Skip to content

Tutorial SensorClientRaspberryPi WindSpeed

sqall01 edited this page Apr 11, 2023 · 2 revisions

Tutorial - AlertR Sensor Client Raspberry Pi - Wind Speed

(For version 1.002)

This tutorial describes the basic configuration of the AlertR Sensor Client Raspberry Pi with a connected to a wind speed sensor. It can be used as foundation to develop an own AlertR system setup. This tutorial assumes you have set up the AlertR Server according to the provided Server Tutorial.

Table of Contents

Description

The client is described as the following by the installation:

sqall@towel:~$ ./alertRinstaller.py -l

[...]
AlertR Sensor Client Raspberry Pi
---------------------------------
Instance:
sensorClientRaspberryPi

Type:
sensor

Version:
0.901-0

Dependencies:
1: requests (pip packet: requests) (lowest version: 2.20.0)
2: RPi.GPIO (pip packet: RPi.GPIO) (lowest version: 0.5.2)

Description:
This client handles Raspberry Pi GPIO pins as sensors. It either polls the state of a GPIO pin or uses an interrupt on a falling/rising edge and triggers an alert if the state has changed/interrupt has occurred (or a state change if it goes back from a state in which it triggers an alert to a normal state). This means it notifies the server if an alert was triggered by a sensor. A sensor connected to the GPIO pin can be anything you like, for example, a PIR (Passive InfraRed) sensor, a magnetic switch on a window, a water leak alarm sensor, a smoke detector and so on. Furthermore, this client also supports DS18B20 temperature sensors.
[...]

Installation

In order to install the AlertR Sensor Client Raspberry Pi, we first have to fulfill all prerequisites. On a Debian/Ubuntu Linux you can install everything with the following commands:

root@towel:/home/sqall# apt-get install python3-pip

root@towel:/home/sqall# pip3 install RPi.GPIO requests

Obviously, the AlertR Sensor Client Raspberry Pi should be installed on a Raspberry Pi. Please note that older versions of the Raspberry Pi packages need "root" permissions in order to access the GPIO pins. If you are installing the AlertR instance on an older Raspberry Pi operating system with older packages, make sure it works without "root" permissions before creating a new user account for the AlertR instance. If it only works with "root" permissions, please omit all steps that use the new "alertr" user and instead use the "root" user account.

It is always a good idea to have an own user for a daemon. Therefore, we create a user that runs the AlertR Sensor Client Raspberry Pi called "alertr":

root@towel:/home/sqall# adduser --disabled-password alertr
Adding user `alertr' ...
Adding new group `alertr' (1002) ...
Adding new user `alertr' (1002) with group `alertr' ...
Creating home directory `/home/alertr' ...
Copying files from `/etc/skel' ...
Changing the user information for alertr
Enter the new value, or press ENTER for the default
    Full Name []:
    Room Number []:
    Work Phone []:
    Home Phone []:
    Other []:
Is the information correct? [Y/n] y

Additionally, the user has to be in the group gpio in order to access the GPIO pins:

root@towel:/home/sqall# addgroup alertr gpio

To switch into this user in the terminal you can use the following command:

root@towel:/home/sqall# su alertr

Please note that this is only possible as root user. If you are trying this command as another user you will get a password prompt for the user alertr, which does not have a password.

Afterwards, you can use the installation script provided by AlertR to install the client.

alertr@towel:~$ wget https://raw.githubusercontent.com/sqall01/alertR/master/alertRinstaller.py

alertr@towel:~$ mkdir sensorClientRaspberryPi

alertr@towel:~$ chmod 755 alertRinstaller.py

alertr@towel:~$ ./alertRinstaller.py -i sensorClientRaspberryPi -t ./sensorClientRaspberryPi/

Setup

This tutorial connects a wind speed sensor (aka anemometer) to the Raspberry Pi. The sensor will measure the current wind speed as well as the wind gust. To measure the wind speed the sensor behaves like a switch which closes during a rotation (or it closes multiple times in one rotation). If you are interested, this technique and how to calculate the wind speed from it is described in more detail in this official Raspberry Pi tutorial. For this tutorial, we do not need to know the details since the AlertR Sensor Client Raspberry Pi does all the calculations for us.

