Refactor Galatea

keyboards/studiokestra/galatea/config.h

@@ -1,47 +1,9 @@
-/*
-Copyright 2021 Studio Kestra
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
+// Copyright 2023 studiokestra (@studiokestra)
+// SPDX-License-Identifier: GPL-2.0-or-later
 
 #pragma once
 
-
-#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, C7, B2, D5 }
-#define MATRIX_ROW_PINS { D1, D0, B0, B7, E6, B3, B6, C6, D6, D7, B4, D3 }
-#define DIODE_DIRECTION COL2ROW
-
-#if defined(KEYBOARD_studiokestra_galatea_rev2)
-  #define RGB_DI_PIN D4
-  #define RGBLED_NUM 24
-  #define RGBLIGHT_HUE_STEP 8
-  #define RGBLIGHT_SAT_STEP 8
-  #define RGBLIGHT_VAL_STEP 8
-  #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
-  #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
-   #define RGBLIGHT_EFFECT_BREATHING
-   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
-   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
-   #define RGBLIGHT_EFFECT_SNAKE
-   #define RGBLIGHT_EFFECT_KNIGHT
-   #define RGBLIGHT_EFFECT_CHRISTMAS
-   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
-   #define RGBLIGHT_EFFECT_RGB_TEST
-   #define RGBLIGHT_EFFECT_ALTERNATING
-#endif
-
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
+#define LOCKING_RESYNC_ENABLE

keyboards/studiokestra/galatea/readme.md

@@ -1,27 +1,29 @@
-# Galatea
+# studiokestra/galatea
+
+![studiokestra/galatea](https://i.imgur.com/juPhV1xh.png)
 
 TKL H87/88c compatible PCB with support for the most common layouts.
 
 * Keyboard Maintainer: [Studio Kestra](https://github.com/studiokestra/)
-* Hardware Supported: [studiokestra.ca/galatea](https://studiokestra.ca/galatea/)
-* Hardware Availability: In-Stock Sale (Dec 2021)
+* Hardware Supported: Most H87C compatible keyboards
+* Hardware Availability: https://RNDKBD.com; https://geon.works/
 * Rev1 firmware is used for Galatea PCBs with no RGB underglow.
-* Rev2 firmware is used for Galatea PCBs with RGB underglow. 
+* Rev2 firmware is used for Galatea PCBs with RGB underglow.
 
-## Bootload Sequence
+Make example for this keyboard (after setting up your build environment):
 
-There are 3 ways to put the board in bootloader mode:
+    make studiokestra/galatea/rev1:default
 
-- Hold the top-left key (typically `Esc`) while plugging in the USB cable, OR
-- While the PCB is plugged into the PC, press the physical `RESET` button on the back of the board, OR
-- With the default layout, toggle Layer 1 and press the `R` key. 
+Flashing example for this keyboard:
 
-## Compiling Firmware
+    make studiokestra/galatea/rev1:default:flash
 
-Make example for this keyboard (after setting up your build environment):
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
 
-    make studiokestra/galatea/rev1:default
+## Bootloader
 
-If no revision is specified, it will build rev1 firmware by default.
+Enter the bootloader in 3 ways:
 
-See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
+* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
+* **Physical reset button**: Briefly press the button on the back of the PCB - some may have pads you must short instead
+* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available