slic3r_ffcp_octo.ini

# generated by Slic3r 1.2.9 on Fri Jun 23 17:51:59 2017

[filament:ABS]
bed_temperature = 110
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #80FF80
filament_diameter = 1.75
first_layer_bed_temperature = 120
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 225

[filament:PETG]
bed_temperature = 80
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 80
first_layer_temperature = 250
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 245

[filament:PLA]
bed_temperature = 60
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 65
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 225

[presets]
filament = PLA.ini
filament_1 = PLA
print = 0.3mm no support.ini
printer = FFCPro Left.ini

[print:0.3mm brim+support]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 2
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:0.3mm no support]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[printer:FFCPro Dual]
bed_shape = -114x-75,112x-75,112x75,-114x75
before_layer_gcode = ; layer [layer_num]
end_gcode = M73 P100 ; end build progress\nG162 X Y F2500; home X and Y axes\nM109 S0 T0; set bed temperature to 0\nM104 S0 T0; set 1st extruder temperature to 0\nM104 S0 T1; set 2nd extruder temperature to 0\nG0 Z150; lower Z axis to bottom\nM18; disable all stepper motors\nM70 P5; We <3 Making Things!\nM72 P1; Play Ta-Da song
extruder_offset = 0x0,0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = PASTE_HERE
octoprint_host = greenpi.local
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 0,0
retract_length = 2,2
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
start_gcode = ; begin\nM73 P0 ; tell the firmware we're starting a build\nG130 X118 Y118 Z40 A118 B118  ; set vref's to default\n;\n; set temps\nM140 S[first_layer_bed_temperature] ; set bed temp, don't wait\nM104 S[first_layer_temperature_0] T0 ; set nozzle temp, don't wait\nM104 S[first_layer_temperature_1] T1 ; set nozzle temp, don't wait\n;\n; home and set coordinates\n\nT0 ; home on the right extruder\nG90 ;  set positioning to absolute\nG28 X Y Z ; home XYZ at default home feedrates\n; home Z again slowly to give more consistent first layer height\nG92 X0 Y0 Z0 A0 B0 ; define this as Z=0, the other coords are technically unnecessary but x3g requires them so gpx will make some up\nG1 Z5 ; move the platform 5mm down\nG28 Z F500 ; so we can home z again slowly\nM132 X Y Z  ; Recall stored home offsets\n;\n; wait for heat up\nG1 X112 Y-72 Z30 F3300 ; move to waiting position (front right corner of print bed)\nM116 ; wait for target temperatures to be reached. GPX only, RepG doesn't understand\n\n; purge and wipe left extruder\nT1;\nG92 E0 ; set current extruder position as 0 so that E15 below makes sense\nG1 X110 Y-70 Z[first_layer_height] F2400.0 ; move to just on the bed\nG1 X110 Y70 E15 F1200.000 ; extrude a line of filament along the right edge of the bed\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0\n\n; purge and wipe right extruder\nT0;\nG92 E0 ; set current extruder position as 0 so that E15 below makes sense\nG1 X105 Y-70 Z[first_layer_height] F2400.0 ; move to just on the bed\nG1 X105 Y70 E15 F1200.000 ; extrude a line of filament along the right edge of the bed\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0
toolchange_gcode = T[next_extruder]
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[printer:FFCPro Left]
bed_shape = -114x-75,112x-75,112x75,-114x75
before_layer_gcode = ; layer [layer_num]
end_gcode = M73 P100 ; end build progress\nG162 X Y F2500; home X and Y axes\nG0 Z150; lower Z axis to bottom\nM18; disable all stepper motors\nM109 S0 T0; set bed temperature to 0\nM104 S0 T1; set extruder temperature to 0\nM70 P5; We <3 Making Things!\nM72 P1; Play Ta-Da song
extruder_offset = 0x0,0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = PASTE_HERE
octoprint_host = greenpi.local
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 0,0
retract_length = 2,2
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
start_gcode = ; begin\nM73 P0 ; tell the firmware we're starting a build\nG130 X118 Y118 Z40 A118 B118  ; set vref's to default\n;\n; set temps\nM140 S[first_layer_bed_temperature] ; set bed temp, don't wait\nM104 S[first_layer_temperature_1] T1 ; set nozzle temp, don't wait\n;\n; home and set coordinates\n\nT0 ; home on the right extruder\nG90 ;  set positioning to absolute\nG28 X Y Z ; home XYZ at default home feedrates\n; home Z again slowly to give more consistent first layer height\nG92 X0 Y0 Z0 A0 B0 ; define this as Z=0, the other coords are technically unnecessary but x3g requires them so gpx will make some up\nG1 Z5 ; move the platform 5mm down\nG28 Z F500 ; so we can home z again slowly\nM132 X Y Z  ; Recall stored home offsets\nT1 ; switch to the left extruder\n;\n; wait for heat up\nG1 X112 Y-72 Z30 F3300 ; move to waiting position (front right corner of print bed)\nM116 ; wait for target temperatures to be reached. GPX only, RepG doesn't understand\n;\n; purge and wipe\nG92 E0 ; set current extruder position as 0 so that E15 below makes sense\nG1 X110 Y-70 Z[first_layer_height] F2400.0 ; move to just on the bed\nG1 X110 Y70 E15 F1200.000 ; extrude a line of filament along the right edge of the bed\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[printer:FFCPro Right]
bed_shape = -114x-75,112x-75,112x75,-114x75
before_layer_gcode = ; layer [layer_num]
end_gcode = M73 P100 ; end build progress\nG162 X Y F2500; home X and Y axes\nG0 Z150; lower Z axis to bottom\nM18; disable all stepper motors\nM109 S0 T0; set bed temperature to 0\nM104 S0 T1; set extruder temperature to 0\nM70 P5; We <3 Making Things!\nM72 P1; Play Ta-Da song\n
extruder_offset = 0x0,0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = PASTE_HERE
octoprint_host = greenpi.local
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 0,0
retract_length = 2,2
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 40,40
start_gcode = ; begin\nM73 P0 ; tell the firmware we're starting a build\nG130 X118 Y118 Z40 A118 B118  ; set vref's to default\n;\n; set temps\nM140 S[first_layer_bed_temperature] ; set bed temp, don't wait\nM104 S[first_layer_temperature_0] T0 ; set nozzle temp, don't wait\n;\n; home and set coordinates\n\nT0 ; home on the right extruder\nG90 ;  set positioning to absolute\nG28 X Y Z ; home XYZ at default home feedrates\n; home Z again slowly to give more consistent first layer height\nG92 X0 Y0 Z0 A0 B0 ; define this as Z=0, the other coords are technically unnecessary but x3g requires them so gpx will make some up\nG1 Z5 ; move the platform 5mm down\nG28 Z F500 ; so we can home z again slowly\nM132 X Y Z  ; Recall stored home offsets\n\n;\n; wait for heat up\nG1 X112 Y-72 Z30 F3300 ; move to waiting position (front right corner of print bed)\nM116 ; wait for target temperatures to be reached. GPX only, RepG doesn't understand\n;\n; purge and wipe\nG92 E0 ; set current extruder position as 0 so that E15 below makes sense\nG1 X110 Y-70 Z[first_layer_height] F2400.0 ; move to just on the bed\nG1 X110 Y70 E15 F1200.000 ; extrude a line of filament along the right edge of the bed\nG92 E0 ; set E to 0 again because the slicer's next extrusion is relative to this 0\n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[settings]
autocenter = 1
mode = expert