# This is a combination of 18 commits.

# This is the 1st commit message:

Add Support for ADIMLab Granty

# The commit message #2 will be skipped:

# Update Configuration.h

# The commit message #3 will be skipped:

# Add files via upload
#
# Add Support for ADIMLab Granty

# The commit message #4 will be skipped:

# Create Configuration.h

# The commit message #5 will be skipped:

# Delete Configuration.h

# The commit message #6 will be skipped:

# Create Test.h

# The commit message #7 will be skipped:

# Add files via upload

# The commit message #8 will be skipped:

# Delete Test.h

# The commit message #9 will be skipped:

# Delete Configuration.h

# The commit message #10 will be skipped:

# Delete Configuration_adv.h

# The commit message #11 will be skipped:

# Add files via upload
#
# Add ADIMLab Pins

# The commit message #12 will be skipped:

# Add files via upload
#
# Add Bootscreen

# The commit message #13 will be skipped:

# Update Configuration.h
#
# Add Bootscreen

# The commit message #14 will be skipped:

# Update pins.h
#
# Add ADIMLab Board

# The commit message #15 will be skipped:

# Update boards.h
#
# Add ADIMLab Granty

# The commit message #16 will be skipped:

# Update Makefile
#
# Add ADIMLab Granty

# The commit message #17 will be skipped:

# Update boards.h

# The commit message #18 will be skipped:

# Update Makefile

Marlin/Makefile

@@ -251,6 +251,8 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1141)
 else ifeq ($(HARDWARE_MOTHERBOARD),1142)
 # Overlord/Overlord Pro
 else ifeq ($(HARDWARE_MOTHERBOARD),1143)
+# ADIMLab Granty
+else ifeq ($(HARDWARE_MOTHERBOARD),1144)
 
 #
 # RAMBo and derivatives

Marlin/src/core/boards.h

@@ -95,6 +95,7 @@
 #define BOARD_Z_BOLT_X_SERIES         1141  // Z-Bolt X Series
 #define BOARD_TT_OSCAR                1142  // TT OSCAR
 #define BOARD_OVERLORD                1143  // Overlord/Overlord Pro
+#define BOARD_HJC2560C_REV2           1144  // ADIMLab Granty
 
 //
 // RAMBo and derivatives

Marlin/src/pins/mega/pins_HJC2560C_REV2.h

@@ -0,0 +1,193 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * HJC2560-C Rev2.x pin assignments
+ */
+
+/**
+ * Rev 2.x   2 Aug 2018
+ */
+
+#ifndef __AVR_ATmega2560__
+  #error "Oops!  Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
+#endif
+
+// BOARD Info
+#define DEFAULT_MACHINE_NAME    "HCMaker7"
+#define BOARD_NAME              "HJC2560-C"
+#define BOARD_REV               "Rev: 2.1"        //主板版本：Rev 2.1, Rs=0.05R
+#define R_SENSOR                "R-sensor: R050"             //检测电阻
+
+// FIRMWARE Info
+#define FIRMWARE_NAME           "Marlin 1-1-9"           
+#define FIRMWARE_REV            "Rev: 1.4"        //固件版本：Rev 1.4
+
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN         22
+#define Y_STOP_PIN         26
+#define Z_STOP_PIN         29
+#define EXP_STOP_PIN       28
+
+//
+// Steppers
+//
+#define X_STEP_PIN         25
+#define X_DIR_PIN          23
+#define X_ENABLE_PIN       27
+
+#define Y_STEP_PIN         32
+#define Y_DIR_PIN          33
+#define Y_ENABLE_PIN       31
+
+#define Z_STEP_PIN         35
+#define Z_DIR_PIN          36
+#define Z_ENABLE_PIN       34
+
+#define E0_STEP_PIN        42
+#define E0_DIR_PIN         43
+#define E0_ENABLE_PIN      37
+
+#define E1_STEP_PIN        49
+#define E1_DIR_PIN         47
+#define E1_ENABLE_PIN      48
+
+#define MOTOR_CURRENT_PWM_XY_PIN   44
+#define MOTOR_CURRENT_PWM_Z_PIN    45
+#define MOTOR_CURRENT_PWM_E_PIN    46
+// Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range
+#ifndef MOTOR_CURRENT_PWM_RANGE
+  #define MOTOR_CURRENT_PWM_RANGE  2000
+#endif
+#define DEFAULT_PWM_MOTOR_CURRENT  {1300, 1300, 1250}
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN          8   // Analog Input
+#define TEMP_1_PIN          9   // Analog Input
+#define TEMP_BED_PIN       10   // Analog Input
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN        2
+#define HEATER_1_PIN        3
+#define HEATER_BED_PIN      4
+
+//#ifndef FAN_PIN
+  #define FAN_PIN           7  //默认不使用PWM_FAN冷却喷嘴，如果需要，则取消注释
+//#endif
+
+//
+// Misc. Functions
+//
+#define SDSS               53
+#define SD_DETECT_PIN      39
+//#define LED_PIN           8           
+#define CASE_LIGHT_PIN      8           //8 默认挤出机风扇作为Case LED，如果需要PWM FAN,则需要将FAN_PIN置为7，LED_PIN置为8
+//#define SAFETY_TRIGGERED_PIN     28   // PIN to detect the safety circuit has triggered
+//#define MAIN_VOLTAGE_MEASURE_PIN 14   // ANALOG PIN to measure the main voltage, with a 100k - 4k7 resitor divider.
+
+//
+// LCD / Controller
+//
+#if ENABLED(ULTRA_LCD)
+
+  #define BEEPER_PIN 18
+
+  #if ENABLED(NEWPANEL)
+
+  	#if ENABLED(HJC_LCD_SMART_CONTROLLER)
+   		 #define LCD_PINS_RS    		20		//LCD_CS
+    	 #define LCD_PINS_ENABLE 		15		//LCD_SDA
+    	 #define LCD_PINS_D4    		14		//LCD_SCK
+		   #define LCD_BACKLIGHT_PIN 	    5    	//LCD_Backlight
+//         #ifndef LCD_CONTRAST_PIN
+//         	#define LCD_CONTRAST_PIN    5    //LCD_Contrast
+//         #endif
+		    // define digital pin 24 for the filament runout sensor. 
+		  #ifndef FIL_RUNOUT_PIN
+		 	  #define FIL_RUNOUT_PIN   	24		//Filament runout 
+      #endif
+	  #else
+    	#define LCD_PINS_RS    			20		//LCD_CS
+   		#define LCD_PINS_ENABLE 		15		//LCD_SDA
+   		#define LCD_PINS_D4    			14		//LCD_SCK
+      #define LCD_PINS_D5    			21		
+   		#define LCD_PINS_D6     		5
+   		#define LCD_PINS_D7     		6
+    #endif
+
+   	// buttons are directly attached
+   	#define BTN_EN1 41
+   	#define BTN_EN2 40
+   	#define BTN_ENC 19
+
+    #define SD_DETECT_PIN 		39
+
+  #else // !NEWPANEL - Old style panel with shift register
+
+    // buttons are attached to a shift register
+    #define SHIFT_CLK 		  	38
+    #define SHIFT_LD 		    	42
+    #define SHIFT_OUT 		  	40
+    #define SHIFT_EN 		    	17
+
+    #define LCD_PINS_RS 		  16
+    #define LCD_PINS_ENABLE 	5
+    #define LCD_PINS_D4 	  	6
+    #define LCD_PINS_D5 	  	21
+    #define LCD_PINS_D6 	  	20
+    #define LCD_PINS_D7 	  	19
+
+    #define SD_DETECT_PIN      -1
+
+  #endif // !NEWPANEL
+
+#endif // ULTRA_LCD
+
+
+//
+// M3/M4/M5 - Spindle/Laser Control，默认，主轴/激光器使用独立的PWM引脚(D9)控制
+// 如果使用了PWM_FAN,Case_Light和Spindle/Laser,  并希望Spindle/Laser使用CASE_Light的线，则将
+//SPINDLE_LASER_PWM_PIN 定义为8
+//
+#if ENABLED(SPINDLE_LASER_ENABLE)   // use the LED_PIN for spindle speed control or case light
+//  #undef LED_PIN
+  #define SPINDLE_DIR_PIN           16
+  #define SPINDLE_LASER_ENABLE_PIN  17   // Pin should have a pullup!
+  #define SPINDLE_LASER_PWM_PIN     9   // MUST BE HARDWARE PWM，
+//#else
+//  #undef LED_PIN
+//  #define CASE_LIGHT_PIN            7
+#endif
+
+//
+// Servos
+//
+//#ifndef SERVO0_PIN
+//  #define SERVO0_PIN       11
+//#endif

Marlin/src/pins/pins.h

@@ -236,6 +236,8 @@
   #include "mega/pins_WANHAO_ONEPLUS.h"         // ATmega2560                             env:megaatmega2560
 #elif MB(OVERLORD)
   #include "mega/pins_OVERLORD.h"               // ATmega2560                             env:megaatmega2560
+#elif MB(HJC2560C_REV2)
+  #include "mega/pins_HJC2560C_REV2.h"          // ATmega2560                             env:megaatmega2560
 
 //
 // ATmega1281, ATmega2561