You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Port65 of Wedge100bf_65x enable RS-FEC and Port speed is 100Gb, can't link success with HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter
(Adapter chip is mellanox connectx-4)
Steps to reproduce the issue:
portconfig -p Ethernet256 -f rs -s 100000 on Wedge100bf_65x
show interfaces status Ethernet256 @ wedge100bf_65x
Interface Lanes Speed MTU Alias Vlan Oper Admin Type Asym PFC
Ethernet256 256,257,258,259 100G 9100 Ethernet256 trunk down up QSFP28 or later N/A
sudo mlxlink -d 37:00.0 -p 1 ON HPE-100G 840QSFP28 Adapter
Operational Info
State : Physical LinkUp
Physical state : LinkUp
Speed : 100GbE
Width : 4x
FEC : Standard RS-FEC - RS(528,514)
Loopback Mode : No Loopback
Auto Negotiation : ON
Status Opcode : 14
Group Opcode : PHY FW
Recommendation : Peer is sending remote faults.
Describe the results you received:
Port-65 of wedge100bf_65x can't link success and HPE 100G-840QSFP28 Adapter display error message (Peer is sending remote faults)
Describe the results you expected:
Port-65 should be linked success at normally status
Additional information you deem important (e.g. issue happens only occasionally):
The text was updated successfully, but these errors were encountered:
robert1030
changed the title
Port-65 of Accton Wedge100bf_65x can't link success with HPE-100G-840QSFP28 Adapter, when enable RS-FEC
Port-65 of BFN Wedge100bf_65x can't link success with HPE-100G-840QSFP28 Adapter, when enable RS-FEC
Oct 17, 2019
Description
Port65 of Wedge100bf_65x enable RS-FEC and Port speed is 100Gb, can't link success with HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter
(Adapter chip is mellanox connectx-4)
Steps to reproduce the issue:
config interface startup Ethernet256
Interface Lanes Speed MTU Alias Vlan Oper Admin Type Asym PFC
Ethernet256 256,257,258,259 100G 9100 Ethernet256 trunk down up QSFP28 or later N/A
Operational Info
State : Physical LinkUp
Physical state : LinkUp
Speed : 100GbE
Width : 4x
FEC : Standard RS-FEC - RS(528,514)
Loopback Mode : No Loopback
Auto Negotiation : ON
Supported Info
Enabled Link Speed : 0x00f180c0 (100G,40G)
Supported Cable Speed : 0xf8f1f1d3 (100G,56G,50G,40G,25G,10G,1G)
Troubleshooting Info
Status Opcode : 14
Group Opcode : PHY FW
Recommendation : Peer is sending remote faults.
Describe the results you received:
Port-65 of wedge100bf_65x can't link success and HPE 100G-840QSFP28 Adapter display error message (Peer is sending remote faults)
Describe the results you expected:
Port-65 should be linked success at normally status
Additional information you deem important (e.g. issue happens only occasionally):
HPE-100G 840QSFP28 Adapter driver: MLNX_OFED_LINUX-4.7-1.0.0.1-ubuntu16.04-x86_64
HPE-100G 840QSFP28 Adapter Firmware:
sudo mlxfwmanager -d 37:00.0 --query
Querying Mellanox devices firmware ...
Device #1:
Device Type: ConnectX4
Part Number: 825110-B21_Ax_Bx
Description: HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter
PSID: HP_2180110032
PCI Device Name: 37:00.0
Base MAC: 040973e1cbf4
Versions: Current Available
FW 12.25.1020 N/A
PXE 3.5.0701 N/A
UEFI 14.18.0019 N/A
Status: No matching image found
Wedge100bf_65x SONiC version: SONiC.HEAD.437-dirty-20191005.065051
The text was updated successfully, but these errors were encountered: