",
   "description": "",
   "main": "MMM-Serial-Notifications.js",
   "devDependencies": {},
   "scripts": {
-    "postinstall": "node_modules/.bin/electron-rebuild -e ../../node_modules/electron"
+    "postinstall": "node_modules/.bin/MagicMirror-rebuild"
   },
   "dependencies": {
     "serialport": "latest",
-    "electron-rebuild": "^1.2.1"
+    "electron-rebuild": "latest",
+    "magicmirror-rebuild": "latest"
   },
   "repository": {
     "type": "git",