Skip to content

Latest commit

 

History

History
217 lines (160 loc) · 10.4 KB

README.md

File metadata and controls

217 lines (160 loc) · 10.4 KB
Raw

esp32_beo4

Library for Bang & Olufsen Beo4 remote control, using a TSOP7000 IR receiver and a ESP32

1. Examples

1.1 Example with beo4_task

It turned out that the callback function is suitable to just print the codes, but time consuming usages will lead to disturbances of the receiver task. So the queue based beo4_task alternative is the recommended solution, like so:

#include <Arduino.h>
#include "IrBeo4.h"

#define IR_RX_PIN 34            // IR receive pin
IrBeo4 beo4(IR_RX_PIN);         // instance

xQueueHandle beo4_rx_queue;     // queue 
TaskHandle_t beo4_task_h;       // task handle

void beo4_task(void *parameter) {
  static uint32_t beo4Code=0;
  while(1) {
    if(pdTRUE==xQueueReceive(beo4_rx_queue,(void*)(&beo4Code),portMAX_DELAY)) {
      Serial.printf("beo4_task:   %04x %s %s\n",
                    beo4Code,
                    beo_src_tbl(beo4Code),
                    beo_cmd_tbl(beo4Code));
    }
  }
}


void setup() {
  Serial.begin(115200);
  beo4_rx_queue = xQueueCreate(50, sizeof(uint32_t));
  xTaskCreatePinnedToCore(beo4_task,"beo4_task",10000,NULL,0,&beo4_task_h,0);
  beo4.Begin(beo4_rx_queue);
  printf("beo4 started, RX=%d\n",IR_RX_PIN);
}

void loop() {
}

1.2 Home Assistant MQTT auto discovery example

Using the MQTT auto discovery feature for Home Assistant integration Details see --> https://github.com/aanban/esp32_beo4/tree/main/examples/esp32_beo4_HA/readme.md

06_noise_pulse

2. TSOP7000 Issues

The Bang & Olufsen IR remote control Beo4 works with a carrier frequency of 455kHz. A suitable decoder device is the TSOP7000 from Vishay. However, the production has been stopped in 2009 . Replicas appeared a few years ago , but unfortunately they do not work the same way and have bad habits producing dummy pulses and having hiccups sometimes.

The tsop7000 replicas, that I have tested, in principle decodes a low-activ pulse from a 455kHz carrier burst, as expected. The Beo4 carrier bursts have a length of 200μs, i.e. after the 200μs low pulse the ir_raw signal should toggle and stay at high-level to indicate the pause. But my tested replicas do have this bad habit of not switching to high in a proper manner. The picture below shows the dummy pulses that occur sporadically after 200μs. (blue = TSOP7000 output signal).

Another issue is that the tested TSOP7000 are quite sensitive and react to sunlight or whatever, anyway I observed sporadic pulses on the output even without pressing any button on the Beo4 remote control.

06_noise_pulse

2.1. Approach to avoid the dummy pulses

The low pulses are not important for decoding the received signal, i.e. only the total length (falling edge --> falling edge) is important.

Note

The PulseWidth is measured as time between two falling edges and converted to PulseCodes.
PulseWidth[µs] = tnew_edge - tprevious_edge

The low pulses can therefore also be extended in order to suppress the interference pulses. I have tested two work arrounds, a hardware-based monoflop approach and a software-based debouncing solution.

2.1.1. Hardware work arround

In terms of hardware, a monoflop can suppress the interference pulses. The following circuit with a TLC555 has worked. The low pulse is extended to ca. 620µs. The output signal ir_out is high-active, therefore mode=RISING must be set in the attachInterrupt() function instead of mode=FALLING.

d

2.1.2. Software solution

The software-based work-arround is easier to implement. Debouncing (similar to debouncing of buttons) is implemented within the interrupt service routine. Timestamps are measured for each interrupt and compared with the previous interrupt. The timestamp is put into the g_isr_queue queue only, if the previous interrupt was more than t_debounce=600µs ago, i.e. the short interference pulses will be suppressed.

// interrupt service routine
void IRAM_ATTR ir_pulse_isr(void) {
  static int64_t tsPre=0;              // timestamp of previous edge
  int64_t tsNew=esp_timer_get_time();  // timestamp of new edge
  if((tsNew-tsPre) > t_debounce ) {    // debounce TSOP7000 output
    xQueueSend(g_isr_queue,&tsNew,0);  // send timestamp to queue if valid low pulse
    tsPre=tsNew;
  }
}

The TSOP7000 output is low-activ, therefor mode=FALLING must be set in the attachInterrupt() function.

