Bluetooth: btintel_pcie: Add handshake between driver and firmware

The following handshake mechanism needs be followed after firmware
download is completed to bring the firmware to running state.

After firmware fragments of Operational image are downloaded and
secure sends result of the image succeeds,

1. Driver sends HCI Intel reset with boot option #1 to switch FW image.
2. FW sends Alive GP[0] MSIx
3. Driver enables data path (doorbell 0x460 for RBDs, etc...)
4. Driver gets Bootup event from firmware
5. Driver performs D0 entry to device (WRITE to IPC_Sleep_Control =0x0)
6. FW sends Alive GP[0] MSIx
7. Device host interface is fully set for BT protocol stack operation.
8. Driver may optionally get debug event with ID 0x97 which can be dropped

For Intermediate loadger image, all the above steps are applicable
expcept #5 and #6.

On HCI_OP_RESET, firmware raises alive interrupt. Driver needs to wait
for it before passing control over to bluetooth stack.

Co-developed-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

drivers/bluetooth/btintel.c

@@ -1841,6 +1841,37 @@ static int btintel_boot_wait(struct hci_dev *hdev, ktime_t calltime, int msec)
 	return 0;
 }
 
+static int btintel_boot_wait_d0(struct hci_dev *hdev, ktime_t calltime,
+				int msec)
+{
+	ktime_t delta, rettime;
+	unsigned long long duration;
+	int err;
+
+	bt_dev_info(hdev, "Waiting for device transition to d0");
+
+	err = btintel_wait_on_flag_timeout(hdev, INTEL_WAIT_FOR_D0,
+					   TASK_INTERRUPTIBLE,
+					   msecs_to_jiffies(msec));
+	if (err == -EINTR) {
+		bt_dev_err(hdev, "Device d0 move interrupted");
+		return -EINTR;
+	}
+
+	if (err) {
+		bt_dev_err(hdev, "Device d0 move timeout");
+		return -ETIMEDOUT;
+	}
+
+	rettime = ktime_get();
+	delta = ktime_sub(rettime, calltime);
+	duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+	bt_dev_info(hdev, "Device moved to D0 in %llu usecs", duration);
+
+	return 0;
+}
+
 static int btintel_boot(struct hci_dev *hdev, u32 boot_addr)
 {
 	ktime_t calltime;
@@ -1849,6 +1880,7 @@ static int btintel_boot(struct hci_dev *hdev, u32 boot_addr)
 	calltime = ktime_get();
 
 	btintel_set_flag(hdev, INTEL_BOOTING);
+	btintel_set_flag(hdev, INTEL_WAIT_FOR_D0);
 
 	err = btintel_send_intel_reset(hdev, boot_addr);
 	if (err) {
@@ -1861,13 +1893,28 @@ static int btintel_boot(struct hci_dev *hdev, u32 boot_addr)
 	 * is done by the operational firmware sending bootup notification.
 	 *
 	 * Booting into operational firmware should not take longer than
-	 * 1 second. However if that happens, then just fail the setup
+	 * 5 second. However if that happens, then just fail the setup
 	 * since something went wrong.
 	 */
-	err = btintel_boot_wait(hdev, calltime, 1000);
-	if (err == -ETIMEDOUT)
+	err = btintel_boot_wait(hdev, calltime, 5000);
+	if (err == -ETIMEDOUT) {
 		btintel_reset_to_bootloader(hdev);
+		goto exit_error;
+	}
 
+	if (hdev->bus == HCI_PCI) {
+		/* In case of PCIe, after receiving bootup event, driver performs
+		 * D0 entry by writing 0 to sleep control register (check
+		 * btintel_pcie_recv_event())
+		 * Firmware acks with alive interrupt indicating host is full ready to
+		 * perform BT operation. Lets wait here till INTEL_WAIT_FOR_D0
+		 * bit is cleared.
+		 */
+		calltime = ktime_get();
+		err = btintel_boot_wait_d0(hdev, calltime, 2000);
+	}
+
+exit_error:
 	return err;
 }
 
@@ -3273,7 +3320,7 @@ int btintel_configure_setup(struct hci_dev *hdev, const char *driver_name)
 }
 EXPORT_SYMBOL_GPL(btintel_configure_setup);
 
-static int btintel_diagnostics(struct hci_dev *hdev, struct sk_buff *skb)
+int btintel_diagnostics(struct hci_dev *hdev, struct sk_buff *skb)
 {
 	struct intel_tlv *tlv = (void *)&skb->data[5];
 
@@ -3302,6 +3349,7 @@ static int btintel_diagnostics(struct hci_dev *hdev, struct sk_buff *skb)
 recv_frame:
 	return hci_recv_frame(hdev, skb);
 }
+EXPORT_SYMBOL_GPL(btintel_diagnostics);
 
 int btintel_recv_event(struct hci_dev *hdev, struct sk_buff *skb)
 {

drivers/bluetooth/btintel.h

@@ -178,6 +178,7 @@ enum {
 	INTEL_ROM_LEGACY,
 	INTEL_ROM_LEGACY_NO_WBS_SUPPORT,
 	INTEL_ACPI_RESET_ACTIVE,
+	INTEL_WAIT_FOR_D0,
 
 	__INTEL_NUM_FLAGS,
 };
@@ -249,6 +250,7 @@ int btintel_bootloader_setup_tlv(struct hci_dev *hdev,
 int btintel_shutdown_combined(struct hci_dev *hdev);
 void btintel_hw_error(struct hci_dev *hdev, u8 code);
 void btintel_print_fseq_info(struct hci_dev *hdev);
+int btintel_diagnostics(struct hci_dev *hdev, struct sk_buff *skb);
 #else
 
 static inline int btintel_check_bdaddr(struct hci_dev *hdev)
@@ -382,4 +384,9 @@ static inline void btintel_hw_error(struct hci_dev *hdev, u8 code)
 static inline void btintel_print_fseq_info(struct hci_dev *hdev)
 {
 }
+
+static inline int btintel_diagnostics(struct hci_dev *hdev, struct sk_buff *skb)
+{
+	return -EOPNOTSUPP;
+}
 #endif