PV laden 2min an, 2min aus, … #16653
Replies: 12 comments 13 replies
-
Kann deine Keba UDP? |
Beta Was this translation helpful? Give feedback.
-
Hast du eine alte Doku zu dem Template. Würde ich einfach mal ausprobieren. Die Keba ist eine B-Series. Daher kein Modbus. |
Beta Was this translation helpful? Give feedback.
-
Dann bleibt nur die Lösung über die Freigabe. Habt ihr eine Idee wie ich das in den Griff bekommen, dass evcc ständig ein und aus schaltet? |
Beta Was this translation helpful? Give feedback.
-
Moin, @VolkerK62: Ja die Wallbox ist per Dippschalter auf 13A gestellt. Im evcc auch: @0x3d13f : Shelly als Smartmeter: das läßt sich leider (bitte korrigiert mich) nicht verhindert bei dem Shelly Template. @VolkerK62 : Ne Standbypower ist 0.7 😄 (Koppelrelay zieht ca. 1W) Die Leistung der Wallbox hätte ich im iobroker über ein ZWave Qubinio. Wenn ich die irgendwie in das evcc bekomme und dann der Wallbox (Shelly) zuordnen könnte wäre das die Lösung. Klar hier die Config: `'# open evcc at http://evcc.local:7070 log: debug '# unique installation id interval: 30s # control cycle interval meters:
chargers:
loadpoints:
site:
|
Beta Was this translation helpful? Give feedback.
-
So ca. 11:30 bis 13:30Uhr war das ein/aus |
Beta Was this translation helpful? Give feedback.
-
Da hast du recht. Ich habe den Min Ladestrom erst danach von 6A auf 13A geändert weil ihr es hier geschrieben habt. |
Beta Was this translation helpful? Give feedback.
-
Und ich habe jetzt mal das Ein/Aus etwas geändert. Da meine PV Anlage ja auch recht klein ist mit 5,1kwp habe ich aus der Doku mal folgendes eingefügt: loadpoints:
|
Beta Was this translation helpful? Give feedback.
-
Kannst Du den SHM dierkt aufrufen (zB. Fritzbox) ? |
Beta Was this translation helpful? Give feedback.
-
In der Fritzbox kann ich Pingen, aber evcc meldet: wie komme ich ggf auf Modbus an dieser Stelle? |
Beta Was this translation helpful? Give feedback.
-
Danke, ich atte keine Idee wo nach ich suchen soll. |
Beta Was this translation helpful? Give feedback.
-
@VolkerK62 sage mal kann ich einen Shelly Pro 3em vor die Wallbox setzen und im Loadpoint mit der Wallbox verheiraten, damit ich dann die Leistung der Wallbox auch wirklich messe. Momentan krieg ich a ja nur die "1Watt" vom shellyplug für die Freigabe, die man nicht abstellen kann. |
Beta Was this translation helpful? Give feedback.
-
@ VolkerK62 |
Beta Was this translation helpful? Give feedback.
-
Moin,
Konfigurationsüberblick:
SMA Wechselrichter mit HM2.0
SMA SB2.5 mit BYD Batterie
KEBA Wallbox ohne Modbus Freigabe über Shelly Plug
Einstellungen:
Primo Hausbatterie: 30%
Batt unterstützen laden ab 90%
Heute war das Auto zum ersten mal leer und es gab Sonne. Und schon hab ich Probleme mit meiner Konfiguration.
Batterie wird bis 30% geladen. Dann startet das Laden des Autos. 2 Minuten an, dann wieder aus usw. bis die Batterie voll ist dann wird „normal“ geladen.
Ich denke es hängt mit meinem Ladepunkt zusammen. Leider kann meine Kebabox kein Modbus. Also wird sie über eine externe Freigabe (Koppelrelais) von einem Shelly Plug gestartet. Beim Laden über Zeitplan oder über dyn. Stromtarif klappt das super.
Allerdings liefert der Shelly Plug eine Leistung von 1W zurück. Ich denke damit kommt alles durcheinander weil geladen wird mit 13 A.
Hat jemand eine Idee wie ich meine Konfiguration optimieren kann?
Grüße
Björn
Beta Was this translation helpful? Give feedback.
All reactions