🏗️ Support for up to 6 linear axes (MarlinFirmware#19112)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

Marlin/Configuration.h

@@ -35,7 +35,7 @@
  *
  * Advanced settings can be found in Configuration_adv.h
  */
-#define CONFIGURATION_H_VERSION 02000801
+#define CONFIGURATION_H_VERSION 02000900
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -66,6 +66,14 @@
 //
 //===========================================================================
 
+//===========================================================================
+//=========================== FOAMCUTTER_XYUV ==============================
+//===========================================================================
+// For a hot wire cutter with parallel horizontal axes X, I where the hights
+// of the two wire ends are controlled by parallel axes Y, J.
+//
+//#define FOAMCUTTER_XYUV
+
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -149,6 +157,45 @@
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
 
+/**
+ * Define the number of coordinated linear axes.
+ * See https://github.com/DerAndere1/Marlin/wiki
+ * Each linear axis gets its own stepper control and endstop:
+ *
+ *   Steppers: *_STEP_PIN, *_ENABLE_PIN, *_DIR_PIN, *_ENABLE_ON
+ *   Endstops: *_STOP_PIN, USE_*MIN_PLUG, USE_*MAX_PLUG
+ *       Axes: *_MIN_POS, *_MAX_POS, INVERT_*_DIR
+ *    Planner: DEFAULT_AXIS_STEPS_PER_UNIT, DEFAULT_MAX_FEEDRATE
+ *             DEFAULT_MAX_ACCELERATION, AXIS_RELATIVE_MODES,
+ *             MICROSTEP_MODES, MANUAL_FEEDRATE
+ *
+ * :[3, 4, 5, 6]
+ */
+//#define LINEAR_AXES 3
+
+/**
+ * Axis codes for additional axes:
+ * This defines the axis code that is used in G-code commands to
+ * reference a specific axis.
+ * 'A' for rotational axis parallel to X
+ * 'B' for rotational axis parallel to Y
+ * 'C' for rotational axis parallel to Z
+ * 'U' for secondary linear axis parallel to X
+ * 'V' for secondary linear axis parallel to Y
+ * 'W' for secondary linear axis parallel to Z
+ * Regardless of the settings, firmware-internal axis IDs are
+ * I (AXIS4), J (AXIS5), K (AXIS6).
+ */
+#if LINEAR_AXES >= 4
+  #define AXIS4_NAME 'A' // :['A', 'B', 'C', 'U', 'V', 'W']
+#endif
+#if LINEAR_AXES >= 5
+  #define AXIS5_NAME 'B' // :['A', 'B', 'C', 'U', 'V', 'W']
+#endif
+#if LINEAR_AXES >= 6
+  #define AXIS6_NAME 'C' // :['A', 'B', 'C', 'U', 'V', 'W']
+#endif
+
 // @section extruder
 
 // This defines the number of extruders
@@ -691,9 +738,15 @@
 #define USE_XMIN_PLUG
 #define USE_YMIN_PLUG
 #define USE_ZMIN_PLUG
+//#define USE_IMIN_PLUG
+//#define USE_JMIN_PLUG
+//#define USE_KMIN_PLUG
 //#define USE_XMAX_PLUG
 //#define USE_YMAX_PLUG
 //#define USE_ZMAX_PLUG
+//#define USE_IMAX_PLUG
+//#define USE_JMAX_PLUG
+//#define USE_KMAX_PLUG
 
 // Enable pullup for all endstops to prevent a floating state
 #define ENDSTOPPULLUPS
@@ -702,9 +755,15 @@
   //#define ENDSTOPPULLUP_XMAX
   //#define ENDSTOPPULLUP_YMAX
   //#define ENDSTOPPULLUP_ZMAX
+  //#define ENDSTOPPULLUP_IMAX
+  //#define ENDSTOPPULLUP_JMAX
+  //#define ENDSTOPPULLUP_KMAX
   //#define ENDSTOPPULLUP_XMIN
   //#define ENDSTOPPULLUP_YMIN
   //#define ENDSTOPPULLUP_ZMIN
+  //#define ENDSTOPPULLUP_IMIN
+  //#define ENDSTOPPULLUP_JMIN
+  //#define ENDSTOPPULLUP_KMIN
   //#define ENDSTOPPULLUP_ZMIN_PROBE
 #endif
 
