Skip to content

An open hardware reference design of a 500 W integrated propeller drive based on the Mitochondrik LV motor control chip. It includes a motor and its control electronics in a single compact unit.

License

Notifications You must be signed in to change notification settings

Zubax/newtdrive_nd500_34v

Repository files navigation

NewtDrive ND500-34V / Zubax Sadulli

Sadulli is an open-hardware reference design of a 500 W integrated propeller drive based on the Mitochondrik LV motor control chip. It includes a motor and its control electronics in a single compact unit.

The main design goal is to create a compact yet sophisticated motor controller that can be integrated with relatively small BLDC and PMSM motors (about 40-45 mm in diameter) in a single unit. Being equipped with a standard mounting hole pattern, Sadulli can be used as a drop-in replacement for regular standalone motors in various UAV applications.

Specifications

  • Operating voltage range: 4-8S Li-ion LiCoO2, 11-34 V
  • Maximum continuous power 500 W
  • Maximum continuous phase current amplitude 40 A
  • Cyphal/CAN (formerly UAVCAN) interface compatible with the DS-015 drone standard
  • Solderless integration

Sadulli consists of two main parts: a COTS motor and the ESC. This repository contains the ESC hardware source files only. There are two design variants of the Sadulli drive. All of them share the same ESC design.

Variant Motor Propeller diameter [inch] Propeller pitch [inch] Mass [g]
Alakdan Scorpion MII-4010 17 6.2 193
Nudo N/A N/A N/A 62
Alakdan Nudo

Sadulli is equipped with a single non-redundant Cyphal/CAN interface. The input power is supplied through a standard XT30 male connector. The device can deliver 5V to the Cyphal/CAN power delivery network if the respective configuration option is enabled.

Under the hood, Sadulli is a construction of three PCBs (excluding the Mitochondrik).

Sadulli PCB

The main PCB that determines most of Sadulli's properties is the power stage PCB. The power stage is composed of three BUK9K6R2-40E MOSFET arrays.

Parameter Value
Drain to Source Voltage (Vds) 40 V
Current - Continuous Drain (Id) @ 25°C 40 A
Rds on (Max) @ Id, Vgs 6 mOhm @ 25 A, 10 V
Gate Charge (Qg) (Max) @ Vgs 35.4 nC @ 10 V

The resistance of the phase current shunts is 3 mOhm.

The bulk capacitor bank is formed with 6 68µF aluminum electrolytic capacitors.

Telega configuration

The Mitochondrik LV module installed in Sadulli needs to be configured such that it is aware of the parameters of the power stage (and the motor). To achieve this, upload the following configuration:

# Refer to the Mitochondrik-LV datasheet for the explanation of how the parameter values have been found.
vsi.bridge_resistance:    [0.003, 0.006, 0.003, 0.006, 0.003, 0.003]                            # [ohm]
vsi.phase_current_gain:   [33.333333333333, 33.333333333333, 8.333333333333, 8.333333333333]    # [ampere/volt]
vsi.phase_current_stderr: [0.2, 0.2, 0.1, 0.1]                                                  # [ampere]
vsi.thermistor_v2k:       [223.15, 100.0, 0.0]                                                  # for MCP9700

motor.current_ctl_bwr:  0.04
motor.current_max:      38.0
motor.mechanical_ratio: 7                   # The motor has 14 poles.
motor.inductance_dq:    [29.0e-6, 29.0e-6]
motor.resistance:       0.0508
motor.flux_linkage:     0.002115
motor.current_ramp:     5000.0
motor.voltage_ramp:     20.0
# The thermistor coefficients are valid for:
# R_pull = 1.2 kohms; R_io = 0; V_pull = 3.3 V
# Thermistor models: KTY81/120, KTY81/110, KTY81/121, KTY81/122, KTY81/150, 102PS1J, 102PS1G.
motor.thermistor_v2k: [151.24172662, 36.46076996, 40.65372514]

aux.pull: +1                    # Pull up the thermistor input.

sys.debug: false                # Turn off the in-circuit debug interfaces to enhance EMI immunity.
sys.golden: sys. vsi. motor. aux.pull # Retain these parameter groups across a factory reset.

Refer to the Telega Reference Manual for details.

Release notes

Sadulli v1.5 (May 2023)

  • Added Alakdan variant using Scorpion MII-4010 motor.
  • Removed Grosso and Piccino variants using SunnySky motors.
  • Updated assembly guide.
  • Increased the hardware over-current protection limit (R1 on the connectors PCB increased to 27k).
  • Added thermistor alternatives:
Original Alternatives
KTY81/120 KTY81/110, KTY81/121, KTY81/122, KTY81/150, 102PS1J, 102PS1G

Sadulli v1.0 (January 2021)

First stable release. There have been no substantial changes compared to the pre-production revision.

License

This project is licensed under the terms of CC-BY 4.0.

About

An open hardware reference design of a 500 W integrated propeller drive based on the Mitochondrik LV motor control chip. It includes a motor and its control electronics in a single compact unit.

Resources

License

Stars

Watchers

Forks

Packages

No packages published