Network interface for Paradox alarm systems. Provides a bidirectional communication between a Paradox alarm system and MQTT. Reports all events as they occur. If logged in then it provides extra information about the system and can arm/disarm partitions through MQTT.
- SP5500
- SP6000
- SP7000
- MG5000
- MG5050
Flash latest release using a 3.3V serial adapter, connect to the created hot-spot (ESParadox_espid) and set it up using the web interface. Easy to mount inside the Paradox metal box (4 holes for mounting and 1 for the wifi antenna), simple 4 wire connection to the paradox main board.
home/alarm/ESParadox/...
- cmnd/arm - full arm
- cmnd/disarm - disarm
- cmnd/stay_arm - stay arm
- cmnd/sleep_arm - sleep arm
- cmnd/stay_arm_d - stay arm with Stay-D
- cmnd/sleep_arm_d - sleep arm with Stay-D
- cmnd/disarm_both - disarm both partitions, disable Stay-D
- cmnd/bypass - send as value zone number to bypass (0-31)
- cmnd/pgm_on_ow - PGM ON in overwrite mode
- cmnd/pgm_off_ow - PGM OFF in overwrite mode
- cmnd/pgm_on - PGM ON
- cmnd/pgm_off - PGM OFF
- cmnd/ - send json
JSON commands:
{"cmd":number, "scmd":number}- send command/subcommand, read manual{"time":"set", "year":2020, "month":7, "day":31, "hour":15, "minute":33}- set date/time{"UserID":"0000", "UserPASS":"123456"}- set userid/password for panel login. First user is usually 0000 and password is the one you use on the panel for disarming. This command can be used in case you don't want to store it in ESP flash memory. Data must be sent as text! Password can be 4 or 6 characters long.{"update":any}- perform update{"reset":any}- perform ESP restart{"disconnect":any}- log out from Paradox (does a log in immediately if continous panel reporting is selected)
- subscribe to home/alarm/ESParadox/arm for arm (1) / disarm (0) status
- publish to home/alarm/ESParadox/cmnd/AD value (1) for arm / (0) for disarm
home/alarm/ESParadox/....
-
panel/info - contains information about the mainboard
-
panel/values - AC voltage, DC voltage, Battery voltage, RF Noise floor (for RF capable mainboards)
-
event - contains the last reported event, date/time, event group, event subgroup, partition, sensor serial number, sensor label, event description
-
trouble - current trouble indicators
-
trouble/event - last trouble event decription
-
zone/open - array of open zones
-
zone/tamper - array of tampered zones
-
zone/fire - array of zones in fire alarm
-
zone/RF trouble - array of zones in RF trouble
-
zone/low battery - array of zones with low battery
-
zone/X - last event per zone number (X = 1 to 32)
-
zone/X/status - status per zone number
-
zone/X/signal - signal strength per zone number
-
zone/X/exit delay - of zone in exit delay (0/1)
-
zone/X/label - label for zone
-
zone/X/sn - serial number of device
-
pgm/tamper - array of tampered pgms
-
pgm/RF trouble - array of pgms in RF trouble
-
pgm/X/signal - signal strength per pgm number (X = 1 to 16)
-
module/tamper - array of tampered modules
-
module/supervision - array of modules that lost supervision (in trouble)
-
repeater/supervision - array of repeaters that lost supervision
-
repeater/AC lost - array of repeaters that lost AC power
-
repeater/battery failure - array of repeaters that have a bad battery
-
repeater/X/signal - signal strength per repeater number (X = 1 to 2)
-
keypad/supervision - array of keypads that lost supervision
-
keypad/AC lost - array of keypads that lost AC power
-
keypad/battery failure - array of keypads that have a bad battery
-
keypad/X/signal - signal strength per keypad number (X = 1 to 8)
-
partition/X - last event per partition number (X = 1 or 2)
-
partition/X/status - current partition status
-
arm - shows current arm/disarm status (1 = arm, 0 = disarm)
-
bell - last bell event description
You can build the project yourself using the Arduino IDE. Needed libraries are linked below. Or even better using PlatformIO, libraries are taken care of automatically.
Roll your own using the provided schematics or buy one as PCB, kit or fully assembled from https://3dstar.ro/proiecte/esparadox.
