Revert "Sync Marlin Base (#2)"

This reverts commit 22bfe65.
StJa · Mar 9, 2020 · 0fd0091 · 0fd0091
1 parent 22bfe65
commit 0fd0091
Show file tree

Hide file tree

Showing 1,046 changed files with 4,569 additions and 6,914 deletions.
diff --git a/.editorconfig b/.editorconfig
diff --git a/.github/workflows/test-builds.yml b/.github/workflows/test-builds.yml
@@ -32,7 +32,6 @@ jobs:
         - megaatmega2560
         - teensy31
         - teensy35
-        - SAMD51_grandcentral_m4
 
         # Extended AVR Environments
 
@@ -76,6 +75,7 @@ jobs:
         #- mks_robin_lite
         #- mks_robin_mini
         #- mks_robin_nano
+        #- SAMD51_grandcentral_m4
 
     steps:
 

diff --git a/.gitignore b/.gitignore
@@ -1,6 +1,6 @@
 #
 # Marlin 3D Printer Firmware
-# Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+# Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 #
 # Based on Sprinter and grbl.
 # Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
@@ -146,9 +146,6 @@ Marlin/*/*/readme.txt
 Marlin/*/*/*/readme.txt
 Marlin/*/*/*/*/readme.txt
 
-# Secure Credentials
-Configuration_Secure.h
-
 #Visual Studio
 *.sln
 *.vcxproj

diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
@@ -1,6 +1,6 @@
 /**
  * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
  * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
@@ -36,7 +36,7 @@
  * Advanced settings can be found in Configuration_adv.h
  *
  */
-#define CONFIGURATION_H_VERSION 020004
+#define CONFIGURATION_H_VERSION 020000
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -784,8 +784,6 @@
   #define DEFAULT_YJERK 10.0
   #define DEFAULT_ZJERK  0.3
 
-  //#define TRAVEL_EXTRA_XYJERK 0.0     // Additional jerk allowance for all travel moves
-
   //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
   #if ENABLED(LIMITED_JERK_EDITING)
     #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
@@ -1067,14 +1065,12 @@
 
 // @section homing
 
-//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
-
-//#define UNKNOWN_Z_NO_RAISE      // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
+//#define NO_MOTION_BEFORE_HOMING  // Inhibit movement until all axes have been homed
 
-//#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
-                                  // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
+//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_AFTER_HOMING  10      // (mm) Height to move to after homing Z
+//#define Z_HOMING_HEIGHT 4  // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
@@ -1236,7 +1232,6 @@
     #define MESH_TEST_HOTEND_TEMP  205    // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
     #define MESH_TEST_BED_TEMP      60    // (°C) Default bed temperature for the G26 Mesh Validation Tool.
     #define G26_XY_FEEDRATE         20    // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
-    #define G26_RETRACT_MULTIPLIER   1.0  // G26 Q (retraction) used by default between mesh test elements.
   #endif
 
 #endif
@@ -1316,10 +1311,10 @@
 //#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
-  #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
-  #define LEVEL_CORNERS_HEIGHT      0.0   // (mm) Z height of nozzle at leveling points
-  #define LEVEL_CORNERS_Z_HOP       4.0   // (mm) Z height of nozzle between leveling points
-  //#define LEVEL_CENTER_TOO              // Move to the center after the last corner
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
+  #define LEVEL_CORNERS_HEIGHT 0.0  // (mm) Z height of nozzle at leveling points
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
 #endif
 
 /**

diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
@@ -1,6 +1,6 @@
 /**
  * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
  * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
@@ -31,7 +31,7 @@
  * Basic settings can be found in Configuration.h
  *
  */
-#define CONFIGURATION_ADV_H_VERSION 020004
+#define CONFIGURATION_ADV_H_VERSION 020000
 
