Rename DRIVER_ADDR_n defines

docs/feature_led_matrix.md

@@ -23,10 +23,10 @@ You can use between 1 and 4 IS31FL3731 IC's. Do not specify `LED_DRIVER_ADDR_<N>
 | `IS31FL3731_I2C_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
 | `IS31FL3731_DRIVER_COUNT` | (Required) How many LED driver IC's are present | |
 | `LED_MATRIX_LED_COUNT` | (Required) How many LED lights are present across all drivers | |
-| `LED_DRIVER_ADDR_1` | (Required) Address for the first LED driver | |
-| `LED_DRIVER_ADDR_2` | (Optional) Address for the second LED driver | |
-| `LED_DRIVER_ADDR_3` | (Optional) Address for the third LED driver | |
-| `LED_DRIVER_ADDR_4` | (Optional) Address for the fourth LED driver | |
+| `IS31FL3731_I2C_ADDRESS_1` | (Required) Address for the first LED driver | |
+| `IS31FL3731_I2C_ADDRESS_2` | (Optional) Address for the second LED driver | |
+| `IS31FL3731_I2C_ADDRESS_3` | (Optional) Address for the third LED driver | |
+| `IS31FL3731_I2C_ADDRESS_4` | (Optional) Address for the fourth LED driver | |
 
 Here is an example using 2 drivers.
 
@@ -40,8 +40,8 @@ Here is an example using 2 drivers.
 // 11 AD <-> VCC
 // ADDR represents A1:A0 of the 7-bit address.
 // The result is: 0b11101(ADDR)
-#define LED_DRIVER_ADDR_1 IS31FL3731_I2C_ADDRESS_GND
-#define LED_DRIVER_ADDR_2 IS31FL3731_I2C_ADDRESS_SDA
+#define IS31FL3731_I2C_ADDRESS_1 IS31FL3731_I2C_ADDRESS_GND
+#define IS31FL3731_I2C_ADDRESS_2 IS31FL3731_I2C_ADDRESS_SDA
 
 #define IS31FL3731_DRIVER_COUNT 2
 #define LED_DRIVER_1_LED_TOTAL 25
@@ -51,7 +51,7 @@ Here is an example using 2 drivers.
 
 !> Note the parentheses, this is so when `LED_MATRIX_LED_COUNT` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (LED_DRIVER_1_LED_TOTAL + LED_DRIVER_2_LED_TOTAL)` will give very different results than `rand() % LED_DRIVER_1_LED_TOTAL + LED_DRIVER_2_LED_TOTAL`.
 
-For split keyboards using `LED_MATRIX_SPLIT` with an LED driver, you can either have the same driver address or different driver addresses. If using different addresses, use `DRIVER_ADDR_1` for one and `DRIVER_ADDR_2` for the other one. Then, in `g_is31fl3731_leds`, fill out the correct driver index (0 or 1). If using one address, use `DRIVER_ADDR_1` for both, and use index 0 for `g_is31fl3731_leds`.
+For split keyboards using `LED_MATRIX_SPLIT` with an LED driver, you can either have the same driver address or different driver addresses. If using different addresses, use `IS31FL3731_I2C_ADDRESS_1` for one and `IS31FL3731_I2C_ADDRESS_2` for the other one. Then, in `g_is31fl3731_leds`, fill out the correct driver index (0 or 1). If using one address, use `IS31FL3731_I2C_ADDRESS_1` for both, and use index 0 for `g_is31fl3731_leds`.
 
 Define these arrays listing all the LEDs in your `<keyboard>.c`:
 

docs/feature_rgb_matrix.md

@@ -24,10 +24,10 @@ You can use between 1 and 4 IS31FL3731 IC's. Do not specify `DRIVER_ADDR_<N>` de
 | `IS31FL3731_DEGHOST` | (Optional) Set this define to enable de-ghosting by halving Vcc during blanking time | |
 | `IS31FL3731_DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
 | `RGB_MATRIX_LED_COUNT` | (Required) How many RGB lights are present across all drivers | |
-| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
-| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
-| `DRIVER_ADDR_3` | (Optional) Address for the third RGB driver | |
-| `DRIVER_ADDR_4` | (Optional) Address for the fourth RGB driver | |
+| `IS31FL3731_I2C_ADDRESS_1` | (Required) Address for the first RGB driver | |
+| `IS31FL3731_I2C_ADDRESS_2` | (Optional) Address for the second RGB driver | |
+| `IS31FL3731_I2C_ADDRESS_3` | (Optional) Address for the third RGB driver | |
+| `IS31FL3731_I2C_ADDRESS_4` | (Optional) Address for the fourth RGB driver | |
 
 Here is an example using 2 drivers.
 
@@ -41,8 +41,8 @@ Here is an example using 2 drivers.
 // 11 AD <-> VCC
 // ADDR represents A1:A0 of the 7-bit address.
 // The result is: 0b11101(ADDR)
-#define DRIVER_ADDR_1 IS31FL3731_I2C_ADDRESS_GND
-#define DRIVER_ADDR_2 IS31FL3731_I2C_ADDRESS_SDA
+#define IS31FL3731_I2C_ADDRESS_1 IS31FL3731_I2C_ADDRESS_GND
+#define IS31FL3731_I2C_ADDRESS_2 IS31FL3731_I2C_ADDRESS_SDA
 
 #define IS31FL3731_DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 25
@@ -52,7 +52,7 @@ Here is an example using 2 drivers.
 
 !> Note the parentheses, this is so when `RGB_MATRIX_LED_COUNT` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
 
-For split keyboards using `RGB_MATRIX_SPLIT` with an LED driver, you can either have the same driver address or different driver addresses. If using different addresses, use `DRIVER_ADDR_1` for one and `DRIVER_ADDR_2` for the other one. Then, in `g_is31fl3731_leds`, fill out the correct driver index (0 or 1). If using one address, use `DRIVER_ADDR_1` for both, and use index 0 for `g_is31fl3731_leds`.
+For split keyboards using `RGB_MATRIX_SPLIT` with an LED driver, you can either have the same driver address or different driver addresses. If using different addresses, use `IS31FL3731_I2C_ADDRESS_1` for one and `IS31FL3731_I2C_ADDRESS_2` for the other one. Then, in `g_is31fl3731_leds`, fill out the correct driver index (0 or 1). If using one address, use `IS31FL3731_I2C_ADDRESS_1` for both, and use index 0 for `g_is31fl3731_leds`.
 
 Define these arrays listing all the LEDs in your `<keyboard>.c`:
 
@@ -93,14 +93,14 @@ You can use between 1 and 4 IS31FL3733 IC's. Do not specify `DRIVER_ADDR_<N>` de
 | `IS31FL3733_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
 | `IS31FL3733_DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
 | `RGB_MATRIX_LED_COUNT` | (Required) How many RGB lights are present across all drivers | |
-| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
-| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
-| `DRIVER_ADDR_3` | (Optional) Address for the third RGB driver | |
-| `DRIVER_ADDR_4` | (Optional) Address for the fourth RGB driver | |
-| `DRIVER_SYNC_1` | (Optional) Sync configuration for the first RGB driver | 0 |
-| `DRIVER_SYNC_2` | (Optional) Sync configuration for the second RGB driver | 0 |
-| `DRIVER_SYNC_3` | (Optional) Sync configuration for the third RGB driver | 0 |
-| `DRIVER_SYNC_4` | (Optional) Sync configuration for the fourth RGB driver | 0 |
+| `IS31FL3733_I2C_ADDRESS_1` | (Required) Address for the first RGB driver | |
+| `IS31FL3733_I2C_ADDRESS_2` | (Optional) Address for the second RGB driver | |
+| `IS31FL3733_I2C_ADDRESS_3` | (Optional) Address for the third RGB driver | |
+| `IS31FL3733_I2C_ADDRESS_4` | (Optional) Address for the fourth RGB driver | |
+| `IS31FL3733_SYNC_1` | (Optional) Sync configuration for the first RGB driver | 0 |
+| `IS31FL3733_SYNC_2` | (Optional) Sync configuration for the second RGB driver | 0 |
+| `IS31FL3733_SYNC_3` | (Optional) Sync configuration for the third RGB driver | 0 |
+| `IS31FL3733_SYNC_4` | (Optional) Sync configuration for the fourth RGB driver | 0 |
 
 The IS31FL3733 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`IS31FL3733_SWPULLUP`/`IS31FL3733_CSPULLUP` are given the value of `IS31FL3733_PUR_0R`), the values that can be set to enable de-ghosting are as follows:
 
@@ -127,8 +127,8 @@ Here is an example using 2 drivers.
 // ADDR1 represents A1:A0 of the 7-bit address.
 // ADDR2 represents A3:A2 of the 7-bit address.
 // The result is: 0b101(ADDR2)(ADDR1)
-#define DRIVER_ADDR_1 IS31FL3733_I2C_ADDRESS_GND_GND
-#define DRIVER_ADDR_2 IS31FL3733_I2C_ADDRESS_GND_VCC
+#define IS31FL3733_I2C_ADDRESS_1 IS31FL3733_I2C_ADDRESS_GND_GND
+#define IS31FL3733_I2C_ADDRESS_2 IS31FL3733_I2C_ADDRESS_GND_VCC
 
 #define IS31FL3733_DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 58
@@ -180,10 +180,10 @@ Configure the hardware via your `config.h`:
 | `IS31FL3736_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
 | `IS31FL3736_DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
 | `RGB_MATRIX_LED_COUNT` | (Required) How many RGB lights are present across all drivers | |
-| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
-| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
-| `DRIVER_ADDR_3` | (Optional) Address for the third RGB driver | |
-| `DRIVER_ADDR_4` | (Optional) Address for the fourth RGB driver | |
+| `IS31FL3736_I2C_ADDRESS_1` | (Required) Address for the first RGB driver | |
+| `IS31FL3736_I2C_ADDRESS_2` | (Optional) Address for the second RGB driver | |
+| `IS31FL3736_I2C_ADDRESS_3` | (Optional) Address for the third RGB driver | |
+| `IS31FL3736_I2C_ADDRESS_4` | (Optional) Address for the fourth RGB driver | |
 
 The IS31FL3736 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`IS31FL3736_SWPULLUP`/`IS31FL3736_CSPULLUP` are given the value of `IS31FL3736_PUR_0R`), the values that can be set to enable de-ghosting are as follows:
 
@@ -211,8 +211,8 @@ Here is an example using 2 drivers.
 // ADDR1 represents A1:A0 of the 7-bit address.
 // ADDR2 represents A3:A2 of the 7-bit address.
 // The result is: 0b101(ADDR2)(ADDR1)
-#define DRIVER_ADDR_1 IS31FL3736_I2C_ADDRESS_GND_GND
-#define DRIVER_ADDR_2 IS31FL3736_I2C_ADDRESS_GND_SCL
+#define IS31FL3736_I2C_ADDRESS_1 IS31FL3736_I2C_ADDRESS_GND_GND
+#define IS31FL3736_I2C_ADDRESS_2 IS31FL3736_I2C_ADDRESS_GND_SCL
 
 #define IS31FL3736_DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 30
@@ -257,10 +257,10 @@ Configure the hardware via your `config.h`:
 | `IS31FL3737_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
 | `IS31FL3737_DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
 | `RGB_MATRIX_LED_COUNT` | (Required) How many RGB lights are present across all drivers | |
-| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
-| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
-| `DRIVER_ADDR_3` | (Optional) Address for the third RGB driver | |
-| `DRIVER_ADDR_4` | (Optional) Address for the fourth RGB driver | |
+| `IS31FL3737_I2C_ADDRESS_1` | (Required) Address for the first RGB driver | |
+| `IS31FL3737_I2C_ADDRESS_2` | (Optional) Address for the second RGB driver | |
+| `IS31FL3737_I2C_ADDRESS_3` | (Optional) Address for the third RGB driver | |
+| `IS31FL3737_I2C_ADDRESS_4` | (Optional) Address for the fourth RGB driver | |
 
 The IS31FL3737 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`IS31FL3737_SWPULLUP`/`IS31FL3737_CSPULLUP` are given the value of `IS31FL3737_PUR_0R`), the values that can be set to enable de-ghosting are as follows:
 
@@ -287,8 +287,8 @@ Here is an example using 2 drivers.
 // 1111 ADDR <-> VCC
 // ADDR represents A3:A0 of the 7-bit address.
 // The result is: 0b101(ADDR)
-#define DRIVER_ADDR_1 IS31FL3737_I2C_ADDRESS_GND
-#define DRIVER_ADDR_2 IS31FL3737_I2C_ADDRESS_SCL
+#define IS31FL3737_I2C_ADDRESS_1 IS31FL3737_I2C_ADDRESS_GND
+#define IS31FL3737_I2C_ADDRESS_2 IS31FL3737_I2C_ADDRESS_SCL
 
 #define IS31FL3737_DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 30
@@ -480,10 +480,10 @@ You can use up to 2 AW20216S IC's. Do not specify `DRIVER_<N>_xxx` defines for I
 
 | Variable | Description | Default |
 |----------|-------------|---------|
-| `AW20216S_DRIVER_1_CS` | (Required) MCU pin connected to first RGB driver chip select line  | B13 |
-| `AW20216S_DRIVER_2_CS` | (Optional) MCU pin connected to second RGB driver chip select line  | |
-| `AW20216S_DRIVER_1_EN` | (Required) MCU pin connected to first RGB driver hardware enable line  | C13 |
-| `AW20216S_DRIVER_2_EN` | (Optional) MCU pin connected to second RGB driver hardware enable line  | |
+| `AW20216S_CS_PIN_1` | (Required) MCU pin connected to first RGB driver chip select line  | B13 |
+| `AW20216S_CS_PIN_2` | (Optional) MCU pin connected to second RGB driver chip select line  | |
+| `AW20216S_EN_PIN_1` | (Required) MCU pin connected to first RGB driver hardware enable line  | C13 |
+| `AW20216S_EN_PIN_2` | (Optional) MCU pin connected to second RGB driver hardware enable line  | |
 | `DRIVER_1_LED_TOTAL` | (Required) How many RGB lights are connected to first RGB driver  | |
 | `DRIVER_2_LED_TOTAL` | (Optional) How many RGB lights are connected to second RGB driver  | |
 | `AW20216S_DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
@@ -496,11 +496,11 @@ You can use up to 2 AW20216S IC's. Do not specify `DRIVER_<N>_xxx` defines for I
 Here is an example using 2 drivers.
 
 ```c
-#define AW20216S_DRIVER_1_CS B13
-#define AW20216S_DRIVER_2_CS B14
+#define AW20216S_CS_PIN_1 B13
+#define AW20216S_CS_PIN_2 B14
 // Hardware enable lines may be connected to the same pin
-#define AW20216S_DRIVER_1_EN C13
-#define AW20216S_DRIVER_2_EN C13
+#define AW20216S_EN_PIN_1 C13
+#define AW20216S_EN_PIN_2 C13
 
 #define AW20216S_DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 66

drivers/led/aw20216s.h

@@ -38,16 +38,16 @@
 #    define AW20216S_SPI_DIVISOR AW_SPI_DIVISOR
 #endif
 #ifdef DRIVER_1_CS
-#    define AW20216S_DRIVER_1_CS DRIVER_1_CS
+#    define AW20216S_CS_PIN_1 DRIVER_1_CS
 #endif
 #ifdef DRIVER_2_CS
-#    define AW20216S_DRIVER_2_CS DRIVER_2_CS
+#    define AW20216S_CS_PIN_2 DRIVER_2_CS
 #endif
 #ifdef DRIVER_1_EN
-#    define AW20216S_DRIVER_1_EN DRIVER_1_EN
+#    define AW20216S_EN_PIN_1 DRIVER_1_EN
 #endif
 #ifdef DRIVER_2_EN
-#    define AW20216S_DRIVER_2_EN DRIVER_2_EN
+#    define AW20216S_EN_PIN_2 DRIVER_2_EN
 #endif
 
 #define aw_led aw20216s_led_t

drivers/led/issi/is31fl3731-simple.h

@@ -23,6 +23,18 @@
 #include "progmem.h"
 
 // ======== DEPRECATED DEFINES - DO NOT USE ========
+#ifdef LED_DRIVER_ADDR_1
+#    define IS31FL3731_I2C_ADDRESS_1 LED_DRIVER_ADDR_1
+#endif
+#ifdef LED_DRIVER_ADDR_2
+#    define IS31FL3731_I2C_ADDRESS_2 LED_DRIVER_ADDR_2
+#endif
+#ifdef LED_DRIVER_ADDR_3
+#    define IS31FL3731_I2C_ADDRESS_3 LED_DRIVER_ADDR_3
+#endif
+#ifdef LED_DRIVER_ADDR_4
+#    define IS31FL3731_I2C_ADDRESS_4 LED_DRIVER_ADDR_4
+#endif
 #ifdef LED_DRIVER_COUNT
 #    define IS31FL3731_DRIVER_COUNT LED_DRIVER_COUNT
 #endif

drivers/led/issi/is31fl3731.h

@@ -22,6 +22,18 @@
 #include "progmem.h"
 
 // ======== DEPRECATED DEFINES - DO NOT USE ========
+#ifdef DRIVER_ADDR_1
+#    define IS31FL3731_I2C_ADDRESS_1 DRIVER_ADDR_1
+#endif
+#ifdef DRIVER_ADDR_2
+#    define IS31FL3731_I2C_ADDRESS_2 DRIVER_ADDR_2
+#endif
+#ifdef DRIVER_ADDR_3
+#    define IS31FL3731_I2C_ADDRESS_3 DRIVER_ADDR_3
+#endif
+#ifdef DRIVER_ADDR_4
+#    define IS31FL3731_I2C_ADDRESS_4 DRIVER_ADDR_4
+#endif
 #ifdef DRIVER_COUNT
 #    define IS31FL3731_DRIVER_COUNT DRIVER_COUNT
 #endif

drivers/led/issi/is31fl3733.h

@@ -24,6 +24,30 @@
 #include "progmem.h"
 
 // ======== DEPRECATED DEFINES - DO NOT USE ========
+#ifdef DRIVER_ADDR_1
+#    define IS31FL3733_I2C_ADDRESS_1 DRIVER_ADDR_1
+#endif
+#ifdef DRIVER_ADDR_2
+#    define IS31FL3733_I2C_ADDRESS_2 DRIVER_ADDR_2
+#endif
+#ifdef DRIVER_ADDR_3
+#    define IS31FL3733_I2C_ADDRESS_3 DRIVER_ADDR_3
+#endif
+#ifdef DRIVER_ADDR_4
+#    define IS31FL3733_I2C_ADDRESS_4 DRIVER_ADDR_4
+#endif
+#ifdef DRIVER_SYNC_1
+#    define IS31FL3733_SYNC_1 DRIVER_SYNC_1
+#endif
+#ifdef DRIVER_ADDR_2
+#    define IS31FL3733_SYNC_2 DRIVER_SYNC_2
+#endif
+#ifdef DRIVER_ADDR_3
+#    define IS31FL3733_SYNC_3 DRIVER_SYNC_3
+#endif
+#ifdef DRIVER_ADDR_4
+#    define IS31FL3733_SYNC_4 DRIVER_SYNC_4
+#endif
 #ifdef DRIVER_COUNT
 #    define IS31FL3733_DRIVER_COUNT DRIVER_COUNT
 #endif

drivers/led/issi/is31fl3736.h

@@ -22,6 +22,18 @@
 #include "progmem.h"
 
 // ======== DEPRECATED DEFINES - DO NOT USE ========
+#ifdef DRIVER_ADDR_1
+#    define IS31FL3736_I2C_ADDRESS_1 DRIVER_ADDR_1
+#endif
+#ifdef DRIVER_ADDR_2
+#    define IS31FL3736_I2C_ADDRESS_2 DRIVER_ADDR_2
+#endif
+#ifdef DRIVER_ADDR_3
+#    define IS31FL3736_I2C_ADDRESS_3 DRIVER_ADDR_3
+#endif
+#ifdef DRIVER_ADDR_4
+#    define IS31FL3736_I2C_ADDRESS_4 DRIVER_ADDR_4
+#endif
 #ifdef DRIVER_COUNT
 #    define IS31FL3736_DRIVER_COUNT DRIVER_COUNT
 #endif

drivers/led/issi/is31fl3737.h

@@ -24,6 +24,18 @@
 #include "progmem.h"
 
 // ======== DEPRECATED DEFINES - DO NOT USE ========
+#ifdef DRIVER_ADDR_1
+#    define IS31FL3737_I2C_ADDRESS_1 DRIVER_ADDR_1
+#endif
+#ifdef DRIVER_ADDR_2
+#    define IS31FL3737_I2C_ADDRESS_2 DRIVER_ADDR_2
+#endif
+#ifdef DRIVER_ADDR_3
+#    define IS31FL3737_I2C_ADDRESS_3 DRIVER_ADDR_3
+#endif
+#ifdef DRIVER_ADDR_4
+#    define IS31FL3737_I2C_ADDRESS_4 DRIVER_ADDR_4
+#endif
 #ifdef DRIVER_COUNT
 #    define IS31FL3737_DRIVER_COUNT DRIVER_COUNT
 #endif

drivers/led/issi/is31fl3741.h

@@ -24,6 +24,18 @@
 #include "progmem.h"
 
 // ======== DEPRECATED DEFINES - DO NOT USE ========
+#ifdef DRIVER_ADDR_1
+#    define IS31FL3741_I2C_ADDRESS_1 DRIVER_ADDR_1
+#endif
+#ifdef DRIVER_ADDR_2
+#    define IS31FL3741_I2C_ADDRESS_2 DRIVER_ADDR_2
+#endif
+#ifdef DRIVER_ADDR_3
+#    define IS31FL3741_I2C_ADDRESS_3 DRIVER_ADDR_3
+#endif
+#ifdef DRIVER_ADDR_4
+#    define IS31FL3741_I2C_ADDRESS_4 DRIVER_ADDR_4
+#endif
 #ifdef DRIVER_COUNT
 #    define IS31FL3741_DRIVER_COUNT DRIVER_COUNT
 #endif

keyboards/4pplet/perk60_iso/rev_a/config.h

@@ -21,7 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-#define DRIVER_ADDR_1 IS31FL3733_I2C_ADDRESS_GND_GND
+#define IS31FL3733_I2C_ADDRESS_1 IS31FL3733_I2C_ADDRESS_GND_GND
 #define IS31FL3733_DRIVER_COUNT 1
 #define RGB_MATRIX_LED_COUNT 62
 #define IS31FL3733_PWM_FREQUENCY IS31FL3733_PWM_FREQUENCY_26K7_HZ

keyboards/abko/ak84bt/config.h

@@ -17,8 +17,8 @@
 #pragma once
 
 
-#define DRIVER_ADDR_1 IS31FL3733_I2C_ADDRESS_GND_GND
-#define DRIVER_ADDR_2 IS31FL3733_I2C_ADDRESS_GND_VCC
+#define IS31FL3733_I2C_ADDRESS_1 IS31FL3733_I2C_ADDRESS_GND_GND
+#define IS31FL3733_I2C_ADDRESS_2 IS31FL3733_I2C_ADDRESS_GND_VCC
 
 #define IS31FL3733_DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 45

keyboards/acheron/apollo/87h/gamma/config.h

@@ -25,7 +25,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE
 
 // RGB Matrix defines
-#define DRIVER_ADDR_1 IS31FL3741_I2C_ADDRESS_GND
+#define IS31FL3741_I2C_ADDRESS_1 IS31FL3741_I2C_ADDRESS_GND
 
 #define IS31FL3741_DRIVER_COUNT 1
 #define DRIVER_1_LED_TOTAL 87

keyboards/aeboards/satellite/rev1/config.h

@@ -17,8 +17,8 @@
 #pragma once
 
 //RGB Matrix defines
-#define DRIVER_ADDR_1 IS31FL3731_I2C_ADDRESS_GND
-#define DRIVER_ADDR_2 IS31FL3731_I2C_ADDRESS_SDA
+#define IS31FL3731_I2C_ADDRESS_1 IS31FL3731_I2C_ADDRESS_GND
+#define IS31FL3731_I2C_ADDRESS_2 IS31FL3731_I2C_ADDRESS_SDA
 
 #define IS31FL3731_DRIVER_COUNT 2
 #define DRIVER_1_LED_TOTAL 36