@@ -715,19 +774,31 @@
   //#define ENDSTOPPULLDOWN_XMAX
   //#define ENDSTOPPULLDOWN_YMAX
   //#define ENDSTOPPULLDOWN_ZMAX
+  //#define ENDSTOPPULLDOWN_IMAX
+  //#define ENDSTOPPULLDOWN_JMAX
+  //#define ENDSTOPPULLDOWN_KMAX
   //#define ENDSTOPPULLDOWN_XMIN
   //#define ENDSTOPPULLDOWN_YMIN
   //#define ENDSTOPPULLDOWN_ZMIN
+  //#define ENDSTOPPULLDOWN_IMIN
+  //#define ENDSTOPPULLDOWN_JMIN
+  //#define ENDSTOPPULLDOWN_KMIN
   //#define ENDSTOPPULLDOWN_ZMIN_PROBE
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define I_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define J_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define K_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
@@ -756,6 +827,9 @@
 //#define Z2_DRIVER_TYPE A4988
 //#define Z3_DRIVER_TYPE A4988
 //#define Z4_DRIVER_TYPE A4988
+//#define I_DRIVER_TYPE  A4988
+//#define J_DRIVER_TYPE  A4988
+//#define K_DRIVER_TYPE  A4988
 #define E0_DRIVER_TYPE A4988
 //#define E1_DRIVER_TYPE A4988
 //#define E2_DRIVER_TYPE A4988
@@ -809,14 +883,14 @@
 /**
  * Default Axis Steps Per Unit (steps/mm)
  * Override with M92
- *                                      X, Y, Z, E0 [, E1[, E2...]]
+ *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
 #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
- *                                      X, Y, Z, E0 [, E1[, E2...]]
+ *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
 #define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
 
@@ -829,7 +903,7 @@
  * Default Max Acceleration (change/s) change = mm/s
  * (Maximum start speed for accelerated moves)
  * Override with M201
- *                                      X, Y, Z, E0 [, E1[, E2...]]
+ *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
 #define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
 
@@ -863,6 +937,9 @@
   #define DEFAULT_XJERK 10.0
   #define DEFAULT_YJERK 10.0
   #define DEFAULT_ZJERK  0.3
+  //#define DEFAULT_IJERK  0.3
+  //#define DEFAULT_JJERK  0.3
+  //#define DEFAULT_KJERK  0.3
 
   //#define TRAVEL_EXTRA_XYJERK 0.0     // Additional jerk allowance for all travel moves
 
@@ -1177,12 +1254,18 @@
 #define Y_ENABLE_ON 0
 #define Z_ENABLE_ON 0
 #define E_ENABLE_ON 0 // For all extruders
+//#define I_ENABLE_ON 0
+//#define J_ENABLE_ON 0
+//#define K_ENABLE_ON 0
 
 // Disable axis steppers immediately when they're not being stepped.
 // WARNING: When motors turn off there is a chance of losing position accuracy!
 #define DISABLE_X false
 #define DISABLE_Y false
 #define DISABLE_Z false
+//#define DISABLE_I false
+//#define DISABLE_J false
+//#define DISABLE_K false
 
 // Turn off the display blinking that warns about possible accuracy reduction
 //#define DISABLE_REDUCED_ACCURACY_WARNING
@@ -1198,6 +1281,9 @@
 #define INVERT_X_DIR false
 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
+//#define INVERT_I_DIR false
+//#define INVERT_J_DIR false
+//#define INVERT_K_DIR false
 
 // @section extruder
 
@@ -1233,6 +1319,9 @@
 #define X_HOME_DIR -1
 #define Y_HOME_DIR -1
 #define Z_HOME_DIR -1
+//#define I_HOME_DIR -1
+//#define J_HOME_DIR -1
+//#define K_HOME_DIR -1
 
 // @section machine
 
@@ -1247,6 +1336,12 @@
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
 #define Z_MAX_POS 200
+//#define I_MIN_POS 0
+//#define I_MAX_POS 50
+//#define J_MIN_POS 0
+//#define J_MAX_POS 50
+//#define K_MIN_POS 0
+//#define K_MAX_POS 50
 
 /**
  * Software Endstops
@@ -1263,6 +1358,9 @@
   #define MIN_SOFTWARE_ENDSTOP_X
   #define MIN_SOFTWARE_ENDSTOP_Y
   #define MIN_SOFTWARE_ENDSTOP_Z
+  #define MIN_SOFTWARE_ENDSTOP_I
+  #define MIN_SOFTWARE_ENDSTOP_J
+  #define MIN_SOFTWARE_ENDSTOP_K
 #endif
 
 // Max software endstops constrain movement within maximum coordinate bounds
@@ -1271,6 +1369,9 @@
   #define MAX_SOFTWARE_ENDSTOP_X
   #define MAX_SOFTWARE_ENDSTOP_Y
   #define MAX_SOFTWARE_ENDSTOP_Z
+  #define MAX_SOFTWARE_ENDSTOP_I
+  #define MAX_SOFTWARE_ENDSTOP_J
+  #define MAX_SOFTWARE_ENDSTOP_K
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
@@ -1582,6 +1683,9 @@
 //#define MANUAL_X_HOME_POS 0
 //#define MANUAL_Y_HOME_POS 0
 //#define MANUAL_Z_HOME_POS 0
+//#define MANUAL_I_HOME_POS 0
+//#define MANUAL_J_HOME_POS 0
+//#define MANUAL_K_HOME_POS 0
 
 // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
 //