-
-
Notifications
You must be signed in to change notification settings - Fork 638
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
em2go startet immer bei 11kW - PV Modus - Regelt nicht schnell genug - bricht ab #14307
Comments
Logs zu Problem 2
|
was mir zu problem 1 eigenartig erscheint: ich sehe nirgendwo etwas von "max charge current:" im log - weil da wird der errechnete strom (pv charge current) an die wallbox gesendet. deswegen haut die mit 11kW rein, sobald das enable kommt, weil der errechnete ueberschuss niemals uebermittel wurde. (und dann geht sie natuerlich wieder aus wegen netzbezug). |
Jetzt im Tagesbetrieb wo ein ständiger Sonnen/Wolken Wechsel ist und auch die Küche unter Volllast läuft, funktioniert das drosseln und Phasenumschalten
|
ja, jetzt sieht man ja auch, dass da immer "max charge current:" steht, also die box auch echt angesteuert wird. und dass passiert, wenn sich der zur verfuegung stehende ladestrom aendert und er groesser als effectiveMinCurrent ist:
eine der beiden bedingungen muss bei dir am morgen da im wege stehen. |
und es geht munter weiter - die Küche beendet den Betrieb und wir haben 5-16kW Überschuss zusätzlich zu den 3,7kW einphasigen laden. Keine Anzeichen auf dreiphasig umzuschalten über mehr als 10min. Erst ein manuelles "aus" und wieder auf "PV" ermöglicht den 3-phasigen Betrieb
|
Bevor wir ein Suchspiel machen- was ist der relevante Teil des Logs? |
Soweit ich sehe, soll hier 1p Laden starten:
Da die Box keine Phasenumschaltung hat: wie soll das funktionieren? Wo kommt das 1p her? |
Hat sie doch aber?:
|
Ja sie hat eine Phasenumschaltung und sie schaltet auch teilweise um. Aber eben im ersten Beispiel nicht nach unten, dort regelt sie die Last nicht mal auf 4,6kW bei 3p sondern stoppt einfach nur bevor der Spaß wieder von vorne los geht. |
Aso ja, die home. Mir sind das zuviele Logs durcheinander. Können wir mal auf ein relevantes schauen und auf den relevanten Ladepunkt? Wie sieht das aus? |
This is confusing:
I don't see how we can end up with 1p detected here: func (lp *Loadpoint) ActivePhases() int {
physical := lp.GetPhases()
vehicle := lp.getVehiclePhases()
measured := lp.getMeasuredPhases()
charger := lp.getChargerPhysicalPhases()
active := min(expect(vehicle), expect(physical), expect(measured), expect(charger))
return active
} Einer der Werte muss 1 sein, vmtl. sogar der measured Wert. Nur wie kann das sein? Wenn uns nix Besseres einfällt muss da nochmal ein Logging rein. /cc @GrimmiMeloni |
Logging ist morgen im nightly, dann bitte neu testen (nicht auf HA...) |
Aufforderung an mich ? Konnte es zumindest reproduzieren, das sind diesmal nur die Auszüge aus dem Log. Falls mehr benötigt wird, gern sagen wir
|
@kasn24 Das Log ist entweder unvollständig, oder zu kurz. Die entscheidende Information bzgl. der Phasenerkennung fehlt. Bitte mal ein Log teilen, das vor dem Ladestart bzw. Einstecken des Fahrzeugs beginnt, und auch den Ladevorgang mit den 11kW für ein paar Minuten aufzeichnet. |
Sorry, beim letzten Mal waren die Logs zu lang... Mir scheint es aus Sicht eines Laien, die Wallbox erhält nur den Befehl "start" und geht selbstständig mit der Leistung hoch ohne eine Maximalgrenze von evcc zu bearbeiten. |
so habe die Wallbox von Aus PV gestellt um 08:50 Uhr. Gefiltert auf LP-2
Ohne Filter, gesamter Log
|
sieht so aus, als wuerde evcc alles richtig machen: fragt 1p/6A
aber wallbox macht 3p/16A
vielleicht noch mal alles mit settings
|
Habe lp-2 zusätzlich auch mal auf Trace gesetzt - ebenfalls auf 0.127.1 geupdatet Eben hatten wir das Spiel, lp-2 steigt mit 11kW ein (obwohl weniger sinnvoll wäre). Daraufhin wird lp-1 gedrosselt und lp-2 bricht wieder ab.
