-
-
Notifications
You must be signed in to change notification settings - Fork 9
DIY Preperation
Andruszczenko, Eugene edited this page Sep 13, 2018
·
14 revisions
So yo've decided to build the Gaboze Pocaio yourself from scratch.
First of, you are going to need some components. Below is a BOM with source links to purchase.
Designator | Description | Manufacturer Part Number | Purchase Link | Quantity |
---|---|---|---|---|
POWER1 | Lithium Battery Charging Board | N/A | AliExpress | 1 |
R2 | RES SMD 1.5K OHM 0.1% 1/4W 0805 | ERJ-PB6B1501V | DigiKey | 1 |
R1 | RES 3.9 OHM 1% 1/8W 0805 | RMCF0805FT3R90 | DigiKey | 1 |
R3 | RES 100K OHM 5% 1/4W 0805 | RPC0805JT100KCT | DigiKey | 1 |
C1 | CAP TANT 100UF 4V 20% 1206 | F930G107MAA | DigiKey | 1 |
R4 | RES 150 OHM 1% 1/4W 0805 | RNCP0805FTD150R | DigiKey | 1 |
C3, C4 | CAP CER 1UF 25V X7R 0805 | C0805C105K3RACTU | DigiKey | 2 |
C2 | CAP CER 220PF 50V X7R 0805 | C0805C221M5RACTU | DigiKey | 1 |
R10 | Replacement Volume Switch for Game boy | N/A | AliExpress | 1 |
J3 | CONN HEADER PH SIDE 2POS 2MM SMD | S2B-PH-SM4-TB(LF)(SN) | DigiKey | 1 |
2.4TFT-ILI9341 | 2.4 inch SPI Serial LCD | N/A | AliExpress | 1 |
U1 | IC AMP AUDIO PWR 1W MONO 8SOIC | LM4875MX-NOPB | DigiKey | 1 |
PI1 | CONN BERGSTIK II .100" DR SMD | 95157-440LF | DigiKey | 1 |
LED1 | LED RED CLEAR 0603 SMD | LTST-C191KRKT | DigiKey | 1 |
X1 | CONN JACK STEREO 3.5MM R/A | CP1-3525NG-GR-ND | DigiKey | 1 |
U$1 | SWITCH SLIDE SPDT 300MA 4V | MA12RTR | DigiKey | 1 |
J2 | SPEAKER 8OHM 250MW TOP PORT 80DB | PSR-20F08S-JQ | DigiKey | 1 |
J4 | CONN RCPT USB MICRO B SMD | ZX62D-B-5P8(30) | DigiKey | 1 |
Additionally, you can use our Digi-Key prefilled cart;
Region | Link |
---|---|
Canada | http://www.digikey.ca/short/jbb0h2 |
USA | http://www.digikey.com/short/jbb0h2 |
UK | http://www.digikey.co.uk/short/jbb0h2 |
World | Just replace yout top level domain to whatever region you are in |
What you will need to complete this build
- Gaboze Pocaio bare pcb
- Components listed above
- Soldering Iron / Station (yeah, you can use a $10 30w, i've done it)
- Solder (0.3mm 63/37 recommended)
- Polyimide Kapton Tape
- Double Sided Tape
- Game Boy Pocket Shell
- Game Boy Cartridge
- Game Boy Buttons
- Game Boy Silicon Pads
- Game Boy Lens Cover
- Utility Knife
- Square File
- Straight Edge
- Pliers
- Screw Driver