SMA und EVCC update fehler #15744
Replies: 14 comments 13 replies
-
Siehe #15590. Auf welchem System läuft evcc bei Dir? Config? |
Beta Was this translation helpful? Give feedback.
-
Raspberry Pi... `meters:
chargers:
vehicles:
loadpoints:
tariffs: site: |
Beta Was this translation helpful? Give feedback.
-
Bei läuft es seit dem ich in der yaml interface: eth0 Auskommentiert habe mit # beim SHM |
Beta Was this translation helpful? Give feedback.
-
Habe das Interafce mal auskommentiert Was läuft den genau damit? Meinst du die Fehlermeldung? Den verbrauch zeigt er mir leider immer noch nicht an :( |
Beta Was this translation helpful? Give feedback.
-
Ich meine damit, das evcc mit der Version 0.130.6 und der Auskommentierung fehlerfrei startet und die Fehlermeldung nicht auftritt. |
Beta Was this translation helpful? Give feedback.
-
Wie macht man das? Seit dem SMA das Speedwire update drauf gehauen hat, bekomme ich lockal keine Daten mehr vom WR :( |
Beta Was this translation helpful? Give feedback.
-
habe den SUNNY TRIPOWER 10.0 mit SHM2.0 :( Habe alles direkt an der Fritzbox angeschlossen, weil mein Switch kein IGMP v3 kann. Hatte gelesen dass es helfen soll :( Ich Probier das mit dem Modbus aus jetzt... mfg EDIT: Muss man im SunnyPortal Modbus aktivieren? Also im lokalen WR steht das Modbus aktiviert ist mit port 502 Also er liest die Verbrauchsdaten immer noch nicht ab :( |
Beta Was this translation helpful? Give feedback.
-
ich habe ebenfalls seit kurzem das Problem, dann In = Out ist. An der EVCC Version liegt es nicht. Habe einige probiert. Config sieht wie folgt aus:
chargers:
vehicles:
loadpoints:
tariffs: site: mqtt: hems: |
Beta Was this translation helpful? Give feedback.
-
Ja exakt das selbe Problem habe ich auch |
Beta Was this translation helpful? Give feedback.
-
Hi zusammen, ich habe ein sehr ähnliches Problem. Vielleicht findet jemand noch den Fehler. |
Beta Was this translation helpful? Give feedback.
-
Aus reiner Neugierde - habt ihr das Problem mit den falschen Werten immer oder nur ab und zu? Ist das Problem nach einem Downgrade auf evcc Version 0.129.0 immer noch vorhanden? |
Beta Was this translation helpful? Give feedback.
-
Bei mir trat das Problem plötzlich, ohne eine Update, auf. Es ist immer da. Ich hatte hier ein Issue erstellt (#15809). Es wurde noch nicht freigegeben da meine Logs noch fehlten. Habe diese ergänzt und warte seit 4 Tagen auf die Freigabe. |
Beta Was this translation helpful? Give feedback.
-
Welche FW-Version hat denn der SMA-Wechselrichter? Irgendwo anders hatte ich einen Hinweis gelesen, dass nach einem FW-Update von SMA im Mai die Modbus-Register nicht mehr geändert werden konnten (oder so ähnlich). Muss mal auf die Suche gehen... |
Beta Was this translation helpful? Give feedback.
-
Hier auch ein Teil meiner LOGs [lp-1 ] DEBUG 2024/09/08 11:24:25 charge power: 0W |
Beta Was this translation helpful? Give feedback.
-
Hallo,
bekomme seit einiger Zeit keine Daten mehr aus dem SMA Wechselrichter ( EVCC zeigt nur erzeugnis an und kein Verbrauch mehr ), hatte mich damit schon irgendwie abgefunden.
Nach dem ich EVCC heute mal auf die neueste Version aktualisiert habe, startete EVCC nicht mit folgendem Fehler:
cannot create meter 'pv2': cannot create meter type 'template': cannot create meter type 'sma': failed to get device: no Speedwire ping response for 192.168.2.29
Was ja nicht sein kann... Kann ja ohne probleme drauf und wenn ich EVCC neu starte geht es halbwegs wieder :(
Hat jemand das selbe Problem?
mfg
Beta Was this translation helpful? Give feedback.
All reactions