The circuit diagram to connect the wind sensor to the Raspberry Pi looks like this:

Raspberry Pi Wind Speed

If you set this up in your garden it could look like the following:

raspberry pi outside wind speed sensor 1 wind speed sensor 2

Let us assume for this tutorial, the wind speed sensor is connected to GPIO pin 24. A picture of the pin numbers can be found on this website (for the Raspberry Pi Model B/B+). The pin number is the actual number of the pin and not the name of the pin (since the name changes depending on the used Raspberry Pi revision). This means on the picture, the GPIO pin 24 is the one with the name "GPIO8 / SP10_CE0_N".

A helper script to check the correct GPIO configuration is provided by the installation in the directory /home/alertr/sensorClientRaspberryPi/helperScripts. The script raspberryPiGpioInputTest.py has to be modified to check the correct GPIO pin.

[...]

# NOTE: this is the actual pin number (not the number of the GPIO)
inputPin = 24

[...]

When we execute the script and rotate the wind speed sensor, the output looks like the following:

alertr@towel:~/sensorClientRaspberryPi/helperScripts$ python3 raspberryPiGpioInputTest.py 
0
0
1
1
0
0
1
1
1
0
0
1
1
1
1
0
0
1
1
[...]

Furthermore, to configure the wind speed calculation correctly, you have to take a look at the data sheet of your sensor and get the following values:

  • radius of the arms holding the scoops of your sensor
  • number of signals per rotation

If you do not have a data sheet available that does provide the values, you can simply measure the radius yourself. For the number of signals per rotation, just run the script mentioned above and do one rotation of the wind speed sensor. Then we count the changes from 0 to 1 in the output of the script.

For this tutorial, we assume that the radius is 6.15 cm and we have 2 signals per rotation.

Configuration

The following describes the configuration of the AlertR Sensor Client Raspberry Pi. It shows a basic configuration that can be used as a template for own installations.

Certificate

For security reasons, it is strongly recommended to use a TLS connection for your AlertR system. Hence, all tutorials will use TLS. However, for testing purposes AlertR gives you the option to disable TLS. If you do so, you have to disable it for the complete AlertR system.

During the installation of the AlertR server, you created a certificate file with the name alertr_server.crt. This file is needed by the client in order to verify the connection. Please copy it to the host you are installing this client on. This tutorial assumes that you have stored the certificate file in the following location: /home/alertr/sensorClientRaspberryPi/config/alertr_server.crt.

User Credentials

The client has to authenticate itself before it can work with the server. Therefore, we need to set up user credentials on the AlertR server for this client. We execute the following command with the manageUsers.py script of the server which is located in the installation directory of the server (see Users Management for further information):

alertr@towel:/home/alertr/server# ./manageUsers.py -a -u user_pi -p password_pi -t sensor -i sensorClientRaspberryPi

Please make sure that the AlertR Server is not running while adding a user.
Otherwise it can lead to an inconsistent state and a corrupted database.
Are you sure to continue?
(y/n): y

Alert Levels

This tutorial assumes the Alert Levels configured in the AlertR Server tutorial. The client will use the following for its configuration:

Alert Level Name Profiles Functionality
0 Dummy Activated, Deactivated Used for sensors that do not trigger.
1 Silent Notification Activated, Deactivated Used to silently notify the user.

Alert Level 0 is used for the wind gust that should not trigger any Sensor Alert.

Alert Level 1 is used for the current wind speed that triggers a Sensor Alert if it is above a certain threshold, but not an urgent one. This Alert Level is member of every System Profile and thus triggers always.

Configuration File

Every AlertR installation has a template configuration file with detailed comments that describe the functionality of each option. To use it as a draft, you can just copy the template file and modify your new configuration file.

alertr@towel:~/sensorClientRaspberryPi/config$ cp config.xml.template config.xml

alertr@towel:~/sensorClientRaspberryPi/config$ chmod 700 config.xml

The configuration file itself is split into the following parts:

  • General
  • SMTP
  • Update
  • Sensors

In this tutorial, we are going through each of these parts separately and describe why we configured it like that.

