Skip to content

Data table backend for dplyr

License

Unknown, MIT licenses found

Licenses found

Unknown
LICENSE
MIT
LICENSE.md
Notifications You must be signed in to change notification settings

tidyverse/dtplyr

Repository files navigation

dtplyr

CRAN status R-CMD-check Codecov test coverage

Overview

data.table seal of approvaldtplyr provides a data.table backend for dplyr. The goal of dtplyr is to allow you to write dplyr code that is automatically translated to the equivalent, but usually much faster, data.table code.

See vignette("translation") for details of the current translations, and table.express and rqdatatable for related work.

Installation

You can install from CRAN with:

install.packages("dtplyr")

Or try the development version from GitHub with:

# install.packages("pak")
pak::pak("tidyverse/dtplyr")

Usage

To use dtplyr, you must at least load dtplyr and dplyr. You may also want to load data.table so you can access the other goodies that it provides:

library(data.table)
#> Warning: package 'data.table' was built under R version 4.4.1
library(dtplyr)
library(dplyr, warn.conflicts = FALSE)

Then use lazy_dt() to create a “lazy” data table that tracks the operations performed on it.

mtcars2 <- lazy_dt(mtcars)

You can preview the transformation (including the generated data.table code) by printing the result:

mtcars2 %>%
  filter(wt < 5) %>%
  mutate(l100k = 235.21 / mpg) %>% # liters / 100 km
  group_by(cyl) %>%
  summarise(l100k = mean(l100k))
#> Source: local data table [3 x 2]
#> Call:   `_DT1`[wt < 5][, `:=`(l100k = 235.21/mpg)][, .(l100k = mean(l100k)), 
#>     keyby = .(cyl)]
#> 
#>     cyl l100k
#>   <dbl> <dbl>
#> 1     4  9.05
#> 2     6 12.0 
#> 3     8 14.9 
#> 
#> # Use as.data.table()/as.data.frame()/as_tibble() to access results

But generally you should reserve this only for debugging, and use as.data.table(), as.data.frame(), or as_tibble() to indicate that you’re done with the transformation and want to access the results:

mtcars2 %>%
  filter(wt < 5) %>%
  mutate(l100k = 235.21 / mpg) %>% # liters / 100 km
  group_by(cyl) %>%
  summarise(l100k = mean(l100k)) %>%
  as_tibble()
#> # A tibble: 3 × 2
#>     cyl l100k
#>   <dbl> <dbl>
#> 1     4  9.05
#> 2     6 12.0 
#> 3     8 14.9

Why is dtplyr slower than data.table?

There are two primary reasons that dtplyr will always be somewhat slower than data.table:

  • Each dplyr verb must do some work to convert dplyr syntax to data.table syntax. This takes time proportional to the complexity of the input code, not the input data, so should be a negligible overhead for large datasets. Initial benchmarks suggest that the overhead should be under 1ms per dplyr call.

  • To match dplyr semantics, mutate() does not modify in place by default. This means that most expressions involving mutate() must make a copy that would not be necessary if you were using data.table directly. (You can opt out of this behaviour in lazy_dt() with immutable = FALSE).

Code of Conduct

Please note that the dtplyr project is released with a Contributor Code of Conduct. By contributing to this project, you agree to abide by its terms.