merged the default toolhead overrides to their MCU templates

install.sh

@@ -164,8 +164,7 @@ function install_mcu_templates {
             # If the user selected a file, copy its content into the mcu.cfg file
             filename=$(basename "${file_list[$((toolhead_template-1))]}")
             cat "${FRIX_CONFIG_PATH}/user_templates/mcu_defaults/toolhead/$filename" >> ${USER_CONFIG_PATH}/mcu.cfg
-            cat "${FRIX_CONFIG_PATH}/user_templates/mcu_defaults/toolhead/overrides/default.cfg" >> ${USER_CONFIG_PATH}/overrides.cfg
-            printf "[CONFIG] Template '$filename' inserted into your mcu.cfg and default overrides added to your overrides.cfg user files\n\n"
+            printf "[CONFIG] Template '$filename' inserted into your mcu.cfg user file\n\n"
         else
             printf "[CONFIG] No toolhead template selected. Skip and continuing...\n\n"
         fi

user_templates/mcu_defaults/toolhead/BTT_EBB36-42_v1.0.cfg

@@ -30,5 +30,38 @@ aliases:
 
     ADXL_CS=MCU_SPI2_CS , ADXL_SCLK=MCU_SPI2_SCLK , ADXL_MISO=MCU_SPI2_MISO , ADXL_MOSI=MCU_SPI2_MOSI ,
 
+
+#----------------------------------------#
+#    BTT EBB36/42 v1.0 pins remapping    #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 [tmc2209 extruder]
 uart_pin: toolhead:E_TMCUART

user_templates/mcu_defaults/toolhead/BTT_EBB36-42_v1.1.cfg

@@ -30,5 +30,38 @@ aliases:
 
     ADXL_CS=MCU_SPI2_CS , ADXL_SCLK=MCU_SPI2_SCLK , ADXL_MISO=MCU_SPI2_MISO , ADXL_MOSI=MCU_SPI2_MOSI ,
 
+
+#----------------------------------------#
+#    BTT EBB36/42 v1.1 pins remapping    #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 [tmc2209 extruder]
 uart_pin: toolhead:E_TMCUART

user_templates/mcu_defaults/toolhead/BTT_EBB36-42_v1.2.cfg

@@ -30,5 +30,38 @@ aliases:
 
     ADXL_CS=MCU_SPI2_CS , ADXL_SCLK=MCU_SPI2_SCLK , ADXL_MISO=MCU_SPI2_MISO , ADXL_MOSI=MCU_SPI2_MOSI ,
 
+
+#----------------------------------------#
+#    BTT EBB36/42 v1.2 pins remapping    #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 [tmc2209 extruder]
 uart_pin: toolhead:E_TMCUART

user_templates/mcu_defaults/toolhead/BTT_SB2209_v1.0.cfg

@@ -31,5 +31,38 @@ aliases:
     ADXL_CS=MCU_SPI2_CS , ADXL_SCLK=MCU_SPI2_CLK , ADXL_MISO=MCU_SPI2_MISO , ADXL_MOSI=MCU_SPI2_MOSI ,
     MAX31865_NSS=MCU_SPI1_NSS , MAX31865_CLK=MCU_SPI1_CLK , MAX31865_MOSI=MCU_SPI1_MOSI , MAX31865_MISO = MCU_SPI1_MISO , 
 
+
+#----------------------------------------#
+#    BTT SB2209 v1.0 pins remapping      #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 [tmc2209 extruder]
 uart_pin: toolhead:E_TMCUART

user_templates/mcu_defaults/toolhead/BTT_SB2240_v1.0.cfg

@@ -31,6 +31,39 @@ aliases:
     ADXL_CS=MCU_SPI2_CS , ADXL_SCLK=MCU_SPI2_CLK , ADXL_MISO=MCU_SPI2_MISO , ADXL_MOSI=MCU_SPI2_MOSI ,
     MAX31865_NSS=MCU_SPI1_NSS , MAX31865_CLK=MCU_SPI1_CLK , MAX31865_MOSI=MCU_SPI1_MOSI , MAX31865_MISO = MCU_SPI1_MISO , 
 
+
+#----------------------------------------#
+#     BTT SB2240 v1.0 pins remapping     #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 # Since ADXL shares pins with the SPI interface of the TMC, it must be set up here, since different pin aliases must not resolve to the same pin
 [tmc2240 extruder]
 cs_pin: toolhead:MCU_MOTOR_SPI_NSS

user_templates/mcu_defaults/toolhead/Mellow_SB2040_v1.cfg

@@ -30,5 +30,38 @@ aliases:
 
     ADXL_CS=MCU_ADXL_CS , ADXL_SCLK=MCU_ADXL_SCK , ADXL_MOSI=MCU_ADXL_MOSI , ADXL_MISO=MCU_ADXL_MISO ,
 
+
+#----------------------------------------#
+#     Mellow SB2040 v1 pins remapping    #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 [tmc2209 extruder]
 uart_pin: toolhead:E_TMCUART

user_templates/mcu_defaults/toolhead/Mellow_SHT36-42_v1.x.cfg

@@ -31,5 +31,38 @@ aliases:
 
     ADXL_CS=MCU_ADXL ,
 
+
+#----------------------------------------#
+#   Mellow SHT36/42 v1.x pins remapping  #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 [tmc2209 extruder]
 uart_pin: toolhead:E_TMCUART

user_templates/mcu_defaults/toolhead/Mellow_SHT36_v2.x.cfg

@@ -30,5 +30,38 @@ aliases:
 
     ADXL_CS=MCU_ADXL ,
 
+
+#----------------------------------------#
+#    Mellow SHT36 v2.x pins remapping    #
+#----------------------------------------#
+
+# These pins overrides are automatically added when you select a CANbus
+# toolhead MCU during the installation process. They should provide a
+# good base to work with. Feel free to adapt to your board if needed!
+
+[extruder]
+step_pin: toolhead:E_STEP
+dir_pin: toolhead:E_DIR
+enable_pin: !toolhead:E_ENABLE
+heater_pin: toolhead:E_HEATER
+sensor_pin: toolhead:E_TEMPERATURE
+
+[probe]
+pin: ^toolhead:PROBE_INPUT
+
+[fan]
+pin: toolhead:PART_FAN
+
+[heater_fan hotend_fan]
+pin: toolhead:E_FAN
+
+## Uncomment the following line if not using sensorless homing
+## and having the X endstop plugged to the toolhead MCU
+# [stepper_x]
+# endstop_pin: ^toolhead:X_STOP
+
+[neopixel status_leds]
+pin: toolhead:STATUS_NEOPIXEL
+
 [tmc2209 extruder]
 uart_pin: toolhead:E_TMCUART