Skip to content
forked from open3e/open3e

connects E3 (vcal, vdens, vx3...) controller through can uds or doip

License

Notifications You must be signed in to change notification settings

SanMiggel/open3e

 
 

Repository files navigation

Open3E interface

  • Connects E3 boiler (vcal or vdens) controller through CAN UDS or doip
  • Read known data points
  • Listen to commands on mqtt
  • Write data points in raw and json data format
  • Experimental write support for service 77 (NOT implemented for listener mode yet)

Installation

Hint: An installation guide is available also in German language.

For a fresh Raspberry PI install git, python3 and python-pip first:

sudo apt install git python3 python3-pip  

Optional, but highly recommended is creating a virtual environment before the installation. Basic instructions, see here: https://packaging.python.org/en/latest/guides/installing-using-pip-and-virtual-environments/#create-and-use-virtual-environments

Now install the latest version of open3e via

pip install git+https://github.com/open3e/open3e.git

or for the develop branch

pip install git+https://github.com/open3e/open3e.git@develop

This will install open3e along with all dependencies.

If you get the error "error: externally-managed-environment" you could add --break-system-packages to the preveious command.
(please see: https://stackoverflow.com/questions/75608323/how-do-i-solve-error-externally-managed-environment-every-time-i-use-pip-3)

Setup CAN Bus

sudo ip link set can0 up type can bitrate 250000

Depict System

In advance of first time starting the client and after every firmware update, run

open3e_depictSystem

to scan the system and generate devices.json and Open3Edatapoints_678.py files. Use open3e with cmd line argument -cnfg devices.json afterwards. Pls. make sure to use same working directory for open3e as used for running open3e_depictSystem.

To refer to a specific device, you have to use "complex addressing mode", e.g. to read dids 268 and 269 of device 0x680 use -cnfg devices.json -r 0x680.268,0x680.269. Do not use option -dev in this context.

It's possible to change naming of devices by editing devices.json: When you change "0x680": { to "vitocal": { you can use read commands like -r vitocal.268,vitocal.269. New naming will also be used for paramter {device}within MQTT topics (see below).

Further information is available here.

The depicting scans take several minutes (usually 10..20) - please be patient!

Usage

For more detailed description of the command line arguments see also the according section in the Wiki.

usage: open3e [-h] [@argsfile] [-c CAN] [-d DOIP] [-dev DEV] [-a] [-r READ] [-raw] [-w WRITE] [-f77] [-t TIMESTEP] [-m MQTT] [-mfstr MQTTFORMATSTRING] [-muser MQTTUSER:PASSW] [-mcid mqtt-client-id] [-j] [-v] [-l CMND-TOPIC] [-tx ECUADDR] [-cnfg DEVICES.JSON]

options:
-h, --help              show this help message and exit
-c CAN, --can CAN       use can device, e.g. can0
-d DOIP, --doip DOIP    use doip access, e.g. 192.168.1.1
-dev DEV, --dev DEV     boiler type --dev vdens or --dev vcal || pv/battery --dev vx3, --dev vair
-a, --scanall           dump all dids
-r READ, --read READ    read did, e.g. 0x173,0x174
-raw, --raw             return raw data for all dids
-w WRITE, --write WRITE
                        write did, e.g. -w 396=D601 (raw data only!)
-f77, --forcesid77      force the use of serive 0x77 for writing of a did
-t TIMESTEP, --timestep TIMESTEP
                        read continuous with delay in s
-m MQTT, --mqtt MQTT  publish to server, e.g. 192.168.0.1:1883:topicname
-mfstr MQTTFORMATSTRING, --mqttformatstring MQTTFORMATSTRING
                        mqtt formatstring e.g. {ecuAddr:03X}_{device}_{didNumber:04d}_{didName}
-muser MQTTUSER:PASSW, --mqttuser MQTTUSER:PASSW
                        mqtt username:password
-mcid mqtt-client-id, --mqttclientid mqtt-client-id
                        set mqtt client id of open3e
-tx ECUADDR, --ecuaddr ECUADDR
                        sets the default ECU Address different from 0x680
-cnfg DEVICES.JSON, --config DEVICES.JSON 
                        use multi-ECU configuration file, e.g. `devices.json` created by Open3E_depictSystem
-j, --json              send JSON structure via MQTT
-v, --verbose           verbose info
-l, --listen            mqtt topic to listen for commands, e.g. `open3e/cmnd`
@argsfile               use arguments given in a file. Seperate line for each argument.

Read dids

open3e -c can0 -dev vdens -r 268 -v
268 FlowTempSensor 27.2

open3e -c can0 -dev vcal -r 318 -v
318 WaterPressureSensor 1.8

open3e -c can0 -dev vcal -r 377 -v
377 IdentNumber 7XXXXXXXXXXXXX

open3e -c can0 -dev vcal -r 1043 -v
1043 FlowMeterSensor 2412.0

open3e -c can0 -dev vx3 -r 1664 -v
1664 ElectricalEnergyStorageStateOfCharge 44

open3e @myargs
    with content of file myargs:
    -c
    can0
    -dev
    vx3
    -r
    1664
    -v

Interval Readout

open3e -c can0 -dev vcal -r 1043 -t 1
2412.0
2413.0
2411.0
2412.0
...

Write did

Using raw data format

open3e -c can0 -dev vdens -raw -w 396=D601
-> sets domestic hot water setpoint to 47degC

Using json data format

open3e -c can0 -dev vdens -w 396='47.5'
-> sets domestic hot water setpoint to 47.5degC

open3e -c can0 -dev vdens -w 538='{"Mode": 1, "State": 0}'
-> sets ExternalDomesticHotWaterTargetOperationMode.Mode to 1 and .State to 0
-> Use -j -r to read data point in json format as template for writing. Always provide valid and complete json data for writing, enclosed in single quotes.

Extended writing service (internal can bus only, experimental)

In case of a "negative response" code when writing data, you may try to use the command line option -f77. However, this is experimental. Always verify the result!

Publish data points to mqtt

open3e -c can0 -dev vcal -r 268,269,271,274,318,1043 -m 192.168.0.5:1883:open3e -t 1
-> will periodically scan data points and publish data to broker 192.168.0.5

open3e -c can0 -dev vcal -r 268,269,271,274,318,1043 -m 192.168.0.5:1883:open3e -t 1 -mfstr "{didNumber}_{didName}"
-> will publish with custom identifier format: e.g. open3e/268_FlowTemperatureSensor

Listener mode

open3e -c can0 -dev vcal -m 192.168.0.5:1883:open3e -mfstr "{didNumber}_{didName}" -l open3e/cmnd

will listen for commands on topic open3e/cmnd with payload in json format:
{"mode":"read"|"read-raw"|"read-pure"|"read-all"|"write"|"write-raw", "data":[list of data], "addr":"ECU_addr"}
rem: "addr" is optional, otherwise defaut ECU address used

to read dids 271 and 274:
{"mode": "read", "data":[271,274]}

to read dids 265 and 266 as JSON-objects (even w/o option -json):
{"mode": "read-json", "data":[265,266]}

to read dids 265 and 266 as raw data (even w/o option -raw):
{"mode": "read-raw", "data":[265,266]}

to write value of 21.5 to did 395 and value of 45.0 to did 396:
{"mode": "write", "data":[[395,21.5],[396,45.0]]}

to write value of 45.0 to did 396 using service 0x77 (internal can bus only, experimental):
{"mode": "write-sid77", "data":[[396,45.0]]}

to write value of 45.0 to did 396 in raw data format using service 0x77 (internal can bus only, experimental):
{"mode": "write-raw-sid77", "data":[[396,"C201"]]}

to set frost protect threshold to -9°C in complex did
(A6FF lsb..msb -> 0xFFA6 -> -90 -> -9.0°C; Byte 0 unchanged):
{"mode": "write-raw", "data":[[2855,"01A6FF"]]}

to set frost protect threshold and eco function threshold to -9°C (complex dids):
{"mode": "write-raw", "data":[[2855,"01A6FF"],[2426,"01A6FF000A00"]]}


Option -m is mandatory for this mode.
Options -r, -t, -j, -v may be used in parallel.

Convert list of data points to json format

Use

open3e_dids2json

to convert common list of data points (Open3Edatapoints.py) to json format. A white list of writable data points is also created by this tool.

For developers

If you want to work on the codebase you can clone the repository and work in "editable" mode as follows. The editable mode allows you to modify and test changes in the source code without the need of a re-installation.

git clone https://github.com/open3e/open3e.git  
cd open3e
pip install --editable .[dev]

Hint: If you get an error like "A "pyproject.toml" file was found, but editable mode currently requires a setup.py based build." you are running an old pip version. Editable mode requires pip version >= 21.1.

About

connects E3 (vcal, vdens, vx3...) controller through can uds or doip

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • Python 100.0%