  // attach interrupt to TSOP7000 output, and set to falling edge
  if(-1!=m_rx_pin) { 
    pinMode(m_rx_pin, INPUT);
    attachInterrupt(m_rx_pin, ir_pulse_isr, FALLING);
  }

3. Decoding B&O Beo4 remote control codes

Further information about the Beo4 remote control code-format can be found here:

Comment Link
data-link manual https://www.mikrocontroller.net/attachment/33137/datalink.pdf
Beomote https://github.com/christianlykke9/Beomote

3.1. Mapping PulseWidth to PulseCode

Pulses have different widths and corresponding PulseCodes as seen in the table below.

Note

The different pulse-widths are multiples of 3125us, i.e. the PulseCode can be calculated this way:
PulseCode = (tnew_edge - tprevious_edge + 1562) / 3125

PulseWidth PulseCode define Comment
3125 µs 1 BEO_ZERO bit = 0
6250 µs 2 BEO_SAME bit = same as previous bit
9375 µs 3 BEO_ONE bit = 1
12500 µs 4 BEO_STOP stop-code
15625 µs 5 BEO_START start-code

The picture below shows the frame start with two short pulses and long pulse, that results in a PulseCode sequence BEO_ZERO,BEO_ZERO, BEO_START

02_beo_start_pulse

3.2. Decoding Beo4 PulseCode sequences

The Beo4 remote control generates the PulseCode sequences with a total length of 21 pulses as seen below

00_beo_frame

A complete Beo4 frame with 21 PulseCodes consists of the start-sequence BEO_ZERO , BEO_ZERO , BEO_START, followed by the 17 payload data codes each in the range [BEO_ZERO , BEO_SAME , BEO_ONE] and ends with the BEO_STOP code.

Within the payload data the PulseCodes are mapped to BitCodes as followed:

PulseCode     BitCode
---------     ----------
BEO_ZERO  --> BitCode=0 
BEO_ONE   --> BitCode=1 
BEO_SAME  --> BitCode=previous BitCode

Note

The BEO_SAME code was probably introduced to get approximately the same frame length for all Beo4 buttons. Otherwise, Beo4 commands with many 0-data-bits (e.g. TV-0 button) would become much shorter than those with many 1-data-bits. BEO_ZERO consumes 3.2ms and BEO_ONE consumes 9.3ms.

The 17 Bit payload is devided into 3 data fields beoLink (1-Bit), beoSource (8-Bit) , and beoCommand (8-Bit). The beoSource indicates the device, e.g Audio , Video , Light and so on. The beoCommand indicates the current button, e.g. 0 , left, right, volume ++ and so on.

//            _   ___________________   ____________
// ir_raw      |_|                   |_|
//              ___                   ___
// ir_out     _|   |_________________|   |__________
//
//             |<----PulseWidth----->|
//
//            Start      Data                                               Stop  
// ir_out     |_|_|_____|_|__|__|__|___|__|_|___|__|_|__|__|__|___|_|__|___|____|
// PulseCodes  1 1 5     1 2  2  2  3   2  1 3   2  1 2  2  2  3   1 2  3   4
// BitCodes              0 0  0  0  1   1  0 1   1  0 0  0  0  1   0 0  1   
// Payload     beoLink__/  |<---beoSource------->|  |<---beoCommand---->|
//                               
// BeoCode    = 0 00011011 00001001 = 0x01B09 
// beoLink    = 0
// beoSource  = 0x1B = LIGHT
// beoCommand = 0x09 = 9
//

Note

It turned out that the decoded data field beoLink is always=0 for all buttons I tested with the Beo4 remote control. Well, this information can be skipped so that a complete BeoCode fits into two bytes.

3.2.1. Example of the "TV on" button

Start beoLink beoSource beoCommand Stop
PulseCode 115 1 2222 2222 3122 2222 4
BitCode 0 0000 0000 1000 0000
beoCode 0 0x00 0x80 
   beoCode     = 0x0080          
   beoLink     = 0               
   beoSource   = 0x00 --> video  
   beoCommand  = 0x80 --> TV     
   Button      = TV on

3.2.2. Example of the "LIGHT - #9" button

Start beoLink beoSource beoCommand Stop
PulseCode 115 1 2223 2132 1222 3123 4
BitCode 0 0001 1011 0000 1001
beoCoode 0 0x1B 0x09 
   beoCode     = 0x1B09          
   beoLink     = 0               
   beoSource   = 0x1B -->  LIGHT 
   beoCommand  = 0x09 -->  9     
   Button      = LIGHT / 9

Note

During my tests with the Beo4 remote and the TSOP7000 hiccups I noticed that the Light button behaves quite special. I got valid frames without having touched the Beo4-remote at all. Once the Light button is pressed, after a minute or so the Beo4-remote automatically jumps back to the mode, that has been active before, e.g. Radio, TV and so on. In that case the following frame is send: beoSource=0x1B=Light and beoCommand=0x58=list