RFE: add genfscon support for regex paths #29
Labels
Comments
|
Android init does the equivalent of a restorecon -R /sys on boot, so all sysfs entries can be labeled based on file_contexts, which supports regexes; this required some careful optimization to minimize boot time, which has been ported upstream into libselinux selinux_restorecon() used by newer policycoreutils restorecon (2.6 and later). Linux distributions have to date chosen to only label specific /sys entries via systemd tmpfiles.d (e.g. see /usr/lib/tmpfiles.d/selinux-policy.conf in Fedora), which likewise will be based on file_contexts; you should be able to use the Z option (notice capitalization) to recursively relabel a directory tree. |
pcmoore
pushed a commit
that referenced
this issue
May 17, 2017
Dmitry reported a lockdep splat [1] (false positive) that we can fix by releasing the spinlock before calling icmp_send() from ip_expire() This is a false positive because sending an ICMP message can not possibly re-enter the IP frag engine. [1] [ INFO: possible circular locking dependency detected ] 4.10.0+ #29 Not tainted ------------------------------------------------------- modprobe/12392 is trying to acquire lock: (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] spin_lock include/linux/spinlock.h:299 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] __netif_tx_lock include/linux/netdevice.h:3486 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 but task is already holding lock: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&(&q->lock)->rlock){+.-...}: validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] ip_defrag+0x3a2/0x4130 net/ipv4/ip_fragment.c:669 ip_check_defrag+0x4e3/0x8b0 net/ipv4/ip_fragment.c:713 packet_rcv_fanout+0x282/0x800 net/packet/af_packet.c:1459 deliver_skb net/core/dev.c:1834 [inline] dev_queue_xmit_nit+0x294/0xa90 net/core/dev.c:1890 xmit_one net/core/dev.c:2903 [inline] dev_hard_start_xmit+0x16b/0xab0 net/core/dev.c:2923 sch_direct_xmit+0x31f/0x6d0 net/sched/sch_generic.c:182 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_resolve_output+0x6b9/0xb10 net/core/neighbour.c:1308 neigh_output include/net/neighbour.h:478 [inline] ip_finish_output2+0x8b8/0x15a0 net/ipv4/ip_output.c:228 ip_do_fragment+0x1d93/0x2720 net/ipv4/ip_output.c:672 ip_fragment.constprop.54+0x145/0x200 net/ipv4/ip_output.c:545 ip_finish_output+0x82d/0xe10 net/ipv4/ip_output.c:314 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 raw_sendmsg+0x26de/0x3a00 net/ipv4/raw.c:655 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 ___sys_sendmsg+0x4a3/0x9f0 net/socket.c:1985 __sys_sendmmsg+0x25c/0x750 net/socket.c:2075 SYSC_sendmmsg net/socket.c:2106 [inline] SyS_sendmmsg+0x35/0x60 net/socket.c:2101 do_syscall_64+0x2e8/0x930 arch/x86/entry/common.c:281 return_from_SYSCALL_64+0x0/0x7a -> #0 (_xmit_ETHER#2){+.-...}: check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 __read_once_size include/linux/compiler.h:254 [inline] atomic_read arch/x86/include/asm/atomic.h:26 [inline] rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] __rcu_is_watching kernel/rcu/tree.c:1133 [inline] rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); *** DEADLOCK *** 10 locks held by modprobe/12392: #0: (&mm->mmap_sem){++++++}, at: [<ffffffff81329758>] __do_page_fault+0x2b8/0xb60 arch/x86/mm/fault.c:1336 #1: (rcu_read_lock){......}, at: [<ffffffff8188cab6>] filemap_map_pages+0x1e6/0x1570 mm/filemap.c:2324 #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] spin_lock include/linux/spinlock.h:299 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] pte_alloc_one_map mm/memory.c:2944 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] alloc_set_pte+0x13b8/0x1b90 mm/memory.c:3072 #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] lockdep_copy_map include/linux/lockdep.h:175 [inline] #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] call_timer_fn+0x1c2/0x820 kernel/time/timer.c:1258 #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 #5: (rcu_read_lock){......}, at: [<ffffffff8389a633>] ip_expire+0x1b3/0x6c0 net/ipv4/ip_fragment.c:216 #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] spin_trylock include/linux/spinlock.h:309 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_xmit_lock net/ipv4/icmp.c:219 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_send+0x803/0x1c80 net/ipv4/icmp.c:681 #7: (rcu_read_lock_bh){......}, at: [<ffffffff838ab9a1>] ip_finish_output2+0x2c1/0x15a0 net/ipv4/ip_output.c:198 #8: (rcu_read_lock_bh){......}, at: [<ffffffff836d1dee>] __dev_queue_xmit+0x23e/0x1e60 net/core/dev.c:3324 #9: (dev->qdisc_running_key ?: &qdisc_running_key){+.....}, at: [<ffffffff836d3a27>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 stack backtrace: CPU: 0 PID: 12392 Comm: modprobe Not tainted 4.10.0+ #29 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x2ee/0x3ef lib/dump_stack.c:52 print_circular_bug+0x307/0x3b0 kernel/locking/lockdep.c:1204 check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 RIP: 0010:__read_once_size include/linux/compiler.h:254 [inline] RIP: 0010:atomic_read arch/x86/include/asm/atomic.h:26 [inline] RIP: 0010:rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] RIP: 0010:__rcu_is_watching kernel/rcu/tree.c:1133 [inline] RIP: 0010:rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 RSP: 0000:ffff8801c391f120 EFLAGS: 00000a03 ORIG_RAX: ffffffffffffff10 RAX: dffffc0000000000 RBX: ffff8801c391f148 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 000055edd4374000 RDI: ffff8801dbe1ae0c RBP: ffff8801c391f1a0 R08: 0000000000000002 R09: 0000000000000000 R10: dffffc0000000000 R11: 0000000000000002 R12: 1ffff10038723e25 R13: ffff8801dbe1ae00 R14: ffff8801c391f680 R15: dffffc0000000000 </IRQ> rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 RIP: 0033:0x7f83172f2786 RSP: 002b:00007fffe859ae80 EFLAGS: 00010293 RAX: 000055edd4373040 RBX: 00007f83175111c8 RCX: 000055edd4373238 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007f8317510970 RBP: 00007fffe859afd0 R08: 0000000000000009 R09: 0000000000000000 R10: 0000000000000064 R11: 0000000000000000 R12: 000055edd4373040 R13: 0000000000000000 R14: 00007fffe859afe8 R15: 0000000000000000 Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stephensmalley
pushed a commit
to stephensmalley/selinux-kernel
that referenced
this issue
Apr 17, 2018
Patch series "optimize memory hotplug", v3.
This patchset:
- Improves hotplug performance by eliminating a number of struct page
traverses during memory hotplug.
- Fixes some issues with hotplugging, where boundaries were not
properly checked. And on x86 block size was not properly aligned with
end of memory
- Also, potentially improves boot performance by eliminating condition
from __init_single_page().
- Adds robustness by verifying that that struct pages are correctly
poisoned when flags are accessed.
The following experiments were performed on Xeon(R) CPU E7-8895 v3 @
2.60GHz with 1T RAM:
booting in qemu with 960G of memory, time to initialize struct pages:
no-kvm:
TRY1 TRY2
BEFORE: 39.433668 39.39705
AFTER: 36.903781 36.989329
with-kvm:
BEFORE: 10.977447 11.103164
AFTER: 10.929072 10.751885
Hotplug 896G memory:
no-kvm:
TRY1 TRY2
BEFORE: 848.740000 846.910000
AFTER: 783.070000 786.560000
with-kvm:
TRY1 TRY2
BEFORE: 34.410000 33.57
AFTER: 29.810000 29.580000
This patch (of 6):
Start qemu with the following arguments:
-m 64G,slots=2,maxmem=66G -object memory-backend-ram,id=mem1,size=2G
Which: boots machine with 64G, and adds a device mem1 with 2G which can
be hotplugged later.
Also make sure that config has the following turned on:
CONFIG_MEMORY_HOTPLUG
CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE
CONFIG_ACPI_HOTPLUG_MEMORY
Using the qemu monitor hotplug the memory (make sure config has (qemu)
device_add pc-dimm,id=dimm1,memdev=mem1
The operation will fail with the following trace:
WARNING: CPU: 0 PID: 91 at drivers/base/memory.c:205
pages_correctly_reserved+0xe6/0x110
Modules linked in:
CPU: 0 PID: 91 Comm: systemd-udevd Not tainted 4.16.0-rc1_pt_master SELinuxProject#29
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:pages_correctly_reserved+0xe6/0x110
Call Trace:
memory_subsys_online+0x44/0xa0
device_online+0x51/0x80
store_mem_state+0x5e/0xe0
kernfs_fop_write+0xfa/0x170
__vfs_write+0x2e/0x150
vfs_write+0xa8/0x1a0
SyS_write+0x4d/0xb0
do_syscall_64+0x5d/0x110
entry_SYSCALL_64_after_hwframe+0x21/0x86
---[ end trace 6203bc4f1a5d30e8 ]---
The problem is detected in: drivers/base/memory.c
static bool pages_correctly_reserved(unsigned long start_pfn)
205 if (WARN_ON_ONCE(!pfn_valid(pfn)))
This function loops through every section in the newly added memory
block and verifies that the first pfn is valid, meaning section exists,
has mapping (struct page array), and is online.
The block size on x86 is usually 128M, but when machine is booted with
more than 64G of memory, the block size is changed to 2G: $ cat
/sys/devices/system/memory/block_size_bytes 80000000
or
$ dmesg | grep "block size"
[ 0.086469] x86/mm: Memory block size: 2048MB
During memory hotplug, and hotremove we verify that the range is section
size aligned, but we actually must verify that it is block size aligned,
because that is the proper unit for hotplug operations. See:
Documentation/memory-hotplug.txt
So, when the start_pfn of newly added memory is not block size aligned,
we can get a memory block that has only part of it with properly
populated sections.
In our case the start_pfn starts from the last_pfn (end of physical
memory).
$ dmesg | grep last_pfn
[ 0.000000] e820: last_pfn = 0x1040000 max_arch_pfn = 0x400000000
0x1040000 == 65G, and so is not 2G aligned!
The fix is to enforce that memory that is hotplugged and hotremoved is
block size aligned.
With this fix, running the above sequence yield to the following result:
(qemu) device_add pc-dimm,id=dimm1,memdev=mem1
Block size [0x80000000] unaligned hotplug range: start 0x1040000000,
size 0x80000000
acpi PNP0C80:00: add_memory failed
acpi PNP0C80:00: acpi_memory_enable_device() error
acpi PNP0C80:00: Enumeration failure
Link: http://lkml.kernel.org/r/20180213193159.14606-2-pasha.tatashin@oracle.com
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pcmoore
pushed a commit
that referenced
this issue
May 3, 2022
Reported by checkpatch:
security/selinux/nlmsgtab.c
---------------------------
ERROR: that open brace { should be on the previous line
#29: FILE: security/selinux/nlmsgtab.c:29:
+static const struct nlmsg_perm nlmsg_route_perms[] =
+{
ERROR: that open brace { should be on the previous line
#97: FILE: security/selinux/nlmsgtab.c:97:
+static const struct nlmsg_perm nlmsg_tcpdiag_perms[] =
+{
ERROR: that open brace { should be on the previous line
#105: FILE: security/selinux/nlmsgtab.c:105:
+static const struct nlmsg_perm nlmsg_xfrm_perms[] =
+{
ERROR: that open brace { should be on the previous line
#134: FILE: security/selinux/nlmsgtab.c:134:
+static const struct nlmsg_perm nlmsg_audit_perms[] =
+{
security/selinux/ss/policydb.c
------------------------------
ERROR: that open brace { should be on the previous line
#318: FILE: security/selinux/ss/policydb.c:318:
+static int (*destroy_f[SYM_NUM]) (void *key, void *datum, void *datap) =
+{
ERROR: that open brace { should be on the previous line
#674: FILE: security/selinux/ss/policydb.c:674:
+static int (*index_f[SYM_NUM]) (void *key, void *datum, void *datap) =
+{
ERROR: that open brace { should be on the previous line
#1643: FILE: security/selinux/ss/policydb.c:1643:
+static int (*read_f[SYM_NUM]) (struct policydb *p, struct symtab *s, void *fp) =
+{
ERROR: that open brace { should be on the previous line
#3246: FILE: security/selinux/ss/policydb.c:3246:
+ void *datap) =
+{
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
pcmoore
pushed a commit
that referenced
this issue
Jun 16, 2022
This commit adds python script to parse CoreSight tracing event and
print out source line and disassembly, it generates readable program
execution flow for easier humans inspecting.
The script receives CoreSight tracing packet with below format:
+------------+------------+------------+
packet(n): | addr | ip | cpu |
+------------+------------+------------+
packet(n+1): | addr | ip | cpu |
+------------+------------+------------+
packet::addr presents the start address of the coming branch sample, and
packet::ip is the last address of the branch smple. Therefore, a code
section between branches starts from packet(n)::addr and it stops at
packet(n+1)::ip. As results we combines the two continuous packets to
generate the address range for instructions:
[ sample(n)::addr .. sample(n+1)::ip ]
The script supports both objdump or llvm-objdump for disassembly with
specifying option '-d'. If doesn't specify option '-d', the script
simply outputs source lines and symbols.
Below shows usages with llvm-objdump or objdump to output disassembly.
# perf script -s scripts/python/arm-cs-trace-disasm.py