Skip to content

Menu

Jump to bottom
egzumer edited this page Jan 24, 2024 · 60 revisions

Menu operation

The menu can be accessed with the M button (short press).

Once in the main menu, the menu items will be displayed on the left-hand side of the screen. The currently selected menu item will be highlighted and current value for that menu item will be shown on the right. Also, at the bottom left side a number of the menu item will be shown, ranging from 01 to the highest number.

To find the menu item to access, the UP/DOWN arrow keys may be used, or the menu item number (see lists below) may be entered on the numeric keypad. For instance, to access the VOX settings a number 57 can be entered on the keypad.

Once the desired menu item is highlighted, pressing the Menu key will enter into that menu item.

Once the menu item is selected, pressing the up and down arrow keys will adjust the setting for that menu item. To confirm the selection, press the Menu key. To cancel the selection, press the EXIT key.

Main menu

The number in front of the menu-item-description is a menu item number that can be used for quick selection

  1. Step - step of the frequency (in kHz), up/down buttons change frequency by this value, also you can only set a frequency that is multiple of half of this value.
  2. TxPwr - radio output power (LOW/MID/HIGH)
  3. RxDCS - receiver Digital-Coded Squelch, if you enable this, squelch will only unlock if this code is being received. You can start a DCS/CTCSS scan while you are in this menu option by pressing * SCAN button
  4. RxCTCS - receiver Continuous Tone-Coded Squelch System, squelch will only unlock if this code is being received. You can start a DCS/CTCSS scan while you are in this menu option by pressing * SCAN button
  5. TxDCS - transmitter Digital-Coded Squelch, radio will send given code while transmitting
  6. TxCTCS - transmitter Continuous Tone-Coded Squelch System, radio will send given code while transmitting
  7. TxODir - transmitter frequency offset direction
  8. TxOffs - transmitter frequency offset value
  9. W/N - bandwidth used by transceiver
    • WIDE - 25kHz
    • NARROW - 12.5kHz
  10. Scramb - scrambler, distorts the audio so it would be harder to understand for other listeners, if two radios use the same setting they can communicate
  11. BusyCL - busy channel lockout, blocks radio from transmitting when signal is being received
  12. Compnd - compander (compressor/expander), allows signals with a large dynamic range to be transmitted over facilities that have a smaller dynamic range capability, improves audio quality, both radios should use this option
  13. Demodu - demodulator mode, default is FM, AM/USB can be used for listening only
  14. ScAdd1 - add channel to scan list 1
  15. ScAdd2 - add channel to scan list 2
  16. ChSave - save current setting to a memory channel
  17. ChDele - delete memory channel
  18. ChName - modify memory channel name
    • Use up/down keys to select a channel to edit
    • Press the Menu button again to enter edit name mode
    • Use up/down keys or digits (0 ~ 9) to cycle the letters etc.
    • Press the Menu button to move to the next character position
    • Repeat above two steps till you reach the end
    • When "Sure?" pops up, press Menu to save, or Exit to cancel
    • Press Exit at any time to cancel the edit and return to main menu.
  19. SList - selects which channel is used by memory channel scanner
  20. SList1 - channels assigned to scan list 1
  21. SList2 - channels assigned to scan list 2
  22. ScnRev - scan resume mode
    • CARRIER - resume scan after signal disappears
    • TIMEOUT - resume scan after 5 seconds pause
    • STOP - after receiving a signal, stop the scan
  23. F1Shrt - side button 1 short press function
  24. F1Long - side button 1 long press function
  25. F2Shrt - side button 2 short press function
  26. F2Long - side button 2 long press function
  27. M Long - menu button long press function
  28. KeyLck - auto keypad lock option
  29. TxTOut - max transmission time limit
  30. BatSav - battery save option, a rate between active time and sleep time
  31. Mic - microphone sensitivity
  32. MicBar - microphone bar that appears while transmitting
  33. ChDisp - channel display style
  34. POnMsg - power on message
  35. BatTxt - additional battery value on the status bar in % or volts
  36. BackLt - backlight duration
  37. BLMin - minimal backlight brightness, when the screen backlight turns OFF it will go dim to this value
  38. BLMax - maximal backlight brightness, when the screen backlight turns ON it will turn bright to this value
  39. BltTRX - backlight activation on TX or RX
  40. Beep - keypad press beep sound
  41. Roger - roger beep at the end of transmission
  42. STE - squelch tail eliminator, eliminates noise at the end of a transmission
  43. RP STE - repeater squelch tail eliminator
  44. 1 Call - one key call channel, lets you quickly switch to the channel with 9 Call button
  45. ANI ID - DTMF communication radio ID
  46. UPCode - DTMF code that is sent at the beginning of transmission
  47. DWCode - DTMF code that is sent at the end of a transmission
  48. PTT ID - sets if UPCode and/or DWCode should be transmitted
  49. D ST - DTMF side tone switch, lets you hear transmitted tones in the radio speaker
  50. D Resp - DTMF decoding response
    • DO NOTHING: do nothing
    • RING - Local ringing
    • REPLY - reply response
    • BOTH - local ringing + reply response
  51. D Hold - DTMF auto reset time
  52. D Prel - DTMF pre-load time
  53. D Decd - enables DTMF decoder
  54. D List - list of DTMF contacts
  55. D Live - displays DTMF codes received by radio in the middle of the screen
  56. AM Fix - activates autogain AM fix function
  57. VOX - voice TX activation sensitivity level VOX Setting
  58. BatVol - battery voltage and percentage
  59. RxMode - sets how the upper and lower frequency is used
    • MAIN ONLY - always transmits and listens on the main frequency
    • DUAL RX RESPOND - listens to both frequencies, if signal is received on the secondary frequency it locks to it for a couple of seconds so you can respond to the call (DWR)
    • CROSS BAND - always transmits on the primary and listens on the secondary frequency (XB)
    • MAIN TX DUAL RX - always transmits on the primary, listens to both (DW)
  60. Sql - squelch sensitivity level

Hidden menu

Hidden menu is activated by holding PTT + SIDE BUTTON 1 while turning on the radio and than Release All Keys.

  1. F Lock - sets the TX frequency band plan.
    • DEFAULT+ (137-174, 400-470) - allows TX on default bands, plus options Tx 200, Tx 350, Tx 500
    • FCC HAM (144-148, 420-450)
    • CE HAM (144-146, 430-440)
    • GB HAM (144-148, 430-440)
    • (137-174, 400-430)
    • (137-174, 400-438)
    • DISABLE ALL - disables TX on all frequencies
    • UNLOCK ALL - enables TX on all bands (it has additional lock, read a wiki on how to turn that on)
  2. Tx 200 - enables TX on 200MHz
  3. Tx 350 - enables TX on 350MHz
  4. Tx 500 - enables TX on 500MHz
  5. 350 En - enables RX on 350MHz
  6. ScraEn - enables scrambler function
  7. BatCal - battery calibration, measure the voltage on the back of the radio, and adjust the value in the menu accordingly
  8. BatTyp - battery type, 1600mAh and 2200mAh battery has very different discharge curve, this is used to calculate battery level percentage
  9. Reset - resets radio configuration settings
    • VFO - removes only channel settings
    • ALL - resets all radio settings

=> Return to Home page

Clone this wiki locally