This list is a collection of the IKEA TRÅDFRI products, and their relevant technical properties. Please help me to update this list.
Always work safe: never work on a mains-powered product when it is still plugged in. I cannot be held liable for incomplete or inaccurate information, or any damage to yourself or your products.
IKEA has following products and product categories for the Smart Home series (also called TRADFRI):
- Smart Home Gateway
- FLOALT (light panel)
- GUNNARP (ceiling/wall lamp)
- LEPTITER (spotlight)
- IRSTA (worktop lighting)
- OMLOPP (spotlight)
- STRÖMLINJE (worktop lighting)
- SKYDRAG (worktop lighting)
- FYRTUR / KADRYL (window blinds)
- 5-button remote control (V1 and V2)
- 2-button dimmer/switch
- Wheel dimmer
- Shortcut button
- Motion detector (V1 and V2)
- Signal repeater + battery charger
- Switching outlet plug/mains
- LED driver 10 W with 3 connections
- LED Driver 30 W
- Bulb E27 1000 lm white/warmwhite
- Bulb E27 800 lm warmwhite
- Bulb E27 800 lm white/warmwhite transparent
- Bulb E27 600 lm color
- Bulb E14 600 lm color
- Bulb E14 600 lm white/warmwhite
- Bulb E27 250 lm filament gold
- Bulb GU10 400 lm warmwhite
- Bulb GU10 400 lm white/warmwhite
- Bulb GU10 350 lm color
Details:
- Socket: E27
- Potted: likely
Details:
- Socket: E27
- Potted: likely
Details:
- Socket: E27
- Potted: likely
Details:
- Socket: E27
- Potted: likely
Details:
- Socket: E27
- Potted: likely
Details:
- Socket: E14
- Potted: likely
Details:
- Socket: GU10
- Potted: yes
Teardown:
The potting material can be easily removed. It does not stick and will crumble in smaller peaces once you remove it.
Bulb pinout:
- 1: Common (+ max 28.4V @ 100%)
- 2: Warm leds (-)
- 3: Cold leds (-)
GU10 LED.
Details:
- Socket: GU10
- Potted: no
- TRÅDFRI Module: ICC-1
Teardown:
Use a small flat screw driver to lift up the plastic lens.
TRÅDFRI Module pinout:
- PA1 -> unused (but soldered)
- PB13 -> LED driver
Power usage:
| Brightness | Power (W) | Cos φ |
|---|---|---|
| 100% | 6.0 | 0.80 |
| 50% | 1.6 | 0.62 |
| 10% | 0.7 | 0.40 |
| Off | 0.0 | 1.00 |
Measured using a Voltcraft 3000 energy monitor.
GU10 LED. This seems to be the successor of the LED1650R5.
Details:
- Socket: GU10
- Potted: no
- Glued: yes (lens cover)
- TRÅDFRI Module: ICC-A-1
Teardown:
Use a hot air gun to soften the glue that holds the lens to the glass body. Make sure that you heat it up evenly, otherwise the glass will crack. Then use a small blade to lift up the lens (which has small hooks as well).
You can also heat it up in an oven to heat it up evenly. I tried 150 degrees Celsius with success.
The LED PCB can be removed by removing the two screws and lifting it up with a square hook or similar. The heatspreader is glued with white glue (thermal paste?) to the glass housing. I removed it by re-inserting the screw and then lifting it with pliers. Do this carefully, or you might cut yourself (been there, done that).
The PCB is press-fitted into the GU10 pins. To remove the whole PCB, use a side cutter and carefully clamp perpendicular to the dots on the GU10 pins (don't try to cut them!). A little pressure makes it then possible to lift the PCB from the GU10 pins.
TRÅDFRI Module pinout:
- PB13 -> LED driver
GU10 RGB spot.
Details:
- Socket: GU10
- Potted: no
- Glued: yes (lens cover)
- TRÅDFRI Module: MGM210L22F
- Rated: 345 lm, 4.6 W
Teardown:
See LED1837R5.
TRÅDFRI Module pinout:
- PA3 -> ?
- PC2 -> White channel (PWM1)
- PC3 -> Red channel (PWM2)
- PC4 -> Green channel (PWM3)
- PC5 -> Blue channel (PWM4)
Power usage:
| Brightness | Color | Power (W) | Cos φ |
|---|---|---|---|
| 100% | Cool White | 2.4 | 0.60 |
| 50% | Cool White | 0.4 | 0.25 |
| 10% | Cool White | 0.3 | 0.20 |
| Off | Cool White | 0.0 | 1.00 |
Measured using a Voltcraft 3000 energy monitor.
Remote controller.
TRÅDFRI Module pinout:
- PB15 -> Color temperature
- PB14 -> Dim -
- PC10 -> On/Off
- PB13 -> TX
- PA1 -> Dim +
- PA0 -> TouchLink button
Motion Sensor.
Details:
- Battery: 2x CR2032
Teardown:
The module is easy to take apart, and debug wires can be soldered on without separating the radio / MCU PCB from the carrier PCB. The carrier board is labelled "D-Sensor-A1-01-A-V2.0".
TRÅDFRI Module:
| Module Pin | Signal |
|---|---|
| PA0 | Switch Input |
| PA1 | Timer Input (Voltage Divider) |
| PB12 | Nothing? Has a capacitor position |
| PB13 | Photoresistor Analog |
| PB14 | PIR Interrupt |
| PB15 | Day/Night Analog |
| PC10 | PIR Serial Connection |
| Test Point | Signal |
|---|---|
| TP1_X | Day/Night Potentiometer Analog |
| TP2_X | Photoresistor Analog Output |
| TP3_X | Ground |
| TP4_X | Switch Output |
| TP5_X | Timer Potentiometer Analog |
| TP7_X | LED |
| TP8_X | Power Supply |
- Time selection dial (R13): PA1 (Looks like a potentiometer between R12 high side and a FET to GND enabled directly by PB14.)
- Day/night selection dial (R15): PB15 (Dito, with resistor R14 and same transistor.)
- Pairing button (S1): Silicone rubber button puling PA0 directly to GND
The motion detection dome is connected (one pin directly, one indirectly) to an "E93196C 5090C 9A" labelled 8-pin chip to which also PC10 and PB14 are connected (needs further investigation).
Motion sensor.
Details:
- Battery: 2x CR2032
Teardown:
Module is easy to take apart with the right tools, debug wires could be soldered on without separating the radio from the carrier PCB. The carrier board is labelled "D-SS-X2-01-A-V2.1" and the date printed is 2018-06-05. Tradfri module markings visible are Draco1.0_105° and 0255C.
TRÅDFRI Module (unverified):
- tK1 -> Day/Night selection button
- tK2 -> Pairing button
- tK3 -> Time selection button
The motion detection dome is connected (one pin directly, one indirectly) to an "E93196B 0940A 60A" labelled 8-pin chip. This appears to be Elmos E931.96.
- Various test points:
- VCC:
VDD - GND:
GND - Pairing BTN:
tK2 - Day/Night BTN:
tK1 - Time Select BTN:
tK3 - ???:
AL - ???:
ENT - ???:
TX1
- VCC:
Ethernet gateway.
Details:
- Power supply: USB 5V 1A
Protocol:
An overview of the COAP protocol used by the gateway can be found here.
Wireless dimmer.
Teardown:
Pinout:
- A0 - LED ON - TP7
- A1 - BTN - TP6
- B11 - FLASH CS
- B12 - GYRO INT
- B13 - FLASH VCC
- B14 - ACC INT - TP8
- B15 - GYRO ON - TP9
- C10 - I2C SDA
- C11 - I2C SCL
- D13 - FLASH MCLK
- D14 - FLASH MISO
- D15 - FLASH MOSI
- F0 - SWCLK - TP1
- F1 - SWDIO - TP2
- F2 - SWO - TP3
- F3 - DBG - TP4
-
RESET - TP5
LED output controller/dimmer
Details:
- Potted: no
The output appears to be measured by the module somehow.
Teardown:
TRÅDFRI Module pinout (incomplete/unverified):
- PA0: K1 (Reset key)
- PA1: Goes to ZD1, through R9 and then to OUT+, possibly output measuring?
- PB13: Pulls down the FET Gate
- PF0: Pin 2 on header
- PF1: Pin 3 on header
10 Watt Power supply with the 24 V output being controlled by ICPSLC24-10NA.
Teardown:
30 Watt Power supply with the 24 V output being controlled by ICPSLC24-10NA.
Teardown:
FLOALT 60x60
Details:
- Potted: no
TRÅDFRI Module pinout (incomplete):
- PA0: Pulse (not very readable)
- PA1: PWM3 (not very readable)
- PB1: PWM2
- PB13: PWM1