-
Notifications
You must be signed in to change notification settings - Fork 173
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
SVXLINK holds transmit open for a long time #670
Comments
Hello,
First note is that you have PTT_HANGTIME=1000 which means it stays on for 1000 Milliseconds, suggest you reduce it to 10 or even 0.
Are you UK based?
Chris G4NAB
PS. New versions of the package is now 24.01.8
… On 10 Apr 2024, at 20:52, phlpittsny ***@***.***> wrote:
I have svxlink (version 19.09.1-3) working, to a point. But, when I elicit a response, it does not stop transmitting (i.e., it holds the PTT key down) for what seems like a long time. Need help, please.
System: Raspberry Pi 3B connected to a Baofeng UV-82 (primary radio) ... see below.
Secondary Baofeng UV-82 transmitting to the primary radio on 438.875MHz
Both radios set for CTCSS of 110.9Hz (Transmit AND Receive)
I start svxlink from the console of the RPi.
On the secondary radio I press PTT and then *# and the primary radio starts to transmit the
station identification, and on the console svxlink announces "Tx1: Turning the transmitter ON".
At the end of the station id, svxlink announces "Tx1: Turnng the transmitter OFF" ... but does
NOT stop transmitting for about a full minute.
Is this correct operation, or should the transmitter shut off sooner?
System details:
/etc/rpi-issue: on the RPi
Raspberry Pi reference 2024-03-12
Generated using pi-gen, https://github.com/RPi-Distro/pi-gen, b9b581e0a62afb7200d4b0b72ec2c43485fd49cc, stage4
from /etc/svxlink/svxlink.conf
Configured for PTT via GPIO18
[Tx1]
TYPE=Local
AUDIO_DEV=alsa:plughw:1
AUDIO_CHANNEL=0
#AUDIO_DEV_KEEP_OPEN=0
PTT_TYPE=GPIO
PTT_PORT=GPIO
PTT_PIN=gpio18
#HID_DEVICE=/dev/hidraw3
#HID_PTT_PIN=GPIO3
#SERIAL_SET_PINS=DTR!RTS
#GPIO_PATH=/sys/class/gpio
PTT_HANGTIME=1000
TIMEOUT=300
TX_DELAY=500
CTCSS_FQ=110.9
#CTCSS_LEVEL=9
PREEMPHASIS=0
DTMF_TONE_LENGTH=100
DTMF_TONE_SPACING=50
DTMF_DIGIT_PWR=-15
#MASTER_GAIN=0.0
#OB_AFSK_ENABLE=0
#OB_AFSK_VOICE_GAIN=-6
#OB_AFSK_LEVEL=-12
#OB_AFSK_TX_DELAY=100
#IB_AFSK_ENABLE=0
#IB_AFSK_LEVEL=-6
#IB_AFSK_TX_DELAY=100
The RPi is connected to the primary radio (BAOFENG UV-82) via an Easy Digi Kit
board with the following connections
Rpi to Digi Kit
Pin9 (GND) to Digi Kit Dig Gnd
Pin12 (GPIO18) to Digi Kit DTR
USB Sound Card MIC to Digi Kit "Audio to PC"
USB Sound Card SPK to Digi Kit "Audio from PC"
Digi Kit to Radio
Digi Kit Audio GND + MIC GND + PTT GND to Radio GND (2.5mm plug Shield (S of TRS))
Digi Kit Audio Out to Radio SPK+ (2.5mm plug Tip (T of TRS))
Digi Kit MIC IN to Radio Mic+ (3.5mm plug Ring (R of TRS))
Digi Kit PTT HI To Radio PTT (3.5mm plug Shield (S of TRS))
Thanks in advance for any help you can give.
—
Reply to this email directly, view it on GitHub <#670>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ACAKA5DRTWEEFLQ7OVTNBXTY4WJ7ZAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43ASLTON2WKOZSGIZTMMZSGA3DKMY>.
You are receiving this because you are subscribed to this thread.
|
Thanks... I'll try that. I'm in Rochester NY ... USA.
I have another problem if you can help... svxlink only responds to some
(not all) DTMF digits. Any ideas?
On Wed, Apr 10, 2024, 4:06 PM Chris G4NAB_F5VMR ***@***.***>
wrote:
… Hello,
First note is that you have PTT_HANGTIME=1000 which means it stays on for
1000 Milliseconds, suggest you reduce it to 10 or even 0.
Are you UK based?
Chris G4NAB
PS. New versions of the package is now 24.01.8
> On 10 Apr 2024, at 20:52, phlpittsny ***@***.***> wrote:
>
>
> I have svxlink (version 19.09.1-3) working, to a point. But, when I
elicit a response, it does not stop transmitting (i.e., it holds the PTT
key down) for what seems like a long time. Need help, please.
> System: Raspberry Pi 3B connected to a Baofeng UV-82 (primary radio) ...
see below.
> Secondary Baofeng UV-82 transmitting to the primary radio on 438.875MHz
> Both radios set for CTCSS of 110.9Hz (Transmit AND Receive)
> I start svxlink from the console of the RPi.
> On the secondary radio I press PTT and then *# and the primary radio
starts to transmit the
> station identification, and on the console svxlink announces "Tx1:
Turning the transmitter ON".
> At the end of the station id, svxlink announces "Tx1: Turnng the
transmitter OFF" ... but does
> NOT stop transmitting for about a full minute.
> Is this correct operation, or should the transmitter shut off sooner?
>
> System details:
> /etc/rpi-issue: on the RPi
> Raspberry Pi reference 2024-03-12
> Generated using pi-gen, https://github.com/RPi-Distro/pi-gen,
b9b581e0a62afb7200d4b0b72ec2c43485fd49cc, stage4
> from /etc/svxlink/svxlink.conf
> Configured for PTT via GPIO18
> [Tx1]
> TYPE=Local
> AUDIO_DEV=alsa:plughw:1
> AUDIO_CHANNEL=0
> #AUDIO_DEV_KEEP_OPEN=0
> PTT_TYPE=GPIO
> PTT_PORT=GPIO
> PTT_PIN=gpio18
> #HID_DEVICE=/dev/hidraw3
> #HID_PTT_PIN=GPIO3
> #SERIAL_SET_PINS=DTR!RTS
> #GPIO_PATH=/sys/class/gpio
> PTT_HANGTIME=1000
> TIMEOUT=300
> TX_DELAY=500
> CTCSS_FQ=110.9
> #CTCSS_LEVEL=9
> PREEMPHASIS=0
> DTMF_TONE_LENGTH=100
> DTMF_TONE_SPACING=50
> DTMF_DIGIT_PWR=-15
> #MASTER_GAIN=0.0
> #OB_AFSK_ENABLE=0
> #OB_AFSK_VOICE_GAIN=-6
> #OB_AFSK_LEVEL=-12
> #OB_AFSK_TX_DELAY=100
> #IB_AFSK_ENABLE=0
> #IB_AFSK_LEVEL=-6
> #IB_AFSK_TX_DELAY=100
>
> The RPi is connected to the primary radio (BAOFENG UV-82) via an Easy
Digi Kit
> board with the following connections
> Rpi to Digi Kit
> Pin9 (GND) to Digi Kit Dig Gnd
> Pin12 (GPIO18) to Digi Kit DTR
> USB Sound Card MIC to Digi Kit "Audio to PC"
> USB Sound Card SPK to Digi Kit "Audio from PC"
> Digi Kit to Radio
> Digi Kit Audio GND + MIC GND + PTT GND to Radio GND (2.5mm plug Shield
(S of TRS))
> Digi Kit Audio Out to Radio SPK+ (2.5mm plug Tip (T of TRS))
> Digi Kit MIC IN to Radio Mic+ (3.5mm plug Ring (R of TRS))
> Digi Kit PTT HI To Radio PTT (3.5mm plug Shield (S of TRS))
> Thanks in advance for any help you can give.
>
> —
> Reply to this email directly, view it on GitHub <
#670>, or unsubscribe <
https://github.com/notifications/unsubscribe-auth/ACAKA5DRTWEEFLQ7OVTNBXTY4WJ7ZAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43ASLTON2WKOZSGIZTMMZSGA3DKMY>.
> You are receiving this because you are subscribed to this thread.
>
—
Reply to this email directly, view it on GitHub
<#670 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AETURXYAE6GGAT3AFJAV6MTY4WLTTAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDANBYGM2DSNZTGQ>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Certainly - if you ensure the DEEMPHASIS=0 in the [Rx1] that may help.
Chris
… On 10 Apr 2024, at 22:36, phlpittsny ***@***.***> wrote:
Thanks... I'll try that. I'm in Rochester NY ... USA.
I have another problem if you can help... svxlink only responds to some
(not all) DTMF digits. Any ideas?
On Wed, Apr 10, 2024, 4:06 PM Chris G4NAB_F5VMR ***@***.***>
wrote:
> Hello,
>
> First note is that you have PTT_HANGTIME=1000 which means it stays on for
> 1000 Milliseconds, suggest you reduce it to 10 or even 0.
>
> Are you UK based?
>
> Chris G4NAB
>
> PS. New versions of the package is now 24.01.8
>
>
>
>
> > On 10 Apr 2024, at 20:52, phlpittsny ***@***.***> wrote:
> >
> >
> > I have svxlink (version 19.09.1-3) working, to a point. But, when I
> elicit a response, it does not stop transmitting (i.e., it holds the PTT
> key down) for what seems like a long time. Need help, please.
> > System: Raspberry Pi 3B connected to a Baofeng UV-82 (primary radio) ...
> see below.
> > Secondary Baofeng UV-82 transmitting to the primary radio on 438.875MHz
> > Both radios set for CTCSS of 110.9Hz (Transmit AND Receive)
> > I start svxlink from the console of the RPi.
> > On the secondary radio I press PTT and then *# and the primary radio
> starts to transmit the
> > station identification, and on the console svxlink announces "Tx1:
> Turning the transmitter ON".
> > At the end of the station id, svxlink announces "Tx1: Turnng the
> transmitter OFF" ... but does
> > NOT stop transmitting for about a full minute.
> > Is this correct operation, or should the transmitter shut off sooner?
> >
> > System details:
> > /etc/rpi-issue: on the RPi
> > Raspberry Pi reference 2024-03-12
> > Generated using pi-gen, https://github.com/RPi-Distro/pi-gen,
> b9b581e0a62afb7200d4b0b72ec2c43485fd49cc, stage4
> > from /etc/svxlink/svxlink.conf
> > Configured for PTT via GPIO18
> > [Tx1]
> > TYPE=Local
> > AUDIO_DEV=alsa:plughw:1
> > AUDIO_CHANNEL=0
> > #AUDIO_DEV_KEEP_OPEN=0
> > PTT_TYPE=GPIO
> > PTT_PORT=GPIO
> > PTT_PIN=gpio18
> > #HID_DEVICE=/dev/hidraw3
> > #HID_PTT_PIN=GPIO3
> > #SERIAL_SET_PINS=DTR!RTS
> > #GPIO_PATH=/sys/class/gpio
> > PTT_HANGTIME=1000
> > TIMEOUT=300
> > TX_DELAY=500
> > CTCSS_FQ=110.9
> > #CTCSS_LEVEL=9
> > PREEMPHASIS=0
> > DTMF_TONE_LENGTH=100
> > DTMF_TONE_SPACING=50
> > DTMF_DIGIT_PWR=-15
> > #MASTER_GAIN=0.0
> > #OB_AFSK_ENABLE=0
> > #OB_AFSK_VOICE_GAIN=-6
> > #OB_AFSK_LEVEL=-12
> > #OB_AFSK_TX_DELAY=100
> > #IB_AFSK_ENABLE=0
> > #IB_AFSK_LEVEL=-6
> > #IB_AFSK_TX_DELAY=100
> >
> > The RPi is connected to the primary radio (BAOFENG UV-82) via an Easy
> Digi Kit
> > board with the following connections
> > Rpi to Digi Kit
> > Pin9 (GND) to Digi Kit Dig Gnd
> > Pin12 (GPIO18) to Digi Kit DTR
> > USB Sound Card MIC to Digi Kit "Audio to PC"
> > USB Sound Card SPK to Digi Kit "Audio from PC"
> > Digi Kit to Radio
> > Digi Kit Audio GND + MIC GND + PTT GND to Radio GND (2.5mm plug Shield
> (S of TRS))
> > Digi Kit Audio Out to Radio SPK+ (2.5mm plug Tip (T of TRS))
> > Digi Kit MIC IN to Radio Mic+ (3.5mm plug Ring (R of TRS))
> > Digi Kit PTT HI To Radio PTT (3.5mm plug Shield (S of TRS))
> > Thanks in advance for any help you can give.
> >
> > —
> > Reply to this email directly, view it on GitHub <
> #670>, or unsubscribe <
> https://github.com/notifications/unsubscribe-auth/ACAKA5DRTWEEFLQ7OVTNBXTY4WJ7ZAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43ASLTON2WKOZSGIZTMMZSGA3DKMY>.
>
> > You are receiving this because you are subscribed to this thread.
> >
>
> —
> Reply to this email directly, view it on GitHub
> <#670 (comment)>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/AETURXYAE6GGAT3AFJAV6MTY4WLTTAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDANBYGM2DSNZTGQ>
> .
> You are receiving this because you authored the thread.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub <#670 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ACAKA5CHQPKWWQPGXPOVPEDY4WWFLAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDANBYGQ3TMOBZGM>.
You are receiving this because you commented.
|
I'll try that, too. Thanks...that helps a lot.
On Wed, Apr 10, 2024, 5:47 PM Chris G4NAB_F5VMR ***@***.***>
wrote:
… Certainly - if you ensure the DEEMPHASIS=0 in the [Rx1] that may help.
Chris
> On 10 Apr 2024, at 22:36, phlpittsny ***@***.***> wrote:
>
>
>
> Thanks... I'll try that. I'm in Rochester NY ... USA.
>
> I have another problem if you can help... svxlink only responds to some
> (not all) DTMF digits. Any ideas?
>
> On Wed, Apr 10, 2024, 4:06 PM Chris G4NAB_F5VMR ***@***.***>
> wrote:
>
> > Hello,
> >
> > First note is that you have PTT_HANGTIME=1000 which means it stays on
for
> > 1000 Milliseconds, suggest you reduce it to 10 or even 0.
> >
> > Are you UK based?
> >
> > Chris G4NAB
> >
> > PS. New versions of the package is now 24.01.8
> >
> >
> >
> >
> > > On 10 Apr 2024, at 20:52, phlpittsny ***@***.***> wrote:
> > >
> > >
> > > I have svxlink (version 19.09.1-3) working, to a point. But, when I
> > elicit a response, it does not stop transmitting (i.e., it holds the
PTT
> > key down) for what seems like a long time. Need help, please.
> > > System: Raspberry Pi 3B connected to a Baofeng UV-82 (primary radio)
...
> > see below.
> > > Secondary Baofeng UV-82 transmitting to the primary radio on
438.875MHz
> > > Both radios set for CTCSS of 110.9Hz (Transmit AND Receive)
> > > I start svxlink from the console of the RPi.
> > > On the secondary radio I press PTT and then *# and the primary radio
> > starts to transmit the
> > > station identification, and on the console svxlink announces "Tx1:
> > Turning the transmitter ON".
> > > At the end of the station id, svxlink announces "Tx1: Turnng the
> > transmitter OFF" ... but does
> > > NOT stop transmitting for about a full minute.
> > > Is this correct operation, or should the transmitter shut off
sooner?
> > >
> > > System details:
> > > /etc/rpi-issue: on the RPi
> > > Raspberry Pi reference 2024-03-12
> > > Generated using pi-gen, https://github.com/RPi-Distro/pi-gen,
> > b9b581e0a62afb7200d4b0b72ec2c43485fd49cc, stage4
> > > from /etc/svxlink/svxlink.conf
> > > Configured for PTT via GPIO18
> > > [Tx1]
> > > TYPE=Local
> > > AUDIO_DEV=alsa:plughw:1
> > > AUDIO_CHANNEL=0
> > > #AUDIO_DEV_KEEP_OPEN=0
> > > PTT_TYPE=GPIO
> > > PTT_PORT=GPIO
> > > PTT_PIN=gpio18
> > > #HID_DEVICE=/dev/hidraw3
> > > #HID_PTT_PIN=GPIO3
> > > #SERIAL_SET_PINS=DTR!RTS
> > > #GPIO_PATH=/sys/class/gpio
> > > PTT_HANGTIME=1000
> > > TIMEOUT=300
> > > TX_DELAY=500
> > > CTCSS_FQ=110.9
> > > #CTCSS_LEVEL=9
> > > PREEMPHASIS=0
> > > DTMF_TONE_LENGTH=100
> > > DTMF_TONE_SPACING=50
> > > DTMF_DIGIT_PWR=-15
> > > #MASTER_GAIN=0.0
> > > #OB_AFSK_ENABLE=0
> > > #OB_AFSK_VOICE_GAIN=-6
> > > #OB_AFSK_LEVEL=-12
> > > #OB_AFSK_TX_DELAY=100
> > > #IB_AFSK_ENABLE=0
> > > #IB_AFSK_LEVEL=-6
> > > #IB_AFSK_TX_DELAY=100
> > >
> > > The RPi is connected to the primary radio (BAOFENG UV-82) via an
Easy
> > Digi Kit
> > > board with the following connections
> > > Rpi to Digi Kit
> > > Pin9 (GND) to Digi Kit Dig Gnd
> > > Pin12 (GPIO18) to Digi Kit DTR
> > > USB Sound Card MIC to Digi Kit "Audio to PC"
> > > USB Sound Card SPK to Digi Kit "Audio from PC"
> > > Digi Kit to Radio
> > > Digi Kit Audio GND + MIC GND + PTT GND to Radio GND (2.5mm plug
Shield
> > (S of TRS))
> > > Digi Kit Audio Out to Radio SPK+ (2.5mm plug Tip (T of TRS))
> > > Digi Kit MIC IN to Radio Mic+ (3.5mm plug Ring (R of TRS))
> > > Digi Kit PTT HI To Radio PTT (3.5mm plug Shield (S of TRS))
> > > Thanks in advance for any help you can give.
> > >
> > > —
> > > Reply to this email directly, view it on GitHub <
> > #670>, or unsubscribe <
> >
https://github.com/notifications/unsubscribe-auth/ACAKA5DRTWEEFLQ7OVTNBXTY4WJ7ZAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43ASLTON2WKOZSGIZTMMZSGA3DKMY>.
> >
> > > You are receiving this because you are subscribed to this thread.
> > >
> >
> > —
> > Reply to this email directly, view it on GitHub
> > <#670 (comment)>,
> > or unsubscribe
> > <
https://github.com/notifications/unsubscribe-auth/AETURXYAE6GGAT3AFJAV6MTY4WLTTAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDANBYGM2DSNZTGQ>
> > .
> > You are receiving this because you authored the thread.Message ID:
> > ***@***.***>
> >
> —
> Reply to this email directly, view it on GitHub <
#670 (comment)>, or
unsubscribe <
https://github.com/notifications/unsubscribe-auth/ACAKA5CHQPKWWQPGXPOVPEDY4WWFLAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDANBYGQ3TMOBZGM>.
> You are receiving this because you commented.
>
>
—
Reply to this email directly, view it on GitHub
<#670 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AETURX26BMX66FYRJ6WV4SLY4WXPXAVCNFSM6AAAAABGBBODC6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDANBYGQ4TAOBQGQ>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
I have svxlink (version 19.09.1-3) working, to a point. But, when I elicit a response, it does not stop transmitting (i.e., it holds the PTT key down) for what seems like a long time. Need help, please.
System: Raspberry Pi 3B connected to a Baofeng UV-82 (primary radio) ... see below.
Secondary Baofeng UV-82 transmitting to the primary radio on 438.875MHz
Both radios set for CTCSS of 110.9Hz (Transmit AND Receive)
I start svxlink from the console of the RPi.
On the secondary radio I press PTT and then *# and the primary radio starts to transmit the
station identification, and on the console svxlink announces "Tx1: Turning the transmitter ON".
At the end of the station id, svxlink announces "Tx1: Turnng the transmitter OFF" ... but does
NOT stop transmitting for about a full minute.
Is this correct operation, or should the transmitter shut off sooner?
System details:
/etc/rpi-issue: on the RPi
Raspberry Pi reference 2024-03-12
Generated using pi-gen, https://github.com/RPi-Distro/pi-gen, b9b581e0a62afb7200d4b0b72ec2c43485fd49cc, stage4
from /etc/svxlink/svxlink.conf
Configured for PTT via GPIO18
[Tx1]
TYPE=Local
AUDIO_DEV=alsa:plughw:1
AUDIO_CHANNEL=0
#AUDIO_DEV_KEEP_OPEN=0
PTT_TYPE=GPIO
PTT_PORT=GPIO
PTT_PIN=gpio18
#HID_DEVICE=/dev/hidraw3
#HID_PTT_PIN=GPIO3
#SERIAL_SET_PINS=DTR!RTS
#GPIO_PATH=/sys/class/gpio
PTT_HANGTIME=1000
TIMEOUT=300
TX_DELAY=500
CTCSS_FQ=110.9
#CTCSS_LEVEL=9
PREEMPHASIS=0
DTMF_TONE_LENGTH=100
DTMF_TONE_SPACING=50
DTMF_DIGIT_PWR=-15
#MASTER_GAIN=0.0
#OB_AFSK_ENABLE=0
#OB_AFSK_VOICE_GAIN=-6
#OB_AFSK_LEVEL=-12
#OB_AFSK_TX_DELAY=100
#IB_AFSK_ENABLE=0
#IB_AFSK_LEVEL=-6
#IB_AFSK_TX_DELAY=100
The RPi is connected to the primary radio (BAOFENG UV-82) via an Easy Digi Kit
board with the following connections
Rpi to Digi Kit
Pin9 (GND) to Digi Kit Dig Gnd
Pin12 (GPIO18) to Digi Kit DTR
USB Sound Card MIC to Digi Kit "Audio to PC"
USB Sound Card SPK to Digi Kit "Audio from PC"
Digi Kit to Radio
Digi Kit Audio GND + MIC GND + PTT GND to Radio GND (2.5mm plug Shield (S of TRS))
Digi Kit Audio Out to Radio SPK+ (2.5mm plug Tip (T of TRS))
Digi Kit MIC IN to Radio Mic+ (3.5mm plug Ring (R of TRS))
Digi Kit PTT HI To Radio PTT (3.5mm plug Shield (S of TRS))
Thanks in advance for any help you can give.
The text was updated successfully, but these errors were encountered: