The Raspberry Pi GPIO Joystick Driver
The mk_arcade_joystick_rpi is fully integrated in the recalbox distribution : see http://www.recalbox.com
The branch hotkeybtn now support one more button per player in place of MCP23017 support
The RaspberryPi is an amazing tool I discovered a month ago. The RetroPie project made me want to build my own Arcade Cabinet with simple arcade buttons and joysticks.
So i started to wire my joysticks and buttons to my raspberry pi, and I wrote the first half of this driver in order to wire my joysticks and buttons directly to the RPi GPIOs.
However, the Raspberry Pi Board B Rev 2 has a maximum of 21 usable GPIOs, not enough to wire all the 28 switches (2 joystick and 20 buttons) that a standard panel requires.
UPDATE 0.1.5 : Added GPIO customization
UPDATE 0.1.4 : Compatibily with rpi2
UPDATE 0.1.3 : Compatibily with 3.18.3 :
The driver installation now works with 3.18.3 kernel, distributed with the last firmware.
UPDATE 0.1.2 : Downgrade to 3.12.28+ :
As the module will not load with recent kernel and headers, we add the possibility of downgrading your firmware to a compatible version, until we find a fix.
UPDATE 0.1.1 : RPi B+ VERSION :
The new Raspberry Pi B+ Revision brought us 9 more GPIOs, so we are now able to connect 2 joysticks and 12 buttons directly to GPIOs. I updated the driver in order to support the 2 joysticks on GPIO configuration.
A little cheap chip named MCP23017 allows you to add 16 external GPIO, and take only two GPIO on the RPi. The chip allows you to use GPIO as output or input, input is what we are looking for if we want even more joysticks.
If you want to use more than one chip, the i2c protocol lets you choose different addresses for the connected peripheral, but all use the same SDA and SCL GPIOs.
In theory you can connect up to 8 chips so 8 joystick.
The joystick driver is based on the gamecon_gpio_rpi driver by marqs
It is written for 4 directions joysticks and 8 buttons per player. Using a MCP23017 extends input numbers to 16 : 4 directions and 12 buttons.
It can read one joystick + buttons wired on RPi GPIOs (two on RPi B+ revision) and up to 5 other joysticks + buttons from MCP23017 chips. One MCP23017 is required for each joystick.
It uses internal pull-ups of RPi and of MCP23017, so all switches must be directly connected to its corresponding GPIO and to the ground.
Let's consider a 6 buttons cab panel with this button order :
↑ Ⓨ Ⓧ Ⓛ
← → Ⓑ Ⓐ Ⓡ
↓
With R = TR and L = TL
Here is the rev B GPIO pinout summary :
If you have a Rev B+ RPi or RPi2:
Of course the ground can be common for all switches.
Download the installation script :
mkdir mkjoystick
cd mkjoystick
wget https://github.com/recalbox/mk_arcade_joystick_rpi/releases/download/v0.1.4/install.shUpdate your system :
sudo sh ./install.sh updatesystem
sudo rebootDon't forget to reboot (or the next part won't work) and re-run the script without any arguments :
sudo sh ./install.shNow jump to Loading the driver
Update system :
sudo apt-get update
sudo apt-get upgrade
sudo rpi-update1 - Install all you need :
sudo apt-get install -y --force-yes dkms cpp-4.7 gcc-4.7 git joystick2 - Install last kernel headers :
sudo apt-get install -y --force-yes raspberrypi-kernel-headers3.a - Install driver from release (prefered):
wget https://github.com/recalbox/mk_arcade_joystick_rpi/releases/download/v0.1.4/mk-arcade-joystick-rpi-0.1.4.deb
sudo dpkg -i mk-arcade-joystick-rpi-0.1.4.deb3.b - Or compile and install with dkms:
3.b.1 - Download the files:
git clone https://github.com/pinuct/mk_arcade_joystick_rpi/tree/customgpio3.b.2 - Create a folder under "/usr/src/module-module-version/"
mkdir /usr/src/mk_arcade_joystick_rpi-0.1.5/3.b.3 - Copy the files into the folder:
cd mk_arcade_joystick_rpi/
cp -a * /usr/src/mk_arcade_joystick_rpi-0.1.5/3.b.4 - Compile and install the module:
dkms build -m mk_arcade_joystick_rpi -v 0.1.5
dkms install -m mk_arcade_joystick_rpi -v 0.1.5The driver is loaded with the modprobe command and take one parameter nammed "map" representing connected joysticks. When you will have to load the driver you must pass a list of parameters that represent the list of connected Joysticks. The first parameter will be the joystick mapped to /dev/input/js0, the second to js1 etc..
If you have connected a joystick on RPi GPIOs (joystick 1 on the pinout image) you must pass "map=1" as a parameter. If you are on B+ revision and you connected 2 joysticks you must pass map="1,2" as a parameter.
If you have one joystick connected on your RPi B or B+ version you will have to run the following command :
sudo modprobe mk_arcade_joystick_rpi map=1If you have two joysticks connected on your RPi B+ version you will have to run the following command :
sudo modprobe mk_arcade_joystick_rpi map=1,2If you have a TFT screen connected on your RPi B+ you can't use all the gpios. You can run the following command for using only the gpios not used by the tft screen (Be careful, not all tft screen use the same pins. GPIOs used with this map: 21,13,26, 19,5,6,22,4,20,17,27,16):
sudo modprobe mk_arcade_joystick_rpi map=4If you don't want to use all pins or wants a custom gpio map use:
sudo modprobe mk_arcade_joystick_rpi map=5 gpio=pin1,pin2,pin3,.....,pin12Where pinx is the number of the gpio you want. There are 12 posible gpio with button order: Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl. Use -1 for unused pins. For example gpio=21,13,26,19,-1,-1,22,24,-1,-1,-1,-1 uses gpios 21,13,26,19 for axis and gpios 22 and 24 for A and B buttons, the rest of buttons are unused.
The GPIO joystick 1 events will be reported to the file "/dev/input/js0" and the GPIO joystick 2 events will be reported to "/dev/input/js1"
Open /etc/modules :
sudo nano /etc/modulesand add the line you use to load the driver :
mk_arcade_joystick_rpiThen create the file /etc/modprobe.d/mk_arcade_joystick.conf :
sudo nano /etc/modprobe.d/mk_arcade_joystick.confand add the module configuration :
options mk_arcade_joystick_rpi map=1,2Use the following command to test joysticks inputs :
jstest /dev/input/js0Here is the MCP23017 pinout summary :
Follow the standards installation instructions.
Activate i2c on your RPi :
sudo nano /etc/modulesAdd the following lines in order to load i2c modules automatically :
i2c-bcm2708
i2c-devAnd if the file /etc/modprobe.d/raspi-blacklist.conf exists :
sudo nano /etc/modprobe.d/raspi-blacklist.confCheck if you have a line with :
i2c-bcm2708 and add a # at the beginning of the line to remove the blacklisting
Reboot or load the two module :
modprobe i2c-bcm2708 i2c-devYou must set the pins A0 A1 and A2 to 0 or 1 in order to set the i2c address of the chip. If you only have 1 chip, connect the 3 pins to the ground. Just connect one of the pins to 3.3v to set its state to 1 and change the i2c address of the MCP23017.
You must also connect the RESET pin to 3.3v.
When you want to load the driver you must pass a list of parameters that represent the list of connected Joysticks. The first parameter will be the joystick mapped to /dev/input/js0, the second to js1 etc..
If you have connected a joystick on RPi GPIOs you must pass "1" as a parameter.
If you have connected one or more joysticks with MCP23017, you must pass the address of I2C peripherals connected, which you can get with the command :
sudo i2cdetect -y 1The configuration of each MCP23017 is done by setting pads A0 A1 and A2 to 0 or 1.
If you configured your MCP23017 with A0 A1 and A2 connected to the ground, the address returned by i2cdetect should be 0x20
So if you have a joystick connected to RPi GPIOs and a joystick on a MCP23017 with the address 0x20, in order to load the driver, you must run the command :
sudo modprobe mk_arcade_joystick_rpi map=1,0x20The GPIO joystick events will be reported to the file "/dev/input/js0" and the mcp23017 joystick events will be reported to "/dev/input/js1"
I tested up to 3 joystick, one on GPIOs, one on a MCP23017 on address 0x20, one on a MCP23017 on address 0x24 :
sudo modprobe mk_arcade_joystick_rpi map=1,0x20,0x24If you try to read or write on i2c with a tool like i2cget or i2cset when the driver is loaded, you are gonna have a bad time...
If you try i2cdetect when the driver is running, it will show you strange peripheral addresses...
256MB Raspberry Pi Model B is not supported by the current driver. If you want to make the driver work on your old RPi, you will have to change the address of BSC1_BASE to (BCM2708_PERI_BASE + 0x205000) in order to use the correct i2c address, and recompile.
