Skip to content

ADM228/ATtiny85APU

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

85 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

ATtiny85APU

This project is creating a soundchip out of an ATtiny85. Written entirely in assembly, it is small enough to fit even onto an ATtiny25/45.

Capabilities

  • 5 channels (named A, B, C, D and E)
    • Each of those has a phase accumulator-powered pulse oscillator with:
      • 8-bit duty cycle
      • 8-bit phase accumulator increment value
      • 3-bit octave value (shifts the increment value for a total 15-bit range)
      • Dedicated phase reset bit
  • Volume control:
    • 2 envelope generators (A and B):
      • Powered by phase accumulators
      • 8-bit phase accumulator increment value
      • 4-bit octave value
        • When the MSB of the octave value is set, the pitch is equivalent to the pulse oscillators
      • Shapes are bit-compatible with the widely used soundchip AY-3-8910, but linear and with 256 steps
      • Dedicated phase reset bit
    • A channel's static volume:
      • 8 bits when not using envelopes
      • When using envelopes, the MSB halves the envelope's volume
    • Panning registers:
      • 2 bits each
      • Always enabled, even without stereo
  • Noise generator:
    • Ticked by phase accumulator similar to the tone ones:
      • 8-bit phase accumulator increment value
      • 3-bit octave value (shifts the increment value for a total 15-bit range)
      • Dedicated phase reset bit (only resets the phase accumulator, not LFSR)
    • Powered by a 16-bit Galois LFSR with adjustable taps
    • The operation is XNOR, always can come back to life
    • On each channel, OR'd with the pulse wave

Registers

The registers themselves:

 ___________ _______ _______________________________________________________________
|           | Bit → |   7   |   6   |   5   |   4   |   3   |   2   |   1   |   0   |
|   Index   |  Name |=======|=======|=======|=======|=======|=======|=======|=======|
|   0x0n    | PILOX |          Pitch increment value for tone on channel X          |
|(n = 0..4,X = A..E)|_______________________________________________________________|
|   0x05    | PILON |           Pitch increment value for noise generator           |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x06    | PHIAB |Ch.B PR|Channel B octave number|Ch.A PR|Channel A octave number|
|   0x07    | PHICD |Ch.D PR|Channel D octave number|Ch.C PR|Channel C octave number|
|   0x08    | PHIEN |NoisePR|Noise gen octave number|Ch.E PR|Channel E octave number|
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x0n    | DUTYX |                   Channel X tone duty cycle                   |
|(n = 9..D,X = A..E)|                                                               |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x0E    | NTPLO |             Noise LFSR inversion value (low byte)             |
|   0x0F    | NTPHI |             Noise LFSR inversion value (high byte)            |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x1n    | VOL_X |                    Channel X static volume                    |
|(n = 0..4,X = A..E)|                                                               |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x1n    | CFG_X | Noise | Envel.| ===== |  Slot |  Right volume |  Left volume  |
|(n = 5..9,X = A..E)| Enable| Enable| ===== | number|               |               |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x1A    | ELDLO |             Low byte of envelope phase load value             |
|   0x1B    | ELDHI |            High byte of envelope phase load value             |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x1C    | E_SHP |EnvB PR|    Envelope B shape   |EnvA PR|    Envelope A shape   |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x1D    | EPLOA |             Pitch increment value for envelope A              |
|   0x1E    | EPLOB |             Pitch increment value for envelope B              |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|   0x1F    | EPIHI |     Envelope B octave num     |     Envelope A octave num     |
|===========|=======|=======|=======|=======|=======|=======|=======|=======|=======|
|___________|_______|_______|_______|_______|_______|_______|_______|_______|_______|

Notes:

  • PR means phase reset in every case
  • The envelope phase load values are shared, and loaded into an envelope when its phase reset bit is set (it can be both)
  • The default values for registers:
    • Most are 0
    • NTPHI is 0x24, sorta corresponding to the AY-3-8910
    • CFG_X is 0x0F, corresponding to maximum panning volume on both sides
  • Since the chip currently only outputs mono audio, only the left panning bits in CFG_X are used. It is recommended to set the right panning bits to the same contents as the left panning bits for compatibility with future versions.
  • Bit 5 of CFG_X is reserved and must be left at 0 for compatibility with future versions.

Real hardware

Firmware

ATtiny85APU assembly

The firmware is located in the avr folder, and is entirely written in AVR assembly. Its size is currently under 2 Kibibytes, therefore it can fit onto an ATtiny25 and '45 in addition to the '85. It is assembled with the avra assembler by running the command make firmware or make avr, which puts the resulting main.hex file into the bin/avr folder.

Connections

The pin connection diagram is:

               __ __
     /Reset -1|° U  |8- VCC
         CS -2|     |7- SPI CLK
        OUT -3|     |6- SPI DO (MOSI)
        GND -4|_____|5- SPI DI (MISO)

Pins 2, 5, 6 and 7 are used for communicating with the register write buffer via SPI. The ATtiny is the master of SPI, checking for new register writes once every sample. The connection is:

CS Function
0 Fetch from register write storage
1 No SPI

Output

Currently, the only available output option is PWM output through the OUT pin. The PWM rate is 2× the sample rate, aka the master clock divided by 256.

Register writes

1 register write is 16 bits long and must work like this:

  1. The MSB must be a "1" for the ATtiny to even proceed to get the register write.
  2. The next 7 bits are the address of the register write
  3. The next 8 bits are the value of the register write

The ATtiny85APU automatically flushes 1 register write per sample, the SPI CLK speed is ½ of the master clock speed (e.g. 4 MHz SPI CLK speed at 8 MHz clock speed). Order of transfer is MSB first.

Clock speeds

Due to all of the pins being busy, the ATtiny85APU cannot receive an external clock signal. Therefore, it only has 2 clock source options:

  • The default internal oscillator:
    • Maximum 8 MHz clock speed, corresponding to 15625 Hz sample rate (and 31250 Hz PWM rate)
    • Divisible by 8 with the CKDIV8 fuse (set by default, it is absolutely recommended to disable this for the sake of your ears)
      • At 8 MHz, can be powered by as little as 2.4V
      • At 4 MHz and lower, can be powered by 1.8V
  • The PLL:
    • 16 MHz clock speed, corresponding to 31250 Hz sample rate (and 62500 Hz PWM rate)
    • Requires at least 3.78V for safe operation

Emulation

ATtiny85APU emulator

The emulator is located in the emu folder. It is written in C99. Features:

  • Fully compatible with the features of the real hardware
  • Cycle-accurate emulation of the output delays from when it was calculated
  • Ability to set arbitrary sample and clock rates
  • 2 resampling quality options available:
    • 0: No resampling
    • 1: Averaging of values on that sample
  • 2 options for emulating PWM output on pin 3:
    • Essentially an 8-bit DAC
    • Actual cycle-accurate PWM emulation
  • Emulation of a register write buffer that register writes can pile up onto and then automatically flushed when it's time to update
    • Sizing can be defined at compile time or runtime via the T85APU_REGWRITE_BUFFER_SIZE define
    • A function that tells you whether an update is pending in the shift register
  • Raw and padded sample output
  • An OOP-based C++ wrapper for your convenience
  • zlib licensed

For more info check out the t85apu.h and t85apu.hpp files. The emulator also provides useful register defines in the t85apu_regdefines.h file.

Manual usage

To use it manually, copy the emu folder into your project, and include the t85apu.h file in C, or t85apu.hpp if you want to use the C++ wrapper. Then, compile the t85apu.c file as a library and link it to the final executable.

Usage with CMake

The emulator also has a CMake API, which makes including it in your project much easier.

Manual inclusion

You can just copy the emu folder into your project, and use add_subdirectory() to add it to your CMakeLists.txt:

add_subdirectory(<your name of the emu folder>)
target_link_libraries(<your_executable_name> PRIVATE t85apu_emu)

Then you can include the aforementioned header files in your code.

Inclusion via FetchContent

You can also just use FetchContent to include the emulator in your project. Here's an example of what to add to your CMakeLists.txt:

include(FetchContent)
FetchContent_Declare(t85apu
  GIT_REPOSITORY https://github.com/ADM228/ATtiny85APU.git
  GIT_TAG main)

set(T85APU_REGWRITE_BUFFER_SIZE 1)
FetchContent_MakeAvailable(t85apu)

target_link_libraries(<your_executable_name> PRIVATE t85apu_emu)

Examples

ATtiny85APU examples

There is an example program provided together with the emulator in C and C++. It is located in the examples folder and illustrates how to use the soundchip and the emulator API:

  • Initialization
  • Pitch control
  • Pitch calculation
  • Duty cycle control
  • Using noise and envelopes
  • Volume control
  • Noise generator control
  • Getting emulator output
  • Deletion

The examples are not built by default as they have the EXCLUDE_FROM_ALL flag enabled, so you don't have to worry about them bloating your software. To build them, you have to explicitly select the example_c and/or example_cpp targets in CMake. The executables will appear in the examples subfolder of where the CMake Cache is.