 // @section temperature
 
@@ -668,54 +668,35 @@
  */
 //#define Z_STEPPER_AUTO_ALIGN
 #if ENABLED(Z_STEPPER_AUTO_ALIGN)
-  // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
-  // If not defined, probe limits will be used.
-  // Override with 'M422 S<index> X<pos> Y<pos>'
-  //#define Z_STEPPER_ALIGN_XY { {  10, 190 }, { 100,  10 }, { 190, 190 } }
-
-  /**
-   * Orientation for the automatically-calculated probe positions.
-   * Override Z stepper align points with 'M422 S<index> X<pos> Y<pos>'
-   *
-   * 2 Steppers:  (0)     (1)
-   *               |       |   2   |
-   *               | 1   2 |       |
-   *               |       |   1   |
-   *
-   * 3 Steppers:  (0)     (1)     (2)     (3)
-   *               |   3   | 1     | 2   1 |     2 |
-   *               |       |     3 |       | 3     |
-   *               | 1   2 | 2     |   3   |     1 |
-   *
-   * 4 Steppers:  (0)     (1)     (2)     (3)
-   *               | 4   3 | 1   4 | 2   1 | 3   2 |
-   *               |       |       |       |       |
-   *               | 1   2 | 2   3 | 3   4 | 4   1 |
-   *
-   */
-  #ifndef Z_STEPPER_ALIGN_XY
-    //#define Z_STEPPERS_ORIENTATION 0
-  #endif
+  // Define probe X and Y positions for Z1, Z2 [, Z3]
+  #define Z_STEPPER_ALIGN_XY { {  10, 190 }, { 100,  10 }, { 190, 190 } }
 
   // Provide Z stepper positions for more rapid convergence in bed alignment.
-  // Requires triple stepper drivers (i.e., set NUM_Z_STEPPER_DRIVERS to 3)
+  // Currently requires triple stepper drivers.
   //#define Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS
   #if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS)
     // Define Stepper XY positions for Z1, Z2, Z3 corresponding to
     // the Z screw positions in the bed carriage.
     // Define one position per Z stepper in stepper driver order.
     #define Z_STEPPER_ALIGN_STEPPER_XY { { 210.7, 102.5 }, { 152.6, 220.0 }, { 94.5, 102.5 } }
   #else
-    // Amplification factor. Used to scale the correction step up or down in case
-    // the stepper (spindle) position is farther out than the test point.
-    #define Z_STEPPER_ALIGN_AMP 1.0       // Use a value > 1.0 NOTE: This may cause instability!
+    // Amplification factor. Used to scale the correction step up or down.
+    // In case the stepper (spindle) position is further out than the test point.
+    // Use a value > 1. NOTE: This may cause instability
+    #define Z_STEPPER_ALIGN_AMP 1.0
   #endif
 
+  // Set number of iterations to align
+  #define Z_STEPPER_ALIGN_ITERATIONS 3
+
+  // Enable to restore leveling setup after operation
+  #define RESTORE_LEVELING_AFTER_G34
+
   // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
-  #define G34_MAX_GRADE              5    // (%) Maximum incline that G34 will handle
-  #define Z_STEPPER_ALIGN_ITERATIONS 5    // Number of iterations to apply during alignment
-  #define Z_STEPPER_ALIGN_ACC        0.02 // Stop iterating early if the accuracy is better than this
-  #define RESTORE_LEVELING_AFTER_G34      // Restore leveling after G34 is done?
+  #define G34_MAX_GRADE  5  // (%) Maximum incline G34 will handle
+
+  // Stop criterion. If the accuracy is better than this stop iterating early
+  #define Z_STEPPER_ALIGN_ACC 0.02
 #endif
 
 // @section motion
@@ -840,8 +821,8 @@
 
   // Define the pin to read during calibration
   #ifndef CALIBRATION_PIN
-    //#define CALIBRATION_PIN -1            // Define here to override the default pin
-    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the custom pin
+    #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop
+    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -1044,7 +1025,7 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
+    //#define POWER_LOSS_PIN         44 // Pin to detect power loss
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
@@ -1172,16 +1153,18 @@
   // Add an optimized binary file transfer mode, initiated with 'M28 B1'
   //#define BINARY_FILE_TRANSFER
 
