Command Reference
Firstly you can get a quick reminder of commands using the MMU_HELP command from the console:
MMU_HELP
Happy Hare MMU commands: (use MMU_HELP MACROS=1 TESTING=1 STEPS=1 for full command set)
MMU : Enable/Disable functionality and reset state
MMU_CHANGE_TOOL : Perform a tool swap (called from Tx command)
MMU_CHECK_GATE : Automatically inspects gate(s), parks filament and marks availability
MMU_EJECT : aka MMU_UNLOAD Eject filament and park it in the MMU or optionally unloads just the extruder (EXTRUDER_ONLY=1)
MMU_ENCODER : Display encoder position and stats or enable/disable runout detection logic in encoder
MMU_ENDLESS_SPOOL : Diplay or Manage EndlessSpool functionality and groups
MMU_GATE_MAP : Display or define the type and color of filaments on each gate
MMU_HELP : Display the complete set of MMU commands and function
MMU_HOME : Home the MMU selector
MMU_LED : Manage mode of operation of optional MMU LED's
MMU_LOAD : Loads filament on current tool/gate or optionally loads just the extruder for bypass or recovery usage (EXTRUDER_ONLY=1)
MMU_MOTORS_OFF : Turn off both MMU motors
MMU_PAUSE : Pause the current print and lock the MMU operations
MMU_PRELOAD : Preloads filament at specified or current gate
MMU_RECOVER : Recover the filament location and set MMU state after manual intervention/movement
MMU_RESET : Forget persisted state and re-initialize defaults
MMU_SELECT : Select the specified logical tool (following TTG map) or physical gate
MMU_SELECT_BYPASS : Select the filament bypass
MMU_SENSORS : Query state of sensors fitted to mmu
MMU_SERVO : Move MMU servo to position specified position or angle
MMU_SLICER_TOOL_MAP : Display or define the tools used in print as specified by slicer
MMU_STATS : Dump and optionally reset the MMU statistics
MMU_STATUS : Complete dump of current MMU state and important configuration
MMU_SYNC_GEAR_MOTOR : Sync the MMU gear motor to the extruder stepper
MMU_TOOL_OVERRIDES : Displays, sets or clears tool speed and extrusion factors (M220 & M221)
MMU_TTG_MAP : aka MMU_REMAP_TTG Display or remap a tool to a specific gate and set gate availability
MMU_UNLOCK : Wakeup the MMU prior to resume to restore temperatures and timeouts
Basic MMU functionality| Command | Description | Parameters |
|---|---|---|
MMU |
Enable and reset state or disable the MMU. Useful to completely turn off the MMU functionality rather then uninstalling it. Note that persisted state will be reset when re-enabling | ENABLE=[0|1] |
MMU_HOME |
Home the MMU selector and optionally selects gate associated with the specified tool |
TOOL=[0..n] After homing, select gate associated with this tool FORCE_UNLOAD=[0|1] Optional. If specified will override default intelligent filament unload behavior prior to homing |
MMU_SELECT |
Selects the logical tool or physical gate. If tool is sepficed the gate associated with the specified tool (TTG map) will be selected |
TOOL=[0..n] The tool to be selected (will actually select the gate currently mapped to the tool with TTG) GATE=[0..n] The gate to be selected (ignores TTG map) BYPASS=1 Selects the bypass selector position if configured (same as MMU_SELECT_BYPASS) |
MMU_SELECT_BYPASS |
Select the bypass selector position if configured | None |
MMU_CHANGE_TOOL |
Perform a tool swap (generally called from 'Tx' macros). Use STANDALONE=1 option in your print_start macro to saftely load the initial tool |
TOOL=[0..n] STANDALONE=[0|1] Optional to force standalone logic (tip forming)QUIET=[0|1] Optional to always suppress swap statistics |
MMU_LOAD |
Loads filament in currently selected tool/gate to extruder. Optionally performs just the extruder load part of the sequence - designed for bypass loading or non MMU use |
EXTRUDER_ONLY=[0|1] To force just the extruder loading (automatic if bypass selected) |
MMU_LED |
Quick way to try/test modes of operation of optional MMU LEDs |
ENABLE=[0|1] Whether LED's are operational or not EFFECT=[off|gate_status|filament_color|slicer_color] Selects the default effect for gate LEDs when no action is taking place EXIT_EFFECT=[off|filament_color|slicer_color] Selects the default effect for exit LED when no action is taking place |
MMU_EJECT |
MMU_UNLOAD |
Eject filament and park it in the MMU gate or does the extruder unloading part of the unload sequence if in bypass |
MMU_PRELOAD |
Helper for filament loading. Feed filament into gate, MMU will catch it and correctly position at the specified gate |
GATE=[0..n] The specific gate to preload. If omitted the currently selected gate will be loaded |
MMU_PAUSE |
Pause the current print and lock the MMU operations. (MMU_UNLOCK + RESUME or just RESUME to continue print) |
FORCE_IN_PRINT=[0|1] This option forces the handling of pause as if it occurred in print and is useful for testing. Calls PAUSE by default or your pause_macro if set MSG=<message> Supply message to be displayed. Useful when used in macros |
MMU_RECOVER |
Recover filament position and optionally reset MMU state. Useful to call prior to RESUME if you intervene/manipulate filament by hand |
TOOL=[0..n]|-2 Optionally force set the currently selected tool (-2 = bypass). Use caution! GATE=[0..n] Optionally force set the currently selected gate if TTG mapping is being leveraged otherwise it will get the gate associated with current tool. Use caution! LOADED=[0|1] Optionally specify if the filamanet is fully loaded or fully unloaded. Use caution! If not specified, MMU will try to discover filament position STRICT=[0|1] If automatically detecting impose stricter testing for filament position (temporarily sets 'strict_filament_recovery' parameter) |
MMU_ENCODER |
Displays the current value of the MMU encoder or explicitly enable or disable the encoder. Note that the encoder state is set automatically so this will only be sticky until next tool change |
ENABLE=[0|1] 0=Disable, 1=Enable VALUE=.. Set the current distance |
MMU_FORM_TIP |
see MMU_TEST_FORM_TIP
|
|
MMU_TOOL_OVERRIDES |
Displays, sets or clears tool speed and extrusion factors (M220 & M221) |
TOOL=[0..n] Specify tool to set M220=[0-200] Speed (feedrate) multiplier percentage M221=[0-200] Extrusion multiplier percentage RESET=1 Reset specified override for specified tool to default 100%. Note that omitting TOOL= will reset all tools |
MMU_UNLOCK |
Wakeup the MMU prior to RESUME to restore temperatures and timeouts | None |
MMU_HELP |
Generate reminder list of command set |
TESTING=[0|1] Also list the testing commands MACROS=[0|1] Also list the callback backros |
| Command | Description | Parameters |
|---|---|---|
MMU_CHECK_GATE |
Inspect the gate(s) and mark availability. By default it will check just the current gate but options allow many |
ALL=1 To check all gates GATE=[0..n] The specific gate to check TOOL=[0..n] The specific too to check (same as gate if no TTG mapping in place) TOOLS={csv} The list of tools to check. Typically used in print start macro to validate all necessary tools GATES={csv} The list of gates to check. If all parameters are omitted the current gate will be checked (the default) QUIET=[0|1] Optional, supresses dump of gate status at end of checking procedure |
MMU_GATE_MAP |
Without parameters this will display the current gate map. Optionally configure the filament type, color and availabilty. Used in colored UI's and available via printer variables in your print_start macro |
RESET=1 If specified the 'gate_materials, 'gate_colors' and 'gate_status' will be reset to that defined in mmu_parameters.cfg The following must be specified together to create a complete entry in the gate map: GATE=[0..n] Gate number GATES={csv} The list of gates to set. Can be used as an alternative to a single GATE=.. MATERIAL=.. The material type. Short, no spaces. e.g. "PLA+" COLOR=.. The color of the filament. Can be a string representing one of the w3c color names e.g. "violet" or a color string in the hexadeciaml format RRGGBB e.g. "ff0000" for red. NO space or # symbols. Empty string for no color AVAILABLE=[0|1|2] Optionally marks gate as empty (0) or available from spool (1) or available from buffer (2) SPEED=[10..150] Optional and controls the speed and accelaration factor (percent) used in loading and unloading moves. This is particularly useful when special handling is required for TPU material SPOOLID=.. The SpoolMan SpoolID (integer) if SpoolMan support is enabled QUIET=[0|1] Optional. Supresses dump of current gate map to log file REFRESH=1 Will refresh data from Spoolman if configured for all filaments NEXT_SPOOLID=.. Will auto assign specified spool_id to the next gate preloaded either specifically or registered by pre-gate sensor. Valid for pending_spool_id_timeout seconds (useful for RFID reader) DETAIL=1 for additional information |
MMU_TTG_MAP |
Reconfiguration of the Tool-to-Gate (TTG) map. Can also set gates as empty! |
RESET=1 If specified the Tool -> Gate mapping will be reset to that defined in mmu_parameters.cfg TOOL=[0..n] Tool to set in TTG map GATE=[0..n] Maps specified tool to this gate (multiple tools can point to same gate) AVAILABLE=[0|1] Marks gate as available or empty QUIET=[0|1] Optional. Supresses dump of current TTG map to log file MAP={csv} List of gates, one for each tool to specify the entire TTG map for bulk updates |
MMU_ENDLESS_SPOOL |
With parameters this will display the EndlessSpool groups. It can also modify the defined EndlessSpool groups at runtime |
RESET=1 If specified the EndlessSpool groups will be reset to that defined in mmu_parameters.cfg GROUPS={csv of groups} The same format as the default groups defined in mmu_parameters.cfg. Must be the same length as the number of MMU gates |
MMU_SLICER_TOOL_MAP |
Used to set or display (no parameters) tools used in print. Typically this will be set in the print_start macro based on placeholders from the slicer including filament color, material type and temperature setting. This detail can be used in print by reading the printer variable. For example, printer.mmu. slicer_tool_map. tools.5.material will contain the material the slicer is expecting in tool T5 or printer.mmu. slicer_tool_map. purge_volumes[0][2] the volume in mm^3 to purge when changing from tool T0 to T2 |
TOOL the tool to set MATERIAL the material type e.g. PLA or ABS COLOR the color in form RRBBGG TEMP the filament print temperature USED=[0|1] Whether the tool is used in current print. Defaults to 1 (used) PURGE_VOLUMES a comma separated list of purge volumes when changing tools. Map is always NxN but the volumes can be specified as a single volume (same unload/load on every tool), N volumes (same unload/load volume separately for each tool), 2xN volumes (specific unload/load volumes for each tool), or NxN volumes (every possible unload tool and load tool) QUIET=[0|1] whether to suppress output after set RESET=[0|1] used to reset/clear the map DETAIL=1 will dump the purge volumes map and all tools regardless of whether they are used |
| Command | Description | Parameters |
|---|---|---|
MMU_RESET |
Reset the MMU persisted state back to defaults |
CONFIRM=[0|1] Must be sepcifed for affirmative action of this dangerous command |
MMU_STATS |
Dump (and optionally reset) the MMU statistics for current print job or total |
RESET=1 If specified the persisted statistics will be reset (will only apply to counts if COUNTER argument is supplied) TOTAL=[0|1] whether to also show the total swap stats in addition to the current/last print job DETAIL=[0|1] Whether to display additional details about the per-gate statistics COUNTER=<name> Consumption counter name LIMIT=<int> The maximum count for consumption counter before warning WARNING="<message>" The warning message to issue when the counter exceeds limit PAUSE=1 Whether to pause the print when the limit is reach verses just warning INCR=1 Increment the consumption counter by one (can be any positive number) DELETE=1 deletes the specified consumption counter completely (use RESET=1 to reset count to 0) SHOWCOUNTS=1 will also display the comsuption counters |
MMU_STATUS |
Report on MMU state, capabilities and Tool-to-Gate map |
DETAIL=[0|1] Whether to show a more detailed view including EndlessSpool groups and full Tool-To-Gate mapping SHOWCONFIG=[0|1] (default 0) Whether or not to describe the machine configuration in status message |
MMU_SENSORS |
Report on the state of all sensors connected to the MMU |
DETAIL=[0|1] Whether to show all disabled sensors or just active ones |
| Command | Description | Parameters |
|---|---|---|
MMU_SERVO |
Set the servo to specified postion or a sepcific angle for testing. Will also report position when run without parameters |
POS=[up|down|move] Move servo to predetermined position ANGLE=.. Move servo to specified angle SAVE=1 Specifed with the POS= parameter will cause Happy Hare to store the current servo angle for the specified position. This is written to mmu_vars.cfg
|
MMU_MOTORS_OFF |
Turn off both MMU motors | None |
MMU_SYNC_GEAR_MOTOR |
Explicitly override the synchronization of extruder and gear motors. Note that synchronization is set automatically so this will only be sticky until the next tool change |
SYNC=[0|1] Turn gear/extruder synchronization on/off (default 1) SERVO=[0|1] If 1 (the default) servo will engage if SYNC=1 or disengage if SYNC=0 otherwise servo position will not change FORCE_IN_PRINT=[0|1] If 1, gear stepper current will be set according to sync_gear_current. If 0, gear stepper current is set to 100%. The default is automatically determined based on print state but can be overridden with this argument. Only meaningful if SYNC=1
|
MMU_CALIBRATE_BOWDEN : Calibration of reference bowden length for gate 0
MMU_CALIBRATE_ENCODER : Calibration routine for the MMU encoder
MMU_CALIBRATE_GATES : Optional calibration of individual MMU gate
MMU_CALIBRATE_GEAR : Calibration routine for gear stepper rotational distance
MMU_CALIBRATE_SELECTOR : Calibration of the selector positions or postion of specified gate
MMU_CALIBRATE_TOOLHEAD : Calibration of key toolhead distances
MMU_COLD_PULL : Guide you through the process of cleaning your extruder with a cold pull| Command | Description | Parameters |
|---|---|---|
MMU_SERVO |
Set the servo to specified postion or a sepcific angle for testing. Will also report position when run without parameters |
POS=[up|down|move] Move servo to predetermined position ANGLE=.. Move servo to specified angle SAVE=1 Specifed with the POS= parameter will cause Happy Hare to store the current servo angle for the specified position. This is written to mmu_vars.cfg
|
MMU_CALIBRATE_GEAR |
Calibration rourine for the the gear stepper rotational distance |
LENGTH=.. length to test over (default 100mm) MEASURED=.. User measured distance SAVE=[0|1] (default 1) Whether to save the result |
MMU_CALIBRATE_ENCODER |
Calibration routine for MMU encoder |
LENGTH=.. Distance (mm) to measure over. Longer is better, defaults to 400mm REPEATS=.. Number of times to average over SPEED=.. Speed of gear motor move. Defaults to long move speed ACCEL=.. Accel of gear motor move. Defaults to motor setting in ercf_hardware.cfg MINSPEED=.. & MAXSPEED=.. If specified the speed is increased over each iteration between these speeds (only for experimentation) SAVE=[0|1] (default 1) Whether to save the result |
MMU_CALIBRATE_SELECTOR |
Calibration of the selector gate positions. By default will automatically calibrate every gate. ERCF v1.1 users must specify the bypass block position if fitted. If GATE to BYPASS option is sepcifed this will update the calibrate for a single gate |
GATE=[0..n] The individual gate position to calibrate BYPASS=[0|1] Calibrate the bypass position BYPASS_BLOCK=.. Optional (v1.1 only). Which bearing block contains the bypass where the first one is numbered 1 SAVE=[0|1] (default 1) Whether to save the result |
MMU_CALIBRATE_BOWDEN |
Measure the calibration length of the bowden tube used for fast load movement. This will be performed on gate #0 |
BOWDEN_LENGTH=.. The approximate length of the bowden tube but NOT longer than the real measurement. 50mm less that real is a good starting point HOMING_MAX=.. (default 100) The distance after the sepcified BOWDEN_LENGTH to search of the extruder entrance REPEATS=.. (default 3) Number of times to average measurement over SAVE=[0|1] (default 1) Whether to save the result MANUAL=1 This allows for calibration without an encoder |
MMU_CALIBRATE_GATES |
Optional calibration for loading of a sepcifed gate or all gates. This is calculated as a ratio of gate #0 and thus this is usually the last calibration step |
GATE=[0..n] The individual gate position to calibrate ALL[0|1] Calibrate all gates 1..n sequentially (filament must be available in each gate) LENGTH=.. Distance (mm) to measure over. Longer is better, defaults to 400mm REPEATS=.. Number of times to average over SAVE=[0|1] (default 1) Whether to save the result |
MMU_CALIBRATE_TOOLHEAD |
Optional calibration of key toolhead dimension and toolhead cutting variables. This should be run as instructed in Blobbing and Stringing |
CLEAN=1 This will calibrate toolhead_extruder_to_nozzle, toolhead_sensor_to_nozzle, toolhead_entry_to_extruder Without parameters this will calibrate toolhead_ooze_reduction CUT=1 Calibrate variable_blade_pos for the tip cutting macro |
MMU_COLD_PULL |
This command (implement as a macro) should be run as instructed in Blobbing and Stringing. It walks you through the process automating much of the work |
MATERIAL=[nylon|pla|abs|petg] Specify the type of material you are using for the cold pull for temperature defaults HOT_TEMP=xxx Override initial high temp in °C COLD_TEMP=xxx Override temp to cool too to help release filament MIN_EXTRUDE_TEMP=xxx Override temp to which the extruder will keep nozzle pressurized PULL_TEMP=xxx Override temp to perform the cold pull PULL_SPEED=[10] Optionally change the speed of extruder movement to help manual pull in mm/s CLEAN_LENGTH=[25] Optionally change the amount of filament to extrude to prime extruder/nozzle EXTRUDE_SPEED=[1.5] Optionally change speed in mm/s to perform extrude operations |
MMU_SOAKTEST_LOAD_SEQUENCE : Soak test tool load/unload sequence
MMU_SOAKTEST_SELECTOR : Soak test of selector movement
MMU_TEST_BUZZ_MOTOR : Simple buzz the selected motor (default gear) for setup testing
MMU_TEST_CONFIG : Runtime adjustment of MMU configuration for testing or in-print tweaking purposes
MMU_TEST_FORM_TIP : Convenience macro for calling the standalone tip forming functionality (or cutter logic)
MMU_TEST_GRIP : Test the MMU grip for a Tool
MMU_TEST_HOMING_MOVE : Test filament homing move to help debug setup / options
MMU_TEST_LOAD : For quick testing filament loading from gate to the extruder
MMU_TEST_MOVE : Test filament move to help debug setup / options
MMU_TEST_RUNOUT : Manually invoke the clog/runout detection logic for testing
MMU_TEST_TRACKING : Test the tracking of gear feed and encoder sensing| Command | Description | Parameters |
|---|---|---|
MMU_SOAKTEST_SELECTOR |
Reliability testing to put the selector movement under stress to test for failures. Randomly selects gates and occasionally re-homes |
LOOP=..[100] Number of times to repeat the test SERVO=[0|1] Whether to include the servo down movement in the test HOME=[0|1] Whether to include randomized homing operations |
MMU_SOAKTEST_LOAD_SEQUENCE |
Soak testing of load sequence. Great for testing reliability and repeatability |
LOOP=..[10] Number of times to loop while testing RANDOM=[0|1] Whether to randomize tool selection FULL=[0|1] Whether to perform full load to nozzle or short load just past encoder |
MMU_TEST_BUZZ_MOTOR |
Buzz the sepcified MMU motor. If the gear motor is buzzed it will also report if filament is detected | MOTOR=[gear|selector|servo] |
MMU_TEST_CONFIG |
Dump / Change Happy Hare klipper parameter config options at runtime | Many. Best to run MMU_TEST_CONFIG without options to report all parameters than can be specified You must manually update mmu_parameters.cfg to persist the change accross restarts Note: this only modifies Happy Hare klipper parameters in mmu_parameters.cfg; Happy Hare macro variables in mmu_macro_vars.cfg can be updated in a similar way using SET_GCODE_VARIABLE. See Macro Variable Tip
|
MMU_TEST_FORM_TIP : Convenience macro to call to test the standalone tip forming functionality |
Any valid _MMU_FORM_TIP gcode variable can be supplied as a parameter and will override the defaults in the mmu_software.cfg file. overrides will remain active (sticky) until called with RESET=1 which will cause Happy Hare to revert to starting values (in mmu_software.cfg) SHOW=1 will just list the current macro variable values and not run macro RUN=0 will set the variable but not run the macro FORCE_IN_PRINT=1 behave like in print with gear/extruder syncing and current EJECT=[0|1] Force ejection of filament after tip forming, akin to setting variable_final_eject=1
|
|
MMU_TEST_GRIP |
Test the MMU grip of the currently selected tool by gripping filament but relaxing the gear motor so you can check for good contact | None |
MMU_TEST_LOAD |
Test loading filament from park position in the gate. (MMU_EJECT will unload) |
LENGTH=..[100] Test load the specified length of filament into selected tool FULL=[0|1] If set to one a full bowden move will occur and filament will home to extruder |
MMU_TEST_MOVE |
Simple test move the MMU gear stepper |
MOVE=..[100] Length of gear move in mm SPEED=.. (defaults to speed defined to type of motor/homing combination) Stepper move speed ACCEL=.. (defaults to min accel defined on steppers employed in move) Motor acceleration MOTOR=[gear|extruder|gear+extruder|extruder+gear] (default: gear) The motor or motor combination to employ. gear+extruder commands the gear stepper and links extruder to movement, extruder+gear commands the extruder stepper and links gear to movement |
MMU_TEST_HOMING_MOVE |
Testing homing move of filament using multiple stepper combinations specifying endstop and driection of homing move |
MOVE=..[100] Length of gear move in mm SPEED=.. (defaults to speed defined to type of motor/homing combination) Stepper move speed ACCEL=.. Motor accelaration (defaults to min accel defined on steppers employed in homing move) MOTOR=[gear|extruder|gear+extruder|extruder+gear] (default: gear) The motor or motor combination to employ. gear+extruder commands the gear stepper and links extruder to movement, extruder+gear commands the extruder stepper and links gear to movement. This is important for homing because the endstop must be on the commanded stepper ENDSTOP=.. Symbolic name of endstop to home to as defined in mmu_hardware.cfg. Must be defined on the primary stepper STOP_ON_ENDSTOP=[1|-1] (default 1) The direction of homing move. 1 is in the normal direction with endstop firing, -1 is in the reverse direction waiting for endstop to release. Note that virtual (touch) endstops can only be homed in a forward direction |
MMU_TEST_RUNOUT |
Invoke filament runout handler that will also trigger EndlessSpool if enabled and thus useful to validate your load/unload sequence macros (define in mmu_sequence.cfg) |
FORCE_RUNOUT=0 optional parameter (defaults to 1) that if set to 0 will cause HH to try to determine if a clog vs runout by also running a filament movement test |
MMU_TEST_TRACKING |
Simple visual test to see how encoder tracks with gear motor |
DIRECTION=[-1|1] Direction to perform the test (default load direction) STEP=[0.5 .. 20] Size of individual steps (default 1mm) SENSITIVITY=.. (defaults to expected encoder resolution) Sets the scaling for the +/- mismatch visualization |
MMU_END : Called when ending print to finalize MMU
MMU_START_CHECK : Helper macro. Can be called to perform pre-start checks on MMU based on slicer requirements
MMU_START_LOAD_INITIAL_TOOL : Helper to load initial tool if not paused
MMU_START_SETUP : Called when starting print to setup MMU
_MMU_ACTION_CHANGED : Called when an action has changed
_MMU_DUMP_TOOLHEAD : For debugging: dump current configuration of MMU Toolhead rails
_MMU_GATE_MAP_CHANGED : Called when gate map is updated
_MMU_LOAD_SEQUENCE : Called when MMU is asked to load filament
_MMU_POST_FORM_TIP : Optional post tip forming/cutting routing
_MMU_POST_LOAD : Optional post load routine for filament change
_MMU_POST_UNLOAD : Optional post unload routine for filament change
_MMU_PRE_LOAD : Optional pre load routine for filament change
_MMU_PRE_UNLOAD : Optional pre unload routine for filament change
_MMU_PRINT_END : Cleans up state after after print end
_MMU_PRINT_START : Initialize MMU state and ready for print
_MMU_PRINT_STATE_CHANGED : Called when print state changes
_MMU_UNLOAD_SEQUENCE : Called when MMU is asked to unload filamentSee Slicer Setup for details
| Macro | Description | Parameters |
|---|---|---|
MMU_START_SETUP |
Call when starting print to setup MMU |
INITIAL_TOOL, REFERENCED_TOOLS, TOOL_COLORS, TOOL_TEMPS, TOOL_MATERIALS. See Slicer Setup for details |
MMU_START_CHECK |
Helper macro. Can be called to perform pre-start checks on MMU based on slicer requirements | |
MMU_START_LOAD_INITIAL_TOOL |
Helper to load initial tool if not paused | |
MMU_END |
Called when ending print to finalize MMU |
EJECT=[0|1] Override the macro setting for final unloading of filament |
_MMU_UPDATE_HEIGHT |
Called on layer change to record maximum toolhead height for z-hop base for sequential printing | 'HEIGHT=..' Optionally reset the minimum height. Normally not specified |
Callbacks (defined in mmu_software.cfg, mmu_form_tip.cfg, mmu_cut_tip.cfg, mmu_sequence.cfg, mmu_state.cfg, mmu_leds.cfg):
| Macro | Description | Supplied Parameters |
|---|---|---|
_MMU_PRE_UNLOAD |
Called prior to unloading on toolchange | |
_MMU_POST_FORM_TIP |
Called immediately after forming tip | |
_MMU_POST_UNLOAD |
Called after unload is complete and filament is parked at the gate | |
_MMU_PRE_LOAD |
Called prior to the loading of a new filament | |
_MMU_POST_LOAD |
Called subsequent to loading new filament | |
_MMU_FORM_TIP |
Called to create tip on filament (when not under the control of the slicer). You tune this macro by modifying the defaults to the parameters | |
_MMU_CUT_TIP |
Called to create tip by cutting the filament. You tune this macro by modifying the defaults to the parameters | |
_MMU_ACTION_CHANGED |
Callback that is called everytime the printer.ercf.action is updated. Great for contolling LED lights, etc |
|
_MMU_PRINT_STATE_CHANGED |
Callback when the print job state changes and printer.ercf.print_state is updated. Great for contolling LED lights, etc |
|
_MMU_GATE_MAP_CHANGED |
Called when gate map is updated. Useful for updating LED lights, etc | |
_MMU_LOAD_SEQUENCE |
Advanced: Called when MMU is asked to load filament |
FILAMENT_POS LENGTH FULL HOME_EXTRUDER SKIP_EXTRUDER EXTRUDER_ONLY
|
_MMU_UNLOAD_SEQUENCE |
Advanced: Called when MMU is asked to unload filament |
FILAMENT_POS LENGTH EXTRUDER_ONLY PARK_POS
|
_MMU_M400 : Wait on both move queues
_MMU_STEP_HOME_EXTRUDER : User composable loading step: Home to extruder sensor or entrance through collision detection
_MMU_STEP_HOMING_MOVE : User composable loading step: Generic homing move
_MMU_STEP_LOAD_BOWDEN : User composable loading step: Smart loading of bowden
_MMU_STEP_LOAD_GATE : User composable loading step: Move filament from gate to start of bowden
_MMU_STEP_LOAD_TOOLHEAD : User composable loading step: Toolhead loading
_MMU_STEP_MOVE : User composable loading step: Generic move
_MMU_STEP_SET_FILAMENT : User composable loading step: Set filament position state
_MMU_STEP_UNLOAD_BOWDEN : User composable unloading step: Smart unloading of bowden
_MMU_STEP_UNLOAD_GATE : User composable unloading step: Move filament from start of bowden and park in the gate
_MMU_STEP_UNLOAD_TOOLHEAD : User composable unloading step: Toolhead unloading| Macro | Description | Parameters |
|---|---|---|
_MMU_M400 |
User composable loading step that will force a wait on both the toolhead and mmu move queues | |
_MMU_STEP_LOAD_GATE |
User composable loading step: Move filament from gate to start of bowden using encoder or gate sensor | |
_MMU_STEP_LOAD_BOWDEN |
User composable loading step: Smart loading of bowden | LENGTH=.. |
_MMU_STEP_HOME_EXTRUDER |
User composable loading step: Extruder collision detection | |
_MMU_STEP_LOAD_TOOLHEAD |
User composable loading step: Toolhead loading | EXTRUDER_ONLY=[0|1] |
_MMU_STEP_UNLOAD_TOOLHEAD |
User composable unloading step: Toolhead unloading |
EXTRUDER_ONLY=[0|1] PARK_POS=..
|
_MMU_STEP_UNLOAD_BOWDEN |
User composable unloading step: Smart unloading of bowden |
FULL=[0|1] LENGTH=..
|
_MMU_STEP_UNLOAD_GATE |
User composable unloading step: Move filament from start of bowden and park in the gate using encoder or gate sensor | FULL=[0|1] |
_MMU_STEP_SET_FILAMENT |
User composable loading step: Set filament position state |
STATE=[0..8] SILENT=[0|1]
|
_MMU_STEP_MOVE |
User composable loading step: Generic move |
MOVE=..[100] Length of gear move in mm SPEED=.. (defaults to speed defined to type of motor/homing combination) Stepper move speed ACCEL=.. (defaults to min accel defined on steppers employed in move) Motor acceleration MOTOR=[gear|extruder|gear+extruder|extruder+gear] (default: gear) The motor or motor combination to employ. gear+extruder commands the gear stepper and links extruder to movement, extruder+gear commands the extruder stepper and links gear to movement |
_MMU_STEP_HOMING_MOVE |
User composable loading step: Generic homing move |
MOVE=..[100] Length of gear move in mm SPEED=.. (defaults to speed defined to type of motor/homing combination) Stepper move speed ACCEL=.. Motor accelaration (defaults to min accel defined on steppers employed in homing move) MOTOR=[gear|extruder|gear+extruder|extruder+gear] (default: gear) The motor or motor combination to employ. gear+extruder commands the gear stepper and links extruder to movement, extruder+gear commands the extruder stepper and links gear to movement. This is important for homing because the endstop must be on the commanded stepper ENDSTOP=.. Symbolic name of endstop to home to as defined in mmu_hardware.cfg. Must be defined on the primary stepper STOP_ON_ENDSTOP=[1|-1] (default 1) The direction of homing move. 1 is in the normal direction with endstop firing, -1 is in the reverse direction waiting for endstop to release. Note that virtual (touch) endstops can only be homed in a forward direction |
Note
Working reference PAUSE / RESUME / CANCEL_PRINT macros are defined in client_macros.cfg and can be used/modified if you don't already have your own