MM10 mixer dat added, fixes #270

[MichaelDvP]

• Added data for MM10
• added boiler exhaust temperature in UBAMonitorSlow
• renamed "desired temperature" to "desinfection temperature" in UBAParameterWW
  Checked working on BBQKees- Hardware.

devices
These device IDs are on the EMS Bus: 0x08 0x09 0x10 0x21
and 4 were recognized by EMS-ESP as:
MC10 Module (DeviceID:0x08 ProductID:72 Version:03.00)
BC10/RFM20 Receiver (DeviceID:0x09 ProductID:68 Version:02.03)
RC35 (DeviceID:0x10 ProductID:86 Version:01.18)
MM10 Mixer Module (DeviceID:0x21 ProductID:69 Version:02.01)

system
ESP8266 System stats:
[APP] EMS-ESP version: 1.9.5b5
[APP] MyESP version: 1.2.22
[APP] Build timestamp: 2019-12-30 13:52:32
[APP] Uptime: 0 days 0 hours 1 minute 32 seconds
[APP] System Load: 1%
[WIFI] WiFi Hostname: ems
[WIFI] WiFi IP: 192.168.0.118
[WIFI] WiFi signal strength: 88%
[WIFI] WiFi MAC: 98:F4:AB:CD:66:62
[MQTT] is connected (heartbeat disabled)
[NTP] Local Time is 13:58:10 CET (1577714290)
[SYSTEM] System is Stable
[SYSTEM] Board: PLATFORMIO_D1_MINI
[SYSTEM] CPU frequency: 80 MHz
[SYSTEM] SDK version: 2.2.2-dev(38a443e)
[SYSTEM] CPU chip ID: 0xCD6662
[SYSTEM] Core version: 2_6_2
[SYSTEM] Boot version: 31
[SYSTEM] Boot mode: 1
[SYSTEM] Last reset reason: Restart from terminal
[SYSTEM] Restart count: 0
[SYSTEM] # TCP disconnects: 0
[SYSTEM] rtcmem status: blocks:2 addr:0x60001280
[SYSTEM] rtcmem 00: 1163087990
[SYSTEM] rtcmem 01: 65536
[FLASH] Flash chip ID: 0x1640EF
[FLASH] Flash speed: 40000000 Hz
[FLASH] Flash mode: DIO
[FLASH] Flash size (CHIP): 4194304
[FLASH] Flash size (SDK): 4194304
[FLASH] Flash Reserved: 4096
[MEM] Firmware size: 615072
[MEM] Max OTA size: 2523136
[MEM] OTA Reserved: 16384
[MEM] Free Heap: 24104 bytes initially | 10920 bytes used (45%) | 13184 bytes free (54%)

info
EMS-ESP system stats:
System logging set to None
LED: off, Listen mode: off
2 external temperature sensors found
Boiler: enabled, Thermostat: enabled, Solar Module: disabled, Mixing Module: enabled
Shower Timer: disabled, Shower Alert: disabled

EMS Bus stats:
Bus is connected, protocol: Buderus
Rx: # successful read requests=201, # CRC errors=1
Tx: Last poll=1.931 seconds ago, # successful write requests=10

Boiler stats:
Boiler: MC10 Module (DeviceID:0x08 ProductID:72 Version:03.00)
Hot tap water: off
Central heating: active
Warm Water activated: on
Warm Water circulation pump available: on
Warm Water comfort setting: Hot
Warm Water selected temperature: 50 C
Warm Water desinfection temperature: 70 C
Warm Water current temperature: 49.7 C
Warm Water current tap water flow: 0.0 l/min
Warm Water # starts: 6221 times
Warm Water active time: 49 days 7 hours 41 minutes
Warm Water 3-way valve: off
Selected flow temperature: 75 C
Current flow temperature: 59.0 C
Return temperature: ? C
Gas: on
Boiler pump: off
Fan: on
Ignition: off
Circulation pump: off
Burner selected max power: 100 %
Burner current power: 100 %
Flame current: 52.4 uA
System pressure: ? bar
System service code: -H (0)
Heating temperature setting on the boiler: 90 C
Boiler circuit pump modulation max power: 100 %
Boiler circuit pump modulation min power: 100 %
Outside temperature: -0.4 C
Boiler temperature: 64.2 C
Exhaust temperature: 48.9 C
Pump modulation: 0 %
Burner # starts: 126759 times
Total burner operating time: 410 days 20 hours 49 minutes
Total heat operating time: 386 days 16 hours 4 minutes
Total UBA working time: 2595 days 20 hours 22 minutes

Thermostat stats:
Thermostat: RC35 (DeviceID:0x10 ProductID:86 Version:01.18)
Thermostat time is 14:09:10 30/12/2019
Heating Circuit 2
Current room temperature: ? C
Setpoint room temperature: 21.0 C
Day temperature: 21.0 C
Night temperature: 18.0 C
Vacation temperature: 17.0 C
Mode is set to auto
Day Mode is set to day

Mixing module stats:
Switch temperature: 3200.0 C
Mixing Circuit 1
Current flow temperature: 57.5 C
Setpoint flow temperature: 60 C
Current pump modulation: 100 %

External temperature sensors:
Sensor #1 DS18B20: 46.31 C
Sensor #2 DS18B20: 38.43 C

[proddy]

nice! I'll take a look and do the merge shortly.