Board: Samr21 xpro
The SAMR21 Xplained Pro is a compact evaluation board by Atmel featuring a ATSAMR21G18A SoC. The SoC includes a SAMD21 ARM Cortex-M0+ micro-controller bundled with Atmel's AT86RF233, a 2.4GHz IEEE802.15.4 compatible radio. For programming the MCU comes with 32Kb of RAM and 256Kb of flash memory.
The samr21-xpro is available from various hardware vendors for ~40EUR (as of sep. 2014).
| MCU | ATSAMR21G18A |
|---|---|
| Family | ARM Cortex-M0+ |
| Vendor | Atmel |
| RAM | 32Kb |
| Flash | 256Kb |
| Frequency | up to 48MHz |
| FPU | no |
| Timers | 6 (1x 16-bit, 2x 24-bit, 3x 32-bit) |
| ADCs | 1x 12-bit (8 channels) |
| UARTs | max 5 (shared with SPI and I2C) |
| SPIs | max 5 (see UART) |
| I2Cs | max 5 (see UART) |
| Vcc | 1.8V - 3.6V |
| Datasheet | Datasheet |
| Board Manual | Board Manual |
1 User button and 1 LED:
| Device | PIN |
|---|---|
| LED0 | PA19 |
| SW0 (button) | PA28 |
The SAMR21 SoC includes an on-chip AT86RF233 radio. It is internally connected via SPI and some GPIO pins and behaves in exact the same way as externally connected SPI devices.
| Sensor | AT86RF233 |
|---|---|
| Type | 2.4GHz IEEE802.15.4 radio |
| Vendor | Atmel |
| Datasheet | See CPU datasheet |
| Connected to | SPI_0 |
| Pin Config: | |
| Device | SERCOM4 |
| MOSI | PB30 (OUT, SPI mosi) |
| MISO | PC19 (IN, SPI miso) |
| SCLK | PC18 (OUT, SPI sclk) |
| CS | PB31 (OUT, GPIO output) |
| IRQ | PB00 (IN, GPIO external interrupt) |
| RSTN | PB15 (OUT, GPIO output) |
| SLP_TR | PA20 (OUT, GPIO output) |
Please refer to this tracker to see which projects are work in progress and who is the contact person for this.
| Device | ID | Supported | Comments |
|---|---|---|---|
| MCU | samd21 | partly | Energy saving modes not fully utilized |
| Low-level driver | GPIO | yes | |
| PWM | no | ||
| UART | partly | only one UART by now | |
| I2C | yes | ||
| SPI | yes | ||
| USB | no | ||
| RTT | no | in progress | |
| RTC | yes | ||
| RNG | no | no HW module | |
| Timer | yes | ||
| Radio Chip | AT86RF233 | yes | using at86rf231 driver (this will be renamed to at86rf2xx) |
Connect the device to your Micro-USB cable using the port labeled as EDBG.
The standard method for flashing RIOT to the samr21-xpro is using OpenOCD. For this to work properly, you have to make sure to use a very recent version of OpenOCD. The v0.8.0 release will not work. If this is still the current release you'll have to build OpenOCD from source.
Refer to https://github.com/RIOT-OS/RIOT/wiki/OpenOCD for building OpenOCD and make sure "cmsis-dap" and "hidapi-libusb" are enabled.
On Linux you will have to add a udev rule for hidraw, like
KERNEL=="hidraw*", SUBSYSTEM=="hidraw", MODE="0664", GROUP="plugdev"
With yaourt:
yaourt -S hidapi-git
yaourt -S openocd-git
# edit PKGBUILD, add "cmsis-dap hidapi-libusb" to "_features"
See http://watr.li/samr21-dev-setup-ubuntu.html
For using the samr21-xpro board we strongly recommend the usage of the GNU Tools for ARM Embedded Processors toolchain.
When connecting an I2C device and a logic analyzer to an I2C port at the same time, the internal pull-up resistors are not sufficient for stable bus operation. You probably have to connect external pull-ups to both bus lines. 10K is a good value to start with.
The default stack sizes have not been tuned properly yet. If in doubt why your application crashes try increasing the default stack sizes and use ps to find out how much stack is being used.
Tracked in https://github.com/RIOT-OS/RIOT/issues/2228
When using the SW0 user button as interrupt source it appers that this is triggered when just tipping on the button and not really pressing it.
There is a diff of one and a half minutes every hour. Tracked in https://github.com/RIOT-OS/RIOT/issues/2261