Next Generation of the ESP32-PWM-Driver-Devkit - Work in progress! RevC had a couple minor issues...

ESP32 Development kit with 8 PWM outputs that can be driven at 5-28V at up to 2A each

The primary purpose of the design is to control LED lighting (like these: https://www.amazon.ca/gp/product/B00QN4X5MM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 I am not affiliated with this seller, but the LED strips are great!), however there may be many other uses, like controlling DC motors! The board can be powered by either USB or by connecting 5-24V to the power input connector (connecting both is fine!), however do note that to use the PWM outputs an external power source is strongly recommended, as otherwise it will try to use the power from the USB bus and likely would cause power/stability issues.

Connecting via USB

Linux

If the device is not detected, you may need to add CONFIG_USB_SERIAL_CP210X=m to your kernel config:

Device Drivers --->
	USB Support --->
		USB Serial Converter Support --->
			<M>   USB CP210x family of UART Bridge Controllers  

If it's detected, you should see the following in /var/log/messages (may be syslog or other file depending on your distro):

Dec 31 17:57:51 nautilus kernel: usb 1-2.4: new full-speed USB device number 35 using ehci-pci
Dec 31 17:57:51 nautilus kernel: usb 1-2.4: New USB device found, idVendor=10c4, idProduct=ea60, bcdDevice= 1.00
Dec 31 17:57:51 nautilus kernel: usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Dec 31 17:57:51 nautilus kernel: usb 1-2.4: Product: CP2102N USB to UART Bridge Controller
Dec 31 17:57:51 nautilus kernel: usb 1-2.4: Manufacturer: VintLabs
Dec 31 17:57:51 nautilus kernel: usb 1-2.4: SerialNumber: 0002
Dec 31 17:57:51 nautilus kernel: cp210x 1-2.4:1.0: cp210x converter detected
Dec 31 17:57:51 nautilus kernel: usb 1-2.4: cp210x converter now attached to ttyUSB0

Windows

See https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers

Usage in Arduino environment

To use with Arduino, ensure that you have ESP32 boards added (if you have not, see https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-windows-instructions/ for some good instructions), and then select VintLabs ESP32 DevKit in Tools->Board. (If you do not see it in the list, please make sure that the ESP32 core is updated)

Example code: git clone https://github.com/vintlabs/VintLabs-PWM-Arduino-Basic-Example.git

// PWM Example for VintLabs ESP32 PWM Driver DevKit
// Connect an LED light from PWM0 on the board to ground (if using a discrete LED use a current limiting series resistor!)

// Select the PWM output to use - you can use PWM0-PWM7 for the VintLabs boards, or simply specify the GPIO number
const int pwmOutput = PWM0;

// Set the PWM frequency
const int frequency = 10000;

// Set the LED channel. Note that this is not related to a pin number, but an arbitrary channel number from 0-7
const int ledChannel = 0;

// Set the resolution. This can be 8, 10, 12 or 15 bits
const int resolution = 12;


void setup() {
  // Basic PWM setup
  ledcSetup(ledChannel, frequency, resolution);

  // Attach the actual output to the channel
  ledcAttachPin(pwmOutput, ledChannel);

}

void loop() {
  // Just loop from off to max, then back again
  for (int dc = 0; dc < pow(2, resolution); dc++)
  {
    // set the duty cycle
    ledcWrite(ledChannel, dc);
    delay(10);
  }
  for (int dc = pow(2, resolution) - 1; dc >= 0; dc--)
  {
    // set the duty cycle
    ledcWrite(ledChannel, dc);
    delay(10);
  }
}