-  /**
-   * Set this option to one of the following (or the board's defaults apply):
-   *
-   *           LCD - Use the SD drive in the external LCD controller.
-   *       ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
-   *  CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
-   *
-   * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
-   */
-  //#define SDCARD_CONNECTION LCD
+  #if HAS_SDCARD_CONNECTION
+    /**
+     * Set this option to one of the following (or the board's defaults apply):
+     *
+     *           LCD - Use the SD drive in the external LCD controller.
+     *       ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
+     *  CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
+     *
+     * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
+     */
+    //#define SDCARD_CONNECTION LCD
+  #endif
 
 #endif // SDSUPPORT
 
@@ -1258,7 +1241,6 @@
   #define STATUS_HOTEND_ANIM          // Use a second bitmap to indicate hotend heating
   #define STATUS_BED_ANIM             // Use a second bitmap to indicate bed heating
   #define STATUS_CHAMBER_ANIM         // Use a second bitmap to indicate chamber heating
-  //#define STATUS_CUTTER_ANIM        // Use a second bitmap to indicate spindle / laser active
   //#define STATUS_ALT_BED_BITMAP     // Use the alternative bed bitmap
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
@@ -1332,11 +1314,9 @@
   //#define AO_EXP1_PINMAP    // AlephObjects CLCD UI EXP1 mapping
   //#define AO_EXP2_PINMAP    // AlephObjects CLCD UI EXP2 mapping
   //#define CR10_TFT_PINMAP   // Rudolph Riedel's CR10 pin mapping
-  //#define S6_TFT_PINMAP     // FYSETC S6 pin mapping
-
   //#define OTHER_PIN_LAYOUT  // Define pins manually below
   #if ENABLED(OTHER_PIN_LAYOUT)
-    // Pins for CS and MOD_RESET (PD) must be chosen
+    // The pins for CS and MOD_RESET (PD) must be chosen.
     #define CLCD_MOD_RESET  9
     #define CLCD_SPI_CS    10
 
@@ -1446,7 +1426,6 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
@@ -1575,7 +1554,7 @@
 
   // Add additional compensation depending on hotend temperature
   // Note: this values cannot be calibrated and have to be set manually
-  #if ENABLED(PROBE_TEMP_COMPENSATION)
+  #ifdef PROBE_TEMP_COMPENSATION
     // Max temperature that can be reached by heated bed.
     // This is required only for the calibration process.
     #define PTC_MAX_BED_TEMP 110
@@ -2786,12 +2765,6 @@
  */
 #define FASTER_GCODE_PARSER
 
-#if ENABLED(FASTER_GCODE_PARSER)
-  //#define GCODE_QUOTED_STRINGS  // Support for quoted string parameters
-#endif
-
-//#define GCODE_CASE_INSENSITIVE  // Accept G-code sent to the firmware in lowercase
-
 /**
  * CNC G-code options
  * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc.
@@ -3031,19 +3004,11 @@
 //#define ESP3D_WIFISUPPORT   // ESP3D Library WiFi management (https://github.com/luc-github/ESP3DLib)
 
 #if EITHER(WIFISUPPORT, ESP3D_WIFISUPPORT)
+  #define WIFI_SSID "Wifi SSID"
+  #define WIFI_PWD  "Wifi Password"
   //#define WEBSUPPORT          // Start a webserver (which may include auto-discovery)
   //#define OTASUPPORT          // Support over-the-air firmware updates
   //#define WIFI_CUSTOM_COMMAND // Accept feature config commands (e.g., WiFi ESP3D) from the host
-
-  /**
-   * To set a default WiFi SSID / Password, create a file called Configuration_Secure.h with
-   * the following defines, customized for your network. This specific file is excluded via
-   * .gitignore to prevent it from accidentally leaking to the public.
-   *
-   *   #define WIFI_SSID "WiFi SSID"
-   *   #define WIFI_PWD  "WiFi Password"
-   */
-  //#include "Configuration_Secure.h" // External file with WiFi SSID / Password
 #endif
 
 /**