update example info

.vscode/settings.json

@@ -4,13 +4,16 @@
         "CKSUM",
         "HCHO",
         "HWSERIAL",
+        "Hzatmega",
         "MCU",
         "PMSA",
         "PMSerial",
         "Plantower",
         "SERIALPM",
         "UART",
         "USART",
+        "atmelavr",
+        "atmelsam",
         "bluepill",
         "chlen",
         "datasheet",
@@ -24,6 +27,8 @@
         "nbin",
         "rhum",
         "samd",
+        "stlink",
+        "ststm",
         "uint"
     ]
 }

README.md

@@ -61,7 +61,7 @@ The sensor type inference does not cover the `PMS5003S` and `PMS5003T` variants,
 
 ### PMSx003 on HardwareSerial
 
-```arduino
+```c++
 #include <PMserial.h>
 SerialPM pms(PMSx003, Serial);  // PMSx003, UART
 
@@ -83,7 +83,7 @@ Setup for different MCU is covered on the [HardwareSerial][] example.
 
 ### PMSx003 on SoftwareSerial
 
-```arduino
+```c++
 #include <PMserial.h>
 SerialPM pms(PMSx003, 10, 11);  // PMSx003, RX, TX
 
@@ -108,30 +108,30 @@ Setup for different MCU is covered on the [SoftwareSerial][] example.
 On some ESP32 boards Serial1 default pins are connected to the flash.
 Using the standard constructor will cause a crash, see [espressif/arduino-esp32#148](https://github.com/espressif/arduino-esp32/issues/148).
 
-```Arduino
+```c++
 // will crash the ESP32
 SerialPM pms(PMSx003, Serial1);
-````
+```
 
 Fortunately, it is possible to define alternative for pins by calling:
 
-```Arduino
+```c++
 // define Serial1 pins
 Serial1.begin(9600, SERIAL_8N1, <RX>, <TX>);
 ```
 
 The PMSerial library uses this feature to implement the flexibility of SoftwareSerial
 
-```Arduino
+```c++
 // define Serial1 pins
 SerialPM pms(PMSx003, <RX>, <TX>);
-````
+```
 
 The [SoftwareSerial example][esp32hw] uses Serial1 on pins 23 (RX) and 19 (TX).
 The [HardwareSerial example][esp32hw] uses Serial2.
 
-[esp32hw]: examples/HardwareSerial/README.md#mhetesp32minikit
-[esp32sw]: examples/SoftwareSerial/README.md#mhetesp32minikit
+[esp32hw]: examples/HardwareSerial/README.md#esp32-minikit
+[esp32sw]: examples/SoftwareSerial/README.md#esp32-minikit
 
 ## Advanced usage
 
@@ -215,7 +215,7 @@ The available status/error codes and pre-defined error messages are:
 For easy of use, the error message are pre-defined with `#define`.
 See the [examples](examples/) for error handling implementation.
 
-## Contribute back
+## Contribute
 
 If you have read this far, this is the library for your project
 or you can not figure out how to use it. In any case, I can use your help.

examples/HardwareSerial/README.md

@@ -2,13 +2,21 @@
 
 Read PMS5003 sensor on Serial/Serial1/Serial2, depending on the board.
 
-## Arduino `leonardo`
+## [Arduino Leonardo](https://docs.platformio.org/en/latest/boards/atmelavr/leonardo.html)
 
 **Note** This is a 5V board, and the PMS5003 RX/TX pins are 3.3V.
 You need to add a logic level converter, or use a 3.3V version of this board.
 
 - Serial1 on pins 0 (RX) and 1 (TX).
 
+```ini
+[env:leonardo]
+framework = arduino
+platform = atmelavr
+board = leonardo
+build_flags = -D USE_HWSERIAL1
+```
+
 ```bash
 # compile
 platformio run -e leonardo
@@ -20,7 +28,7 @@ platformio run -e leonardo -t upload
 platformio run -e leonardo -t monitor
 ```
 
-## Arduino `mega2560`
+## [Arduino Mega 2560](https://docs.platformio.org/en/latest/boards/atmelavr/megaatmega2560.html)
 
 **Note** This is a 5V board, and the PMS5003 RX/TX pins are 3.3V.
 You need to add a logic level converter, or use a 3.3V version of this board.
@@ -31,6 +39,14 @@ You need to add a logic level converter, or use a 3.3V version of this board.
 
 This example uses Serial1.
 
+```ini
+[env:mega2560]
+framework = arduino
+platform = atmelavr
+board = megaatmega2560
+build_flags = -D USE_HWSERIAL1
+```
+
 ```bash
 # compile
 platformio run -e mega2560
@@ -42,7 +58,7 @@ platformio run -e mega2560 -t upload
 platformio run -e mega2560 -t monitor
 ```
 
-## STM32 `genericSTM32F103C8`
+## [STM32F103C8](https://docs.platformio.org/en/latest/boards/ststm32/genericSTM32F103C8.html)
 
 **Note** This is a 3.3V board, and the PMS5003 requires 5V.
 You need provide 5V for the fan to operate properly.
@@ -53,6 +69,15 @@ You need provide 5V for the fan to operate properly.
 
 This example uses Serial1.
 
+```ini
+[env:genericSTM32F103C8]
+framework = arduino
+platform = ststm32
+board = genericSTM32F103C8
+upload_protocol = stlink
+build_flags = -D USE_HWSERIAL1
+```
+
 ```bash
 # compile
 platformio run -e genericSTM32F103C8
@@ -64,7 +89,7 @@ platformio run -e genericSTM32F103C8 -t upload
 platformio run -e genericSTM32F103C8 -t monitor
 ```
 
-## STM32 `maple_mini`
+## [STM32 Maple Mini](https://docs.platformio.org/en/latest/boards/ststm32/maple_mini_b20.html)
 
 **Note** This is a 3.3V board, and the PMS5003 requires 5V.
 You need provide 5V for the fan to operate properly.
@@ -75,6 +100,14 @@ You need provide 5V for the fan to operate properly.
 
 This example uses Serial2.
 
+```ini
+[env:maple_mini]
+framework = arduino
+platform = ststm32
+board = maple_mini_b20
+build_flags = -D USE_HWSERIAL2
+```
+
 ```bash
 # compile
 platformio run -e maple_mini
@@ -86,7 +119,7 @@ platformio run -e maple_mini -t upload
 platformio run -e maple_mini -t monitor
 ```
 
-## ESP8266 `esp01`
+## [ESP8266 ESP-01 512k](https://docs.platformio.org/en/latest/boards/espressif8266/esp01.html)
 
 **Note** This is a 3.3V board, and the PMS5003 requires 5V.
 
@@ -96,6 +129,13 @@ This example used Serial for communicating with the sensor
 and printing the sensor values.
 Some garbage between printouts is to be expected.
 
+```ini
+[env:esp01]
+framework = arduino
+platform = espressif8266
+board = esp01
+```
+
 ```bash
 # compile
 platformio run -e esp01
@@ -107,7 +147,7 @@ platformio run -e esp01 -t upload
 platformio run -e esp01 -t monitor
 ```
 
-## ESP32 `mhetesp32minikit`
+## [ESP32 MiniKit](https://docs.platformio.org/en/latest/boards/espressif32/mhetesp32minikit.html)
 
 **Note** This is a 3.3V board, and the PMS5003 requires 5V.
 You need provide 5V for the fan to operate properly.
@@ -118,29 +158,37 @@ You need provide 5V for the fan to operate properly.
 On some ESP32 boards Serial1 default pins are connected to the flash.
 Using the standard constructor will cause a crash, see [espressif/arduino-esp32#148](https://github.com/espressif/arduino-esp32/issues/148).
 
-```Arduino
+```c++
 // will crash the ESP32
 SerialPM pms(PMSx003, Serial1);
-````
+```
 
 Fortunately, it is possible to define alternative for pins by calling:
 
-```Arduino
+```c++
 // define Serial1 pins
 Serial1.begin(9600, SERIAL_8N1, <RX>, <TX>);
 ```
 
 The PMSerial library uses this feature to implement the flexibility of SoftwareSerial
 
-```Arduino
+```c++
 // define Serial1 pins
 SerialPM pms(PMS5003, <RX>, <TX>);
-````
+```
 
 The [SoftwareSerial example][esp32sw] uses Serial1 on pins 23 (RX) and 19 (TX).
 This example uses Serial2.
 
-[esp32sw]: ../SoftwareSerial/README.md#mhetesp32minikit
+[esp32sw]: ../SoftwareSerial/README.md#esp32-minikit
+
+```ini
+[env:esp32minikit]
+framework = arduino
+platform = espressif32
+board = mhetesp32minikit
+build_flags = -D USE_HWSERIAL2
+```
 
 ```bash
 # compile
@@ -153,13 +201,21 @@ platformio run -e esp32minikit -t upload
 platformio run -e esp32minikit -t monitor
 ```
 
-## Arduino `mkrwifi1010`
+## [Arduino MKR WiFi 1010](https://docs.platformio.org/en/latest/boards/atmelsam/mkrwifi1010.html)
 
 **Note** This is a 3.3V board, and the PMS5003 requires 5V.
 You need provide 5V for the fan to operate properly.
 
 - Serial1 on pins 13 (RX) and 14 (TX).
 
+```ini
+[env:mkrwifi1010]
+framework = arduino
+platform = atmelsam
+board = mkrwifi1010
+build_flags = -D USE_HWSERIAL1
+```
+
 ```bash
 # compile
 platformio run -e mkrwifi1010
@@ -169,4 +225,4 @@ platformio run -e mkrwifi1010 -t upload
 
 # open serial monitor
 platformio run -e mkrwifi1010 -t monitor
-```
+```

examples/HardwareSerial/platformio.ini

@@ -44,7 +44,7 @@ build_flags = -D USE_HWSERIAL2
 platform = espressif8266
 board = esp01
 
-[env:mhetesp32minikit]
+[env:esp32minikit]
 platform = espressif32
 board = mhetesp32minikit
 build_flags = -D USE_HWSERIAL2