[PATCH] SGI IP22 bits

An update for the Indy aka IP22 support.  Consolidates the 32-bit and
64-bit copies of the support code into one directory, so in total this
patch deletes quite a bit of code.

arch/mips/sgi-ip22/Makefile

@@ -0,0 +1,12 @@
+#
+# Makefile for the SGI specific kernel interface routines
+# under Linux.
+#
+
+obj-y	+= ip22-mc.o ip22-hpc.o ip22-int.o ip22-irq.o ip22-berr.o \
+	   ip22-time.o ip22-rtc.o ip22-nvram.o ip22-reset.o \
+	   ip22-setup.o ip22-ksyms.o
+
+obj-$(CONFIG_EISA)	+= ip22-eisa.o
+
+EXTRA_AFLAGS := $(CFLAGS)

arch/mips/sgi-ip22/ip22-berr.c

@@ -0,0 +1,91 @@
+/*
+ * ip22-berr.c: Bus error handling.
+ *
+ * Copyright (C) 2002 Ladislav Michl
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+
+#include <asm/addrspace.h>
+#include <asm/system.h>
+#include <asm/traps.h>
+#include <asm/branch.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/hpc3.h>
+
+
+static unsigned int cpu_err_stat;	/* Status reg for CPU */
+static unsigned int gio_err_stat;	/* Status reg for GIO */
+static unsigned int cpu_err_addr;	/* Error address reg for CPU */
+static unsigned int gio_err_addr;	/* Error address reg for GIO */
+
+static void save_and_clear_buserr(void)
+{
+	/* save memory controler's error status registers */
+	cpu_err_addr = sgimc->cerr;
+	cpu_err_stat = sgimc->cstat;
+	gio_err_addr = sgimc->gerr;
+	gio_err_stat = sgimc->gstat;
+
+	sgimc->cstat = sgimc->gstat = 0;
+}
+
+#define GIO_ERRMASK	0xff00
+#define CPU_ERRMASK	0x3f00
+
+static void print_buserr(void)
+{
+	if (cpu_err_stat & CPU_ERRMASK)
+		printk(KERN_ALERT "CPU error 0x%x<%s%s%s%s%s%s> @ 0x%08x\n",
+			cpu_err_stat,
+			cpu_err_stat & SGIMC_CSTAT_RD ? "RD " : "",
+			cpu_err_stat & SGIMC_CSTAT_PAR ? "PAR " : "",
+			cpu_err_stat & SGIMC_CSTAT_ADDR ? "ADDR " : "",
+			cpu_err_stat & SGIMC_CSTAT_SYSAD_PAR ? "SYSAD " : "",
+			cpu_err_stat & SGIMC_CSTAT_SYSCMD_PAR ? "SYSCMD " : "",
+			cpu_err_stat & SGIMC_CSTAT_BAD_DATA ? "BAD_DATA " : "",
+			cpu_err_addr);
+	if (gio_err_stat & GIO_ERRMASK)
+		printk(KERN_ALERT "GIO error 0x%x:<%s%s%s%s%s%s%s%s> @ 0x08%x\n",
+			gio_err_stat,
+			gio_err_stat & SGIMC_GSTAT_RD ? "RD " : "",
+			gio_err_stat & SGIMC_GSTAT_WR ? "WR " : "",
+			gio_err_stat & SGIMC_GSTAT_TIME ? "TIME " : "",
+			gio_err_stat & SGIMC_GSTAT_PROM ? "PROM " : "",
+			gio_err_stat & SGIMC_GSTAT_ADDR ? "ADDR " : "",
+			gio_err_stat & SGIMC_GSTAT_BC ? "BC " : "",
+			gio_err_stat & SGIMC_GSTAT_PIO_RD ? "PIO_RD " : "",
+			gio_err_stat & SGIMC_GSTAT_PIO_WR ? "PIO_WR " : "",
+			gio_err_addr);
+}
+
+/*
+ * MC sends an interrupt whenever bus or parity errors occur. In addition,
+ * if the error happened during a CPU read, it also asserts the bus error
+ * pin on the R4K. Code in bus error handler save the MC bus error registers
+ * and then clear the interrupt when this happens.
+ */
+
+void ip22_be_interrupt(int irq, struct pt_regs *regs)
+{
+	save_and_clear_buserr();
+	print_buserr();
+	panic("Bus error, epc == %08lx, ra == %08lx",
+	      regs->cp0_epc, regs->regs[31]);
+}
+
+int ip22_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	save_and_clear_buserr();
+	if (is_fixup)
+		return MIPS_BE_FIXUP;
+	print_buserr();
+	return MIPS_BE_FATAL;
+}
+
+void __init ip22_be_init(void)
+{
+	board_be_handler = ip22_be_handler;
+}