General

The general section is used for options such as certificate file location. In our tutorial configuration, the section looks like this:

    <general>

        <log
            file="./logfile.log"
            level="INFO" />

        <server
            host="localhost"
            port="44556" />

        <ssl
            enabled="True">

            <server
                caFile="./config/alertr_server.crt" />

            <client
                certificateRequired="False"
                certFile="/path/to/client.crt"
                keyFile="/path/to/client.key" />
        </ssl>

        <credentials
            username="user_pi"
            password="password_pi" />

        <connection
            persistent="True" />

    </general>

Section log is used to configure the log file setup. The file attribute sets the location for the log file. Make sure it exists and is writable by the user that starts the AlertR client. Otherwise the client will not start. For example, the directory /var/log is usually only writable by the "root" user and users of the group "syslog". If you want the client log file in this directory, please create a sub-directory for the AlertR client log file and set the correct permissions on it. The level attribute sets the log level. Possible values are DEBUG, INFO, WARNING, ERROR, CRITICAL.

Section server is used to configure the server connection setup. The host and port attribute sets the address and port of the AlertR server. The port was previously configured in the server configuration file. The address can either be a name that can be resolved by the DNS system or an IP address.

Section ssl is used to configure the TLS/SSL setup. The enabled attributes gives you the option to disable or enable it. This setting has to be the same for your complete AlertR setup. It is strongly recommended to enable TLS/SSL and only disable it in a testing environment. In this tutorial, we enable TLS/SSL. The caFile attribute in the server section sets the location of the certificate file that is used to authenticate the server (see Certificate). Section client is used to configure the client connection setup. The certificateRequired attribute determines if the client needs a certificate to connect to the server or not. The certFile and keyFile are used to determine the client certificate and key file. Since this tutorial is not using client certificates, we do not have to set sane values here.

Section credentials is used to configure the login credentials of this client. The credentials were configured in a previous step of this Tutorial and must be the same as in this configuration file.

Section connection is used to configure the connection to the server. The persistent attribute is used to configure if the connection to the server has to be persistent. This means that if the client disconnects, a Sensor Alert is created by the server.

SMTP

The smtp section is used for options that configure the used SMTP server. In our tutorial configuration, the section looks like this:

    <smtp>

        <general
            activated="True"
            fromAddr="sensorClientRaspberryPi@alertr.de"
            toAddr="myalarmaddress@example.org" />

        <server
            host="127.0.0.1"
            port="25" />

    </smtp>

Section general is used to configure the basic options of the eMail notification. The eMail notification is used if problems on the AlertR client occur that can not be solved (like connection problems). The activated attribute determines if the eMail notification is activated or not. If it is deactivated, the rest of the options in the whole smtp section are ignored. The fromAddr attribute sets the used eMail address from which the eMail notification is sent. The toAddr attribute determines the eMail address the notification is sent to.

Section server is used to configure the SMTP server that is used to send the eMail notification. The host attribute sets the address and the port attribute sets the port of the used SMTP server. At the moment, only "127.0.0.1" is allowed as address and port 25. This means you have to set up a local SMTP server in order to send eMail notifications. Personally, I would suggest to set up a local Postfix SMTP server that can forward eMails like in this Tutorial. Please note that the local SMTP server has to accept eMails from localhost without any authentication since it is not supported by AlertR yet.

Update

The update section is used to give the online repository for updates. In our tutorial configuration, the section looks like this:

    <update>

        <server
            url="https://raw.githubusercontent.com/sqall01/alertR/master/" />

    </update>

Section server is used to configure the remote update repository. Normally, the default configuration can be used here (which is this repository). The url attribute gives the remote server location of the repository. Only the https protocol is allowed here if you want to change it.

Sensors

The sensors section configures the sensors of this client. In our tutorial configuration, the section looks like this:

    <sensors>

        <sensor>

            <general
                id="0"
                description="Wind Gust (Last 6h)"
                alertDelay="0"
                triggerAlert="False"
                triggerAlertNormal="False" />

            <alertLevel>0</alertLevel>

            <gpio
                type="windspeed"
                sensorAlertForDataChange="False"
                gpioPin="24"
                interval="60"
                radius="6.15"
                signalsPerRotation="2"
                onlyMaxInterval="21600"
                hasThreshold="False"
                threshold="40.0"
                ordering="GT" />

        </sensor>

        <sensor>

            <general
                id="1"
                description="Wind Speed"
                alertDelay="0"
                triggerAlert="True"
                triggerAlertNormal="True" />

            <alertLevel>1</alertLevel>

            <gpio
                type="windspeed"
                sensorAlertForDataChange="False"
                gpioPin="24"
                interval="60"
                radius="6.15"
                signalsPerRotation="2"
                onlyMaxInterval="0"
                hasThreshold="True"
                threshold="40.0"
                ordering="GT" />

        </sensor>

    </sensors>

Each configured sensor is set up in its own <sensor>...</sensor> context. The context has three main sections: general, alertLevel and gpio. The following describes the settings of each section.

Section general is used to configure the basic sensor settings. The id attribute gives the local id of the configured sensor. This id has to be unique for each sensor of this client. Since we configure two sensors, we give them the id 0 and 1. The description attribute gives a short description of the sensor. The alertDelay attribute sets how long in seconds the server has to wait until a Sensor Alert is triggered. Normally, this is set to 0 to immediate react on a Sensor Alert. But in some situations it might be necessary to react on a Sensor Alert after a certain time and not directly. For our tutorial sensors we set this value to 0. The triggerAlert attribute sets if the sensor triggers a Sensor Alert with the state "triggered" and triggerAlertNormal sets if the sensor triggers a Sensor Alert with the state "normal". The wind gust sensor should trigger no Sensor Alert at all, whereas the current wind speed should trigger the "triggered" and "normal" Sensor Alert.

The alertLevel sections set the Alert Level the sensor triggers. In our tutorial, one sensor triggers Alert Level 0 and one Alert Level 1. But it is not limited to only one Alert Level per sensor. If another Alert Level should be triggered, an additional alertLevel section is added with the corresponding Alert Level.

Section gpio configures the GPIO sensor settings. The type attribute sets the type of the GPIO sensor. In both cases, this is set to "windspeed". The "windspeed" type calculates the wind speed of an anemometer. The sensorAlertForDataChange attribute sets if a Sensor Alert event should be sent to the AlertR system with the newest measured data or a State Change event. AlertR is an event driven system, hence, this can be useful if you want to instrument the data the sensor is holding in instrumentation scripts since these are only executed if a Sensor Alert event is processed. However, in our tutorial we only want the newest data in our system and set this attribute to "False". The gpioPin attribute sets the number of the pin that is used. In our tutorial, the anemometer is connected to the pin 24. The interval attributes gives the interval in seconds in which the new wind speed data is sent to the AlertR system for processing. The radius attributes sets the radius of your wind speed sensor in cm. In our tutorial it is set to 6.15 cm. The signalsPerRotation gives the number of signals the wind speed sensor creates for one rotation. In our tutorial the anemometer creates 2 signals per rotation. The onlyMaxInterval sets if only the highest measured wind speed is sent to the AlertR system in the given interval in seconds. This allows you to measure wind gusts. In our tutorial, one sensor sends the current wind speed to the AlertR system by setting the onlyMaxInterval to 0 and the other measures the wind gust in the last 6 hours by setting this attribute to 21600 seconds. The hasThreshold attribute sets if this sensor has a threshold which could be exceeded. In this tutorial, the Wind Gust (Last 6h) sensor has none (and therefore does not trigger any Sensor Alert) and the Wind Speed has one. The threshold attribute sets the wind speed that triggers a Sensor Alert when exceeded. The ordering attribute sets what kind of threshold we have set. In our tutorial, the Wind Speed should trigger a Sensor Alert if the current wind speed is greater (GT = greater than) 40 km/h. This can be useful, for example, if we have breakable things in our garden that need to be secured if the wind speed increases.

Autostart

If you want the AlertR client to start automatically after a reboot of the host, you have to set it up. In this tutorial, I will give two examples on how to set up the autostart of the AlertR client depending on your system using systemd or just init.d.

Init.d

An init.d script is provided by the AlertR installation. The only thing you have to do is to copy and configure it correctly. The following command copies it to the correct location, sets the permissions correctly and installs it:

root@towel:/home/alertr/sensorClientRaspberryPi/init.d_example# cp alertRsensorRaspberryPi.sh /etc/init.d/

root@towel:/etc/init.d# chown root:root alertRsensorRaspberryPi.sh
root@towel:/etc/init.d# chmod 755 alertRsensorRaspberryPi.sh

root@towel:/etc/init.d# update-rc.d alertRsensorRaspberryPi.sh defaults
 Adding system startup for /etc/init.d/alertRsensorRaspberryPi.sh ...
   /etc/rc0.d/K20alertRsensorRaspberryPi.sh -> ../init.d/alertRsensorRaspberryPi.sh
   /etc/rc1.d/K20alertRsensorRaspberryPi.sh -> ../init.d/alertRsensorRaspberryPi.sh
   /etc/rc6.d/K20alertRsensorRaspberryPi.sh -> ../init.d/alertRsensorRaspberryPi.sh
   /etc/rc2.d/S20alertRsensorRaspberryPi.sh -> ../init.d/alertRsensorRaspberryPi.sh
   /etc/rc3.d/S20alertRsensorRaspberryPi.sh -> ../init.d/alertRsensorRaspberryPi.sh
   /etc/rc4.d/S20alertRsensorRaspberryPi.sh -> ../init.d/alertRsensorRaspberryPi.sh
   /etc/rc5.d/S20alertRsensorRaspberryPi.sh -> ../init.d/alertRsensorRaspberryPi.sh

Next we have to configure the init.d script correctly. The following changes have to be made to the script:

[...]
# change USER to the user which runs the alertRclient
# NOTE: older versions of the Raspberry Pi packages need to be run as "root"
# in order to access the GPIO pins
USER=alertr
# change DAEMON to the path to run the alertRclient
DAEMON=/home/alertr/sensorClientRaspberryPi/alertRclient.py
[...]

In order to work correctly, the AlertR client has to be executable. With the following, we change the permissions of the AlertR client:

alertr@towel:~/sensorClientRaspberryPi$ chmod 755 alertRclient.py

To start the client as daemon, we can now execute:

root@towel:/home/alertr/sensorClientRaspberryPi# /etc/init.d/alertRsensorRaspberryPi.sh start

The log file of the client (it is created in the directory you have configured in the General Section) should now show the following:

[...]
07/27/2016 19:42:26 INFO: [alertRclient.py] Initializing sensors.
07/27/2016 19:42:27 INFO: [alertRclient.py] Connecting to server.
07/27/2016 19:42:28 INFO: [alertRclient.py] Starting watchdog thread.
07/27/2016 19:42:28 INFO: [alertRclient.py] Starting update check thread.
07/27/2016 19:42:28 INFO: [alertRclient.py] Client started.

Systemd

If your system uses systemd for its autostart, you have to configure the AlertR client a bit different. Copying the template and setting permissions is still the same:

root@towel:/home/alertr/sensorClientRaspberryPi/init.d_example# cp alertRsensorRaspberryPi.sh /etc/init.d/

root@towel:/etc/init.d# chown root:root alertRsensorRaspberryPi.sh
root@towel:/etc/init.d# chmod 755 alertRsensorRaspberryPi.sh

Configuring the init.d script correctly is also the same:

[...]
# change USER to the user which runs the alertRclient
# NOTE: older versions of the Raspberry Pi packages need to be run as "root"
# in order to access the GPIO pins
USER=alertr
# change DAEMON to the path to run the alertRclient
DAEMON=/home/alertr/sensorClientRaspberryPi/alertRclient.py
[...]

Now, systemd has to be configured. For this we copy the template service file to the correct location and install the service:

root@towel:/home/alertr/sensorClientRaspberryPi/init.d_example# cp alertRsensorRaspberryPi.service /etc/systemd/system/

root@towel:/home/alertr/sensorClientRaspberryPi# systemctl enable alertRsensorRaspberryPi.service

The alertR client can be started with the following command:

root@towel:/home/alertr/sensorClientRaspberryPi# service alertRsensorRaspberryPi.sh status

The log file of the client (it is created in the directory you have configured in the General Section) should now show the following:

[...]
07/27/2016 19:42:26 INFO: [alertRclient.py] Initializing sensors.
07/27/2016 19:42:27 INFO: [alertRclient.py] Connecting to server.
07/27/2016 19:42:28 INFO: [alertRclient.py] Starting watchdog thread.
07/27/2016 19:42:28 INFO: [alertRclient.py] Starting update check thread.
07/27/2016 19:42:28 INFO: [alertRclient.py] Client started.

Troubleshooting

If you experience problems, please check the log file first. If it is not helpful, change the log level to DEBUG and check again. If no error can be seen, please start the AlertR client manually and check if an error occurs that is not printed into the log file. This can be done by just executing the AlertR client as the user that it normally runs with.

alertr@towel:~/sensorClientRaspberryPi$ ./alertRclient.py

If you still have problems and do not know how to solve them, you can ask on the community page on reddit or you can use the Github Issues.

Clone this wiki locally