Add Delta Platform et-6248brb

device/delta/x86_64-delta_et-6248brb-r0/Delta-et-6248brb/port_config.ini

@@ -0,0 +1,51 @@
+# name         lanes              alias      index
+Ethernet0        1                1000       0
+Ethernet1        2                1000       1
+Ethernet2        3                1000       2
+Ethernet3        4                1000       3
+Ethernet4        5                1000       4
+Ethernet5        6                1000       5
+Ethernet6        7                1000       6
+Ethernet7        8                1000       7
+Ethernet8        9                1000       8
+Ethernet9        10               1000       9
+Ethernet10       11               1000       10
+Ethernet11       12               1000       11
+Ethernet12       13               1000       12
+Ethernet13       14               1000       13
+Ethernet14       15               1000       14
+Ethernet15       16               1000       15
+Ethernet16       17               1000       16
+Ethernet17       18               1000       17
+Ethernet18       19               1000       18
+Ethernet19       20               1000       19
+Ethernet20       21               1000       20
+Ethernet21       22               1000       21
+Ethernet22       23               1000       22
+Ethernet23       24               1000       23
+Ethernet24       25               1000       24
+Ethernet25       26               1000       25
+Ethernet26       27               1000       26
+Ethernet27       28               1000       27
+Ethernet28       29               1000       28
+Ethernet29       30               1000       29
+Ethernet30       31               1000       30
+Ethernet31       32               1000       31
+Ethernet32       33               1000       32
+Ethernet33       34               1000       33
+Ethernet34       35               1000       34
+Ethernet35       36               1000       35
+Ethernet36       37               1000       36
+Ethernet37       38               1000       37
+Ethernet38       39               1000       38
+Ethernet39       40               1000       39
+Ethernet40       41               1000       40
+Ethernet41       42               1000       41
+Ethernet42       43               1000       42
+Ethernet43       44               1000       43
+Ethernet44       45               1000       44
+Ethernet45       46               1000       45
+Ethernet46       47               1000       46
+Ethernet47       48               1000       47
+Ethernet48       54               10000      48
+Ethernet49       53               10000      49

device/delta/x86_64-delta_et-6248brb-r0/Delta-et-6248brb/sai.profile

@@ -0,0 +1 @@
+SAI_INIT_CONFIG_FILE=/etc/bcm/helix4-et-6248brb-48x1G+2x10G.config.bcm

device/delta/x86_64-delta_et-6248brb-r0/fancontrol

@@ -0,0 +1,12 @@
+INTERVAL=10
+DEVPATH=hwmon1=/sys/bus/i2c/devices
+DEVNAME=hwmon1=adt7473
+FCTEMPS=hwmon1/0-0048/hwmon/hwmon*/temp1_input hwmon1/7-0049/hwmon/hwmon*/temp1_input hwmon1/8-004a/hwmon/hwmon*/temp1_input
+
+FCFANS=hwmon1/0-002e/fan1_input hwmon1/0-002e/fan2_input
+
+FCTARGETS=hwmon1/0-002e/pwm1 hwmon1/0-002e/pwm2
+MINTEMP=20
+MAXTEMP=60
+MINSTART=75
+MINSTOP=22

device/delta/x86_64-delta_et-6248brb-r0/fancontrol.service

@@ -0,0 +1,279 @@
+#!/bin/bash
+#
+# Simple script implementing a temperature dependent fan speed control
+# Supported Linux kernel versions: 2.6.5 and later
+#
+# Version 0.70
+#
+# Usage: fancontrol [CONFIGFILE]
+#
+# Dependencies:
+#   bash, egrep, sed, cut, sleep, readlink, lm_sensors :)
+#
+# Please send any questions, comments or success stories to
+# marius.reiner@hdev.de
+# Thanks!
+#
+# For configuration instructions and warnings please see fancontrol.txt, which
+# can be found in the doc/ directory or at the website mentioned above.
+#
+#
+#    Copyright 2003 Marius Reiner <marius.reiner@hdev.de>
+#    Copyright (C) 2007-2009 Jean Delvare <khali@linux-fr.org>
+#
+#    This program is free software; you can redistribute it and/or modify
+#    it under the terms of the GNU General Public License as published by
+#    the Free Software Foundation; either version 2 of the License, or
+#    (at your option) any later version.
+#
+#    This program is distributed in the hope that it will be useful,
+#    but WITHOUT ANY WARRANTY; without even the implied warranty of
+#    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+#    GNU General Public License for more details.
+#
+#    You should have received a copy of the GNU General Public License
+#    along with this program; if not, write to the Free Software
+#    Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+#    MA 02110-1301 USA.
+#
+#
+
+PIDFILE="/var/run/fancontrol.pid"
+
+#DEBUG=1
+MAX=255
+
+function LoadConfig
+{
+	local fcvcount fcv
+
+	echo "Loading configuration from $1 ..."
+	if [ ! -r "$1" ]
+	then
+		echo "Error: Can't read configuration file" >&2
+		exit 1
+	fi
+
+	# grep configuration from file
+	INTERVAL=`egrep '^INTERVAL=.*$' $1 | sed -e 's/INTERVAL=//g'`
+	DEVPATH=`egrep '^DEVPATH=.*$' $1 | sed -e 's/DEVPATH= *//g'`
+	DEVNAME=`egrep '^DEVNAME=.*$' $1 | sed -e 's/DEVNAME= *//g'`
+	FCTEMPS=`egrep '^FCTEMPS=.*$' $1 | sed -e 's/FCTEMPS=//g'`
+	MINTEMP=`egrep '^MINTEMP=.*$' $1 | sed -e 's/MINTEMP=//g'`
+	MAXTEMP=`egrep '^MAXTEMP=.*$' $1 | sed -e 's/MAXTEMP=//g'`
+	MINSTART=`egrep '^MINSTART=.*$' $1 | sed -e 's/MINSTART=//g'`
+	MINSTOP=`egrep '^MINSTOP=.*$' $1 | sed -e 's/MINSTOP=//g'`
+	HWMON=$( echo "$DEVPATH" | sed 's/=.*$//g')
+	FCDEVPATH=$( echo "$DEVPATH" | sed 's/^.*=//g')
+	FCMINTEMP=$MINTEMP
+	FCMAXTEMP=$MAXTEMP
+	FCMINSTART=$MINSTART
+	FCMINSTOP=$MINSTOP
+	AFCTEMP_1_LOWER=(00 39 36 41 46 55)
+	AFCTEMP_1_UPPER=(39 39 44 49 54 150)
+	AFCTEMP_2_LOWER=(00 61 65 69 73 82)
+	AFCTEMP_2_UPPER=(63 67 71 75 79 150)
+	AFCTEMP_3_LOWER=(00 51 55 59 63 71)
+	AFCTEMP_3_UPPER=(53 57 61 65 69 150)
+
+
+	FCFANS=`egrep '^FCFANS=.*$' $1 | sed -e 's/FCFANS=//g'`
+
+	FCTARGETS=`egrep '^FCTARGETS=.*$' $1 | sed -e 's/FCTARGETS=//g'`
+
+	# Check whether all mandatory settings are set
+	if [[ -z ${INTERVAL} || -z ${FCTEMPS} || -z ${MINTEMP} || -z ${MAXTEMP} || -z ${MINSTART} || -z ${MINSTOP} ]]
+	then
+		echo "Some mandatory settings missing, please check your config file!" >&2
+		exit 1
+	fi
+	if [ "$INTERVAL" -le 0 ]
+	then
+		echo "Error in configuration file:" >&2
+		echo "INTERVAL must be at least 1" >&2
+		exit 1
+	fi
+
+	# write settings to arrays for easier use and print them
+	echo
+	echo "Common settings:"
+
+	temp_string=$FCTEMPS
+
+	let fcvcount=0
+	for fcv in $FCTEMPS
+	do
+		fcvcount=$((fcvcount+1))
+		AFCTEMP[$fcvcount]=$( echo "$temp_string" | cut -d" " -f $fcvcount )
+		AFCTEMP[$fcvcount]=$( echo "${AFCTEMP[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+		AFCTEMP_PATH[$fcvcount]=$( echo "${AFCTEMP[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+        	AFCTEMP[$fcvcount]=$( cat ${AFCTEMP[$fcvcount]} )
+		AFCTEMP[$fcvcount]=$(( AFCTEMP[$fcvcount]/1000 ))
+	done
+
+	fan_string=$FCFANS
+	fcvcount=0
+	for fcv in $FCFANS
+	do
+		fcvcount=$((fcvcount+1))
+		AFCFAN[$fcvcount]=$( echo "$fan_string" | cut -d" " -f $fcvcount )
+		AFCFAN_PATH[$fcvcount]=$( echo "${AFCFAN[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+		AFCFAN[$fcvcount]=$( cat ${AFCFAN_PATH[$fcvcount]} )
+	done
+
+	target_string=$FCTARGETS
+	fcvcount=0
+	for fcv in $FCTARGETS
+	do
+		fcvcount=$((fcvcount+1))
+		AFCTARGET[$fcvcount]=$( echo "$target_string" | cut -d" " -f $fcvcount )
+		AFCFAN_TARGET[$fcvcount]=$( echo "${AFCTARGET[$fcvcount]}" | sed 's/hwmon1/\/sys\/bus\/i2c\/devices/g' )
+	done
+
+}
+
+# Check that all referenced sysfs files exist
+function CheckFiles
+{
+	local outdated=0 fcvcount tsen fan
+	if [ $outdated -eq 1 ]
+	then
+		echo >&2
+		echo "At least one referenced file is missing. Either some required kernel" >&2
+		echo "modules haven't been loaded, or your configuration file is outdated." >&2
+		echo "In the latter case, you should run pwmconfig again." >&2
+	fi
+	return $outdated
+}
+
+LoadConfig $1
+
+# Detect path to sensors
+if [ ! -d $DIR ]
+then
+	echo $0: 'No sensors found! (did you load the necessary modules?)' >&2
+	exit 1
+fi
+cd $DIR
+
+# Check for configuration change
+if [ "$DIR" != "/" ] && [ -z "$DEVPATH" -o -z "$DEVNAME" ]
+then
+	echo "Configuration is too old, please run pwmconfig again" >&2
+	exit 1
+fi
+if [ "$DIR" = "/" -a -n "$DEVPATH" ]
+then
+	echo "Unneeded DEVPATH with absolute device paths" >&2
+	exit 1
+fi
+CheckFiles || exit 1
+
+if [ -f "$PIDFILE" ]
+then
+	echo "File $PIDFILE exists, is fancontrol already running?" >&2
+	exit 1
+fi
+echo $$ > "$PIDFILE"
+
+# main function
+function UpdateThermalSensors
+{
+	fcvcount=0
+	for fcv in $FCTEMPS
+	do
+		fcvcount=$((fcvcount+1))
+        	AFCTEMP[$fcvcount]=$( cat ${AFCTEMP_PATH[$fcvcount]} )
+		AFCTEMP[$fcvcount]=$(( AFCTEMP[$fcvcount]/1000 ))
+	done
+}
+
+function UpdateThermalLevel
+{
+	AFCTEMP_NUM=$((6-${AFCTEMP_LEVEL[$i]}))
+ 	AFCTEMP_UPPER_BUF=AFCTEMP_"$i"_UPPER["$AFCTEMP_NUM"]
+ 	AFCTEMP_LOWER_BUF=AFCTEMP_"$i"_LOWER["$AFCTEMP_NUM"]
+
+	AFCTEMP_UPPER=${!AFCTEMP_UPPER_BUF}
+ 	AFCTEMP_LOWER=${!AFCTEMP_LOWER_BUF}
+
+
+	if (( ("${AFCTEMP[$i]}" <= "$AFCTEMP_UPPER") && ("${AFCTEMP[$i]}" >= "$AFCTEMP_LOWER") )) ; then 
+	    FLAG=2
+	elif (( "${AFCTEMP[$i]}" > "$AFCTEMP_UPPER" )); then 
+	    AFCTEMP_LEVEL[$i]=$((${AFCTEMP_LEVEL[$i]} - 1))
+	    FLAG=1
+	elif (( "${AFCTEMP[$i]}" < "$AFCTEMP_LOWER" )); then     
+		AFCTEMP_LEVEL[$i]=$((${AFCTEMP_LEVEL[$i]} + 1))
+		FLAG=1
+	else
+		AFCTEMP_LEVEL[$i]=1
+		FLAG=2
+	fi
+}
+
+function UpdateFanSpeeds
+{
+	#echo "num tmp lev  F   L   H"
+	#Update level
+	for i in 1 2 3
+	do
+		#echo "----------------------"
+		FLAG=0
+		#FLAG=0 : initial flag
+		#FLAG=1 : update level
+		#FLAG=2 : final level
+		while [ $FLAG -ne 2 ]
+		do
+			UpdateThermalLevel
+			#echo " $i  ${AFCTEMP[$i]}   ${AFCTEMP_LEVEL[$i]}   $FLAG  $AFCTEMP_LOWER  $AFCTEMP_UPPER "
+		done
+	done
+
+	min=${AFCTEMP_LEVEL[0]}
+	for j in "${AFCTEMP_LEVEL[@]}"; do
+	  (( j < min )) && min=$j
+	done
+
+	if (($min == 1 || $min == 2)); then 
+    	FAN_PERCENTAGE=100
+	elif (($min == 3)); then 
+	    FAN_PERCENTAGE=80
+	elif (($min == 4)); then
+	    FAN_PERCENTAGE=60
+	elif (($min == 5)); then
+	    FAN_PERCENTAGE=40
+	elif (($min == 6)); then
+	    FAN_PERCENTAGE=30
+	else
+	    FAN_PERCENTAGE=100
+	fi
+	echo "The lowest level of thermal sensors: $min "
+	echo "Trying to set fan speed to $FAN_PERCENTAGE %"
+	#Set speed to fan1~fan10
+	FAN_PERCENTAGE=`expr $FAN_PERCENTAGE \* 255 / 100`
+	let fcvcount=0
+	for fcv in $FCFANS
+	do
+		fcvcount=$(( fcvcount + 1 ))
+		echo  $FAN_PERCENTAGE > ${AFCFAN_TARGET[$fcvcount]} 
+		AFCFAN[$fcvcount]=$( cat ${AFCFAN_PATH[$fcvcount]} )
+
+		echo "FAN fan$fcvcount = ${AFCFAN[$fcvcount]} (rpm)"
+	done
+
+	rm -f "$PIDFILE"
+}
+
+# main loop calling the main function at specified intervals
+AFCTEMP_LEVEL=(9 4 4 4) #inttial level
+while true
+do
+	UpdateThermalSensors
+	UpdateFanSpeeds
+	echo "Sleep $INTERVAL seconds ..."
+	echo
+	# Sleep while still handling signals
+	sleep $INTERVAL &
+	wait $!
+done

device/delta/x86_64-delta_et-6248brb-r0/installer.conf

@@ -0,0 +1,3 @@
+CONSOLE_PORT=0x2f8
+CONSOLE_DEV=1
+CONSOLE_SPEED=115200

device/delta/x86_64-delta_et-6248brb-r0/led_proc_init.soc

@@ -0,0 +1,46 @@
+#ET_6248BRB Port_Remap
+# Vlan set and port enable
+clear c
+port ge en=1
+port hg en=1
+
+# led0 port order remap
+m CMIC_LEDUP0_PORT_ORDER_REMAP_0_3 REMAP_PORT_0=0 REMAP_PORT_1=1 REMAP_PORT_2=2 REMAP_PORT_3=3
+m CMIC_LEDUP0_PORT_ORDER_REMAP_4_7 REMAP_PORT_4=4 REMAP_PORT_5=5 REMAP_PORT_6=6 REMAP_PORT_7=7
+m CMIC_LEDUP0_PORT_ORDER_REMAP_8_11 REMAP_PORT_8=51 REMAP_PORT_9=50 REMAP_PORT_10=49 REMAP_PORT_11=48
+m CMIC_LEDUP0_PORT_ORDER_REMAP_12_15 REMAP_PORT_12=47 REMAP_PORT_13=46 REMAP_PORT_14=45 REMAP_PORT_15=44
+m CMIC_LEDUP0_PORT_ORDER_REMAP_16_19 REMAP_PORT_16=43 REMAP_PORT_17=42 REMAP_PORT_18=41 REMAP_PORT_19=40
+m CMIC_LEDUP0_PORT_ORDER_REMAP_20_23 REMAP_PORT_20=39 REMAP_PORT_21=38 REMAP_PORT_22=37 REMAP_PORT_23=36
+m CMIC_LEDUP0_PORT_ORDER_REMAP_24_27 REMAP_PORT_24=35 REMAP_PORT_25=34 REMAP_PORT_26=33 REMAP_PORT_27=32
+m CMIC_LEDUP0_PORT_ORDER_REMAP_28_31 REMAP_PORT_28=31 REMAP_PORT_29=30 REMAP_PORT_30=29 REMAP_PORT_31=28
+m CMIC_LEDUP0_PORT_ORDER_REMAP_32_35 REMAP_PORT_32=27 REMAP_PORT_33=26 REMAP_PORT_34=25 REMAP_PORT_35=24
+m CMIC_LEDUP0_PORT_ORDER_REMAP_36_39 REMAP_PORT_36=23 REMAP_PORT_37=22 REMAP_PORT_38=21 REMAP_PORT_39=20
+m CMIC_LEDUP0_PORT_ORDER_REMAP_40_43 REMAP_PORT_40=19 REMAP_PORT_41=18 REMAP_PORT_42=17 REMAP_PORT_43=16
+m CMIC_LEDUP0_PORT_ORDER_REMAP_44_47 REMAP_PORT_44=15 REMAP_PORT_45=14 REMAP_PORT_46=13 REMAP_PORT_47=12
+m CMIC_LEDUP0_PORT_ORDER_REMAP_48_51 REMAP_PORT_48=11 REMAP_PORT_49=10 REMAP_PORT_50=9 REMAP_PORT_51=8
+m CMIC_LEDUP0_PORT_ORDER_REMAP_52_55 REMAP_PORT_52=7 REMAP_PORT_53=6 REMAP_PORT_54=5 REMAP_PORT_55=4
+m CMIC_LEDUP0_PORT_ORDER_REMAP_56_59 REMAP_PORT_56=3 REMAP_PORT_57=2 REMAP_PORT_58=1 REMAP_PORT_59=0
+m CMIC_LEDUP0_PORT_ORDER_REMAP_60_63 REMAP_PORT_60=60 REMAP_PORT_61=61 REMAP_PORT_62=62 REMAP_PORT_63=63
+
+echo "ET_6248BRB LED Port Remap: Done."
+
+#ET_6248BRB_LED
+
+#--------------------------------------------------------------------------------------------------
+#LED Auto link/up
+
+led stop
+led prog '\
+ 02 00 60 E0 02 A0 60 E2 86 E6 02 00 60 E1 06 E0\
+ D2 30 75 28 02 00 2E E0 32 08 97 71 1F 77 44 2E\
+ E0 32 04 97 71 3C 77 40 02 00 2E E0 32 08 97 71\
+ 33 77 44 2E E0 32 03 97 71 3C 77 40 02 02 77 44\
+ 02 04 77 44 60 E3 2E E0 32 00 32 01 B7 97 02 00\
+ 0E 00 12 E4 FE E1 50 12 E4 05 60 E5 12 E3 05 0A\
+ 02 71 67 67 9A 77 69 67 86 12 E3 05 0A 01 71 74\
+ 67 9A 77 76 67 86 06 E2 F2 01 60 E2 86 E0 06 E0\
+ D2 34 74 0A 3A 68 06 E5 D2 00 70 96 16 E6 99 99\
+ 1A 00 71 96 77 9A 32 0F 87 57 32 0E 87 57 00 00\
+'
+led auto on
+led start