The “redirect” is a fundamental part of the HTTP protocol. The concept was present and is documented already in the first spec (RFC 1945), published in 1996, and it has remained well-used ever since.
A redirect is exactly what it sounds like. It is the server sending back an instruction to the client instead of giving back the contents the client wanted. The server basically says “go look over here instead for that thing you asked for“.
Redirects are not all alike. How permanent is the redirect? What request method should the client use in the next request?
All redirects also need to send back a Location: header with the new URI to
ask for, which can be absolute or relative.
Is the redirect meant to last or just remain valid for now? If you want a GET to permanently redirect users to resource B with another GET, send back a 301. It also means that the user-agent (browser) is meant to cache this and keep going to the new URI from now on when the original URI is requested.
The temporary alternative is 302. Right now the server wants the client to send a GET request to B, but it should not cache this but keep trying the original URI when directed to it next time.
Note that both 301 and 302 will make browsers do a GET in the next request, which possibly means changing the method if it started with a POST (and only if POST). This changing of the HTTP method to GET for 301 and 302 responses is said to be “for historical reasons”, but that’s still what browsers do so most of the public web will behave this way.
In practice, the 303 code is similar to 302. It will not be cached and it will make the client issue a GET in the next request. The differences between a 302 and 303 are subtle, but 303 seems to be more designed for an “indirect response” to the original request rather than just a redirect.
These three codes were the only redirect codes in the HTTP/1.0 spec.
curl however, does not remember or cache any redirects at all so to it, there's really no difference between permanent and temporary redirects.
In curl's tradition of only doing the basics unless you tell it differently,
it does not follow HTTP redirects by default. Use the -L, --location to tell
it to do that.
When following redirects is enabled, curl will follow up to 50 redirects by
default. There's a maximum limit mostly to avoid the risk of getting caught in
endless loops. If 50 is not sufficient for you, you can change the maximum
number of redirects to follow with the --max-redirs option.
All three of these response codes, 301 and 302/303, will assume that the client sends a GET to get the new URI, even if the client might have sent a POST in the first request. This is important, at least if you do something that does not use GET.
If the server instead wants to redirect the client to a new URI and wants it to send the same method in the second request as it did in the first, like if it first sent POST it’d like it to send POST again in the next request, the server would use different response codes.
To tell the client “the URI you sent a POST to, is permanently redirected to B where you should instead send your POST now and in the future”, the server responds with a 308. And to complicate matters, the 308 code is only recently defined (the spec was published in June 2014) so older clients may not treat it correctly! If so, then the only response code left for you is…
The (older) response code to tell a client to send a POST also in the next request but temporarily is 307. This redirect will not be cached by the client though, so it’ll again post to A if requested to again. The 307 code was introduced in HTTP/1.1.
Oh, and redirects work the same same way in HTTP/2 as they do in HTTP/1.1.
| Permanent | Temporary | |
|---|---|---|
| Switch to GET | 301 | 302 and 303 |
| Keep original method | 308 | 307 |
It turns out that there are web services out there in the world that want a POST sent to the original URL, but are responding with HTTP redirects that use a 301, 302 or 303 response codes and still want the HTTP client to send the next request as a POST. As explained above, browsers won’t do that and neither will curl—by default.
Since these setups exist, and they’re actually not terribly rare, curl offers options to alter its behavior.
You can tell curl to not change the non-GET request method to GET after a 30x
response by using the dedicated options for that: --post301, --post302 and
--post303. If you are instead writing a libcurl based application, you
control that behavior with the CURLOPT_POSTREDIR option.
When you use curl you may provide credentials like user name and password for a particular site, but since a HTTP redirect might move away to a different host curl limits what it sends away to other hosts than the original within the same "transfer".
So if you want the credentials to also get sent to the following host names
even though they are not the same as the original—presumably because you
trust them and know that there's no harm in doing that—you can tell curl that
it is fine to do so by using the --location-trusted option.
Browsers support more ways to do redirects that sometimes make life complicated to a curl user as these methods are not supported or recognized by curl.
If the above was not enough, the web world also provides a method to redirect
browsers by plain HTML. See the example <meta> tag below. This is somewhat
complicated with curl since curl never parses HTML and thus has no knowledge
of these kinds of redirects.
<meta http-equiv="refresh" content="0; url=http://example.com/">
The modern web is full of JavaScript and as you know, JavaScript is a language and a full run time that allows code to execute in the browser when visiting web sites.
JavaScript also provides means for it to instruct the browser to move on to another site—a redirect, if you will.