|
bei den gobalen settings ganz oben - aber das ist vllt. nicht notwendig, |
90s ist aber heftig. Bei 2 Loadpoints wird der einzelne LP nur alle 3 Minuten geregelt. Das könnte bereits zu lang für den PV Timer sein (je nach Setting). Ggf. also eher mit 45s Interval probieren. |
Hmm.. könnte ein Netzwerkproblem die Ursache sein oder würde evcc dies bemerken? |
sollte es ein allgemeineres em2go problem sein (von wegen langsam oder ignorant?) |
Danke an alle Beteiligten und Mitlesenden! Bzgl. dem oben genannten Problem mit der SMA Wallbox und MG die nicht abschalten, eröffne ich am besten ein eigenes Thema oder kennt hier jemand was vergleichbares? habe noch nichts passendes gefunden .. ausversehen geschlossen - sorry neu hier |
@kasn24 kannst Du mal bitte probieren, ob Du- wenn die Umschaltung nicht geklappt hat- diese auf der Kommandozeile erzwingen kannst? Also mittels:
|
Habe das gleich problem. Der em2go home setzt beim Starten des Ladens immer den Max. Strom (16A) als Sollstrom ein. |
gemäß Anleitung installiert ist im prinzip gut. passiert dann weiter nichts mehr? |
muss natuerlich evcc charger em2goWilly sein. |
Achso mir war nicht bewusst, dass ich mit dem Befehl eine neue Instanz starte, ich dachte ich mische in die aktuell laufende Instanz ein mit dem Befehl den Charger im aktiven Ladevorgang zum Phasenwechsel zu bewegen. Nein bei beiden Befehlen ist nach wenigen Sekunden Schluss. Also nachdem MQTT Erfolg vermeldet. |
Jetzt muss ich mal stop sagen.
@kasn24 bitte nicht raten. Davon war nie die Rede! Das ist kein Service sondern einfach nur ein kleiner Befehl.
@RenatusRo bitte nicht raten. Das mag sein, gerade bei Modbus ist das aber oft gar kein Problem. Wir wollen ja gerade raus finden, ob die Umschaltung klappt während der Service das nicht kann. NICHT möglich ist das nur wenn die Box nur einen TCP/Modbus Client zulässt.
@kasn24 damit wir nicht raten: wie sieht /etc/evcc.yaml aus? Ist die korrekt?
Das geht tatsächlich nicht (falls die IP stimmt, können wir natürlich nicht verifizieren). Der einfache Test nutzt also nix. Anonymisieren der IPs kann du dir sparen, in Dein Netz kann ohnehin niemand rein schauen. An dieser Stelle: ich gebs auf. em2go scheint manchmal die Phasen nicht umzuschalten, trace log beweist das. Da hilft nur Ticket beim Hersteller. |
Raten musste ich, da ich noch kein Wiki diesbezüglich gefunden habe. Ja die etc/evcc.yaml passt, die ist wie ganz oben aus HA nur die IPs der Instanz und für MQTT angepasst. Und ja die IPs passen auch alle, ohne irgendwelche Befehle läuft das System ja. Nur der von dir genannte Befehl eben nicht. und auch hier musste ich dann halt raten nach "Du verwendest eine andere Konfigdatei- user vs service. Bitte beim Aufruf die richtige angeben!" Aber ist ja auch egal, da für dich erledigt. Danke trotzdem! |
Es gibt halt nix zu prüfen da das neben dem Service bei der Box nicht möglich ist. Also Ticket beim Hersteller :(. Mit dem Ergebnis gerne wieder melden. |
Ist schon in der mache. |
@andig |
Wir werden in #14480 noch einen Workaround nachliefern. Damit kann evcc dann hoffentlich reagieren. Danke für eure Geduld! |
@RenatusRo @kasn24 könnt ihr bitte morgen mal das Nightly ausprobieren? Damit sollten wir eigentlich in der Lage sein, sowohl zuviele Phasen als auch zu hohen Strom zu korrigieren! |
Ich bin morgen nicht zuhause, Montag reiche ich nach. |
Klappt nicht - bin im Nightly
|
|
Ok, was konkret klappt nicht? Soweit ich sehe wird jetzt auf 1p runter geregelt wie erwartet. Dass er auf 11kW startet können wir nicht verhindern da die Box anscheinend ein Eigenleben hat. |
Der Start ist gar nicht mehr das Problem. Das klappt echt ganz gut mit den Interval von 15 Sekunden. Hier geht er nicht mehr von 1p auf 3p hoch. evcc zählt runter, aber trotz 7-10kW Überschuss klappt es nicht.
|
Ja, das ist doof. Die Situation können wir leider nicht erkennen. Leider scheint die WB zu behaupten auf 3p zu laufen, tut das aber nicht. Da muss jetzt tatsächlich der Support ran :( |
Du kannst morgen gerne nochmal das |
Ich gehe dann davon aus, dass auch das "Phasenregister" write-only ist und beim lesen einfach nur den letzten dort hineingeschrieben Wert zurück gibt statt den tatsächlichen Zustand zu respräsentieren (vergleichbar mit dem "Stromregister"). |
verhaelt sich unauffaellig (mit der PRO): vorher keine probleme und jetzt auch nicht (derzeit nur im 1p-betrieb ausprobiert, da im alltag die anderen 2p per trennschalter abgeschaltet sind). |
Wenig vorher, wieder der gescheiterte Phasenwechsel auf 3p
|
Wie erwartet:
Ich habe em2go über unseren Kanal angeschrieben. |
Danke, ich habe die Logs von gestern auch nochmal nachgeschickt an den Support! Weiterer Test: Stellung auf Aus und dann wieder auf PV und er startet erfolgreich 3p
|
@andig Braucht die Box vielleicht vor der Umschaltung immer einen expliziten Stop bzw. übernimmt den im Register stehenden Phasenwert nur beim Starten? |
Bei meiner em2go Home Box funktioniert die automatische Phasenerkennung und Umschaltung auch nicht richtig (inconsistent phases etc...). Manuell funktioniert die Phasenumschaltung problemlos. Also während des Ladevorgangs manuell z.B. im Min+PV Modus in der evcc GUI von 1-phasig auf 3-phasig umschalten und wieder zurück. Ich muss den Ladevorgang dafür auch nicht stoppen. Wird bei der manuellen Umschaltung vielleicht ein anderer Funktionsaufruf verwendet, als wenn evcc automatisch die Phasen umschalten will? Die Erkennung der aktiven Phasen dauert auch eine Minute, nachdem die Phasen umgeschaltet wurden. Wenn aber die Erkennung dann funktioniert hat, wird wieder im 15 Sekunden Rhythmus die Phasenerkennung durchgeführt. Ich hab mal versucht im Log das zu highlighten.
|
An diesem Log sehe ich eigentlich nur zwei Dinge die mir allerdings eher Sorgen bereiten:
Letzteres darf so auf keinen Fall sein. Wenn man das mit dem falschen Fahrzeug macht gibt es ein großes Hallo. |
Da hab ich gar nicht darauf geachtet. Die Wallbox schaltet tatsächlich nicht (sichtbar) ab. Bin in die Garage und habs mir angeschaut (bzw. angehört). Man hört den Schütz klicken und weiter geht's mit dem Laden ohne (sichtbare) Unterbrechung. Im Display der Wallbox sieht man, dass der Strom bzw. die Ströme der einzelnen Phasen kurz auf 0 gehen und dann langsam nach der Umschaltung innerhalb von 2 Sekunden von 0 auf 6A steigen. Aber wer weiß, wie genau diese Anzeige ist. Wäre cool, wenn man den expliziten Stop-Befehl implementieren würde, weil scheinbar die Wallbox das selbst nicht machen will. |
Wenn die Box korrekt abschalten würde müsste es bei jeder Umschaltung mindestes zweimal "klicken". Mit mindestens 10s Pause dazwischen. |
Describe the bug
Hallo,
das Problem besteht komischerweise nur morgens bei "aufgehen" der Sonne. 70kWh Ladestand erreicht, 4kW Überschuss (bereits 1kW einphasig hätten gereicht, aber da war der Akku noch nicht voll genug)
Das Laden startet, die Wallbox zieht direkt auf 11kW hoch auch schneller als in evcc angezeigt wird. Das packt meistens auch mein Akku nicht und wir gehen in den Netzbezug.
Statt runter zu regeln oder sogar die Phasen zu wechseln, wird einfach abgebrochen.
Ich habe noch nichts derartiges gefunden, dass die Wallbox direkt mit 3 Phasen und der niedrigsten Amperezahl startet.
Die ebenfalls konfigurierte SMA Wallbox macht dies ohne Probleme.
Da kommen wir zu Problem 2, wo ich versuche zeitnah Logs nachzuliefern.
Die SMA Wallbox lädt den MG4 1-phasig bis voll, lädt dann konstant weiter mit ca. 10W und schaltet nicht ab. Dies führt zum "klacken" vom Ladegerät des MG4 und ist mit Sicherheit nicht gesund. Das hat die SMA Wallbox gesteuert über den HomeManager nicht gemacht.
Ich hoffe ihr könnt mir weiterhelfen.
Viele Grüße
Steps to reproduce
...
Configuration details
Log details
What type of operating system are you running?
HomeAssistant Add-on
Version
0.126.6
The text was updated successfully, but these errors were encountered: