Unexpected behavior of mailbox property "set power/domain state" #1894
Comments
|
Okay, i found one issue in the bcm2835-mailbox.c. The IRQ of the mailbox driver will be disabled during noirq suspend. So i used the IRQF_NO_SUSPEND flag for the IRQ request in order to prevent this. This fixed the timeouts during suspend, but now there is a timeout in resume: |
|
@ffainelli Any ideas/suggestions? |
|
@pelwell @popcornmix Do you have any idea why regarding to the second trace the "set power state" for USB runs into a timeout ( at 372.325785 ff)? |
|
My guess would be that the USB driver is not expecting to be closed then reopened. What is the aim of this investigation? |
|
My question relates to the unexpected behavior of "set power state": Yes, the DWC2 USB driver doesn't like it that the power state is not abled after resume. But these are just a consequential errors. The final goal of this investigation is support for suspend to idle (not suspend to RAM support), which is consider the "simplest" power management mode. I was able to "workaround" this specific issue by disabling DWC2 via device tree. In the meantime i extend the raspberrypi-power with a simple debugfs interface in order to enable and disable specific power domains incl. USB but i wasn't able to reproduce this timeout. So i'm not sure what's causing the USB power domain timeout. Maybe some timing issue. |
I was referring to the firmware's USB driver. |
|
Okay, but what should the difference between between manually disabling and re-enabling the power domain via debugfs which works fine and let suspend to idle doing this job. |
|
Have you followed the same sequence using debugfs that the suspend/resume cycle attempts? |
Fascinating. I wasn't aware that the VideoCore also had a USB driver and so both share the same resources. Btw there is a difference between my debugfs manual power domain scenario and suspend to idle. In the late suspend to idle first the USB IRQ (including all the other IRQs defined in the device tree) will be disabled in order to avoid wake ups and then the USB power domain will be disabled. Could this be the issue? |
There isn't one - it steps back, letting the ARMs take over.
Perhaps - if the firmware is waiting for an interrupt to indicate that some operation has completed. |
Is there times where you may want USB wake up such as from an input device? |
Yes, this is a special case which is hopefully handled properly by DWC2. But this is a future step. Currently the board freezes completely in suspend to idle even with debug UART as wake source. At first raspberrypi-power and the mailbox driver needs to be fixed. |
lategoodbye
added a commit
to lategoodbye/linux-dev
that referenced
this issue
Jun 23, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
lategoodbye
added a commit
to lategoodbye/linux-dev
that referenced
this issue
Jun 23, 2024
During supend to idle any request to power off the USB domain leads to a timeout. As a temporary workaround don't register the relevant power off handler. Link: raspberrypi/firmware#1894 Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
intel-lab-lkp
pushed a commit
to intel-lab-lkp/linux
that referenced
this issue
Jun 30, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
intel-lab-lkp
pushed a commit
to intel-lab-lkp/linux
that referenced
this issue
Jun 30, 2024
During supend to idle any request to power off the USB domain leads to a timeout. As a temporary workaround don't register the relevant power off handler. Link: raspberrypi/firmware#1894 Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
|
This issue was caused by the dwc2 driver and not by the VC4 firmware. The following draft patches should avoid the problem: |
lategoodbye
added a commit
to lategoodbye/linux-dev
that referenced
this issue
Jul 24, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
lategoodbye
added a commit
to lategoodbye/linux-dev
that referenced
this issue
Jul 25, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
lategoodbye
added a commit
to lategoodbye/linux-dev
that referenced
this issue
Aug 18, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
lategoodbye
added a commit
to lategoodbye/linux-dev
that referenced
this issue
Aug 20, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
lategoodbye
added a commit
to lategoodbye/linux-dev
that referenced
this issue
Aug 20, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
intel-lab-lkp
pushed a commit
to intel-lab-lkp/linux
that referenced
this issue
Aug 21, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty torvalds#17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
ColinIanKing
pushed a commit
to ColinIanKing/linux-next
that referenced
this issue
Sep 23, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
RobertCNelson
pushed a commit
to RobertCNelson/ti-linux-kernel
that referenced
this issue
Oct 4, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
johnny-mnemonic
pushed a commit
to linux-ia64/linux-stable-rc
that referenced
this issue
Oct 5, 2024
[ Upstream commit dc09f00 ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
johnny-mnemonic
pushed a commit
to linux-ia64/linux-stable-rc
that referenced
this issue
Oct 5, 2024
[ Upstream commit dc09f00 ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
johnny-mnemonic
pushed a commit
to linux-ia64/linux-stable-rc
that referenced
this issue
Oct 5, 2024
[ Upstream commit dc09f00 ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
oraclelinuxkernel
pushed a commit
to oracle/linux-uek
that referenced
this issue
Nov 22, 2024
[ Upstream commit dc09f00 ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> (cherry picked from commit b0de20de29b13950493a36bd4cf531200eb0e807) Signed-off-by: Sherry Yang <sherry.yang@oracle.com>
Ksawlii
pushed a commit
to Ksawlii/android_kernel_samsung_a53x-FireAsf
that referenced
this issue
Nov 23, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af6d704 ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ksawlii
pushed a commit
to Ksawlii/android_kernel_samsung_a53x-FireAsf
that referenced
this issue
Nov 23, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af6d704 ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
cat658011
pushed a commit
to cat658011/kernel-lts
that referenced
this issue
Nov 28, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fus0g
pushed a commit
to sm8350-martini/kernel_oneplus_sm8350
that referenced
this issue
Nov 29, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
DrBrown28
pushed a commit
to DrBrown28/Scalpel-LOS-20-KSU
that referenced
this issue
Dec 1, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
XeroMz69
pushed a commit
to XeroMz69/Bumi-Kernel-Tree
that referenced
this issue
Dec 1, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fluffball3
pushed a commit
to fluffball3/android_kernel_samsung_m33x
that referenced
this issue
Dec 2, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af6d704 ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The-Anomalist
pushed a commit
to The-Anomalist/Anomaly-Kernel
that referenced
this issue
Dec 4, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Nanhumly
pushed a commit
to Nanhumly-Staging/android_kernel_xiaomi_msm8998
that referenced
this issue
Dec 6, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ulrich Hecht <uli@kernel.org>
FakeShell
pushed a commit
to FuriLabs/linux-android-furiphone-krypton
that referenced
this issue
Dec 7, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
selfmusing
pushed a commit
to selfmusing/kernel_xiaomi_violet
that referenced
this issue
Dec 7, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
selfmusing
pushed a commit
to selfmusing/kernel_xiaomi_violet
that referenced
this issue
Dec 8, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sm8150
that referenced
this issue
Dec 9, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sdm845
that referenced
this issue
Dec 10, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_google_msm-4.14
that referenced
this issue
Dec 10, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
selfmusing
pushed a commit
to selfmusing/kernel_xiaomi_violet
that referenced
this issue
Dec 11, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fluffball3
pushed a commit
to fluffball3/android_kernel_samsung_m33x
that referenced
this issue
Dec 14, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af6d704 ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pckotzer
pushed a commit
to pckotzer/android_kernel_samsung_sm8550
that referenced
this issue
Dec 15, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sdm845
that referenced
this issue
Dec 18, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sdm845
that referenced
this issue
Dec 18, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sm8150
that referenced
this issue
Dec 18, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sdm845
that referenced
this issue
Dec 18, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_google_msm-4.14
that referenced
this issue
Dec 19, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_sony_sdm845
that referenced
this issue
Dec 19, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sdm845
that referenced
this issue
Dec 19, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sfX-bot
pushed a commit
to AXP-OS/android_kernel_oneplus_sm8150
that referenced
this issue
Dec 19, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
bojantanasic
pushed a commit
to bojantanasic/android_kernel_oneplus_sm8250
that referenced
this issue
Dec 22, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
alexeei
pushed a commit
to alexeei/kernel_xiaomi_lmi
that referenced
this issue
Dec 23, 2024
[ Upstream commit dc09f007caed3b2f6a3b6bd7e13777557ae22bfd ] During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sajattack
pushed a commit
to sajattack/android_kernel_oneplus_sdm845
that referenced
this issue
Dec 24, 2024
During noirq suspend phase the Raspberry Pi power driver suffer of firmware property timeouts. The reason is that the IRQ of the underlying BCM2835 mailbox is disabled and rpi_firmware_property_list() will always run into a timeout [1]. Since the VideoCore side isn't consider as a wakeup source, set the IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled during suspend-resume cycle. [1] PM: late suspend of devices complete after 1.754 msecs WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128 rpi_firmware_property_list+0x204/0x22c Firmware transaction 0x00028001 timeout Modules linked in: CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17 Hardware name: BCM2835 Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x44 dump_stack_lvl from __warn+0x88/0xec __warn from warn_slowpath_fmt+0x7c/0xb0 warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0 rpi_firmware_set_power from _genpd_power_off+0xe4/0x148 _genpd_power_off from genpd_sync_power_off+0x7c/0x11c genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0 genpd_finish_suspend from dpm_run_callback+0x78/0xd0 dpm_run_callback from device_suspend_noirq+0xc0/0x238 device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168 dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac suspend_devices_and_enter from pm_suspend+0x254/0x2e4 pm_suspend from state_store+0xa8/0xd4 state_store from kernfs_fop_write_iter+0x154/0x1a0 kernfs_fop_write_iter from vfs_write+0x12c/0x184 vfs_write from ksys_write+0x78/0xc0 ksys_write from ret_fast_syscall+0x0/0x54 Exception stack(0xcc93dfa8 to 0xcc93dff0) [...] PM: noirq suspend of devices complete after 3095.584 msecs Link: raspberrypi/firmware#1894 Fixes: 0bae6af ("mailbox: Enable BCM2835 mailbox support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Describe the bug
At first, i'm aware that suspend to idle isn't officially supported. Today i was playing around with suspend to idle on my Raspberry Pi 1B and noticed some strange behavior of mailbox property "set power/domain state" which is used by raspberry-power driver. The driver doesn't set the wait bit for the state. Since the properties are resume are replied it's not a firmware crash.
Does the driver have to care about the order while powering down a domain?
Did i missed something obvious?
To reproduce
Add "no_console_suspend" to cmdline.txt and reboot
Connect via Debug UART
echo 1 > /sys/power/pm_debug_messages
echo platform > /sys/power/pm_test
echo freeze > /sys/power/state
Expected behaviour
The power domains for USB, V3D, HDMI and VEC are powered down without timeout.
Actual behaviour
During entering of suspend state all mailbox properties timed out.
System
Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions:
vcgencmd version)? 2023-03-17T10:52:42uname -a)? 6.9.3Logs
The text was updated successfully, but these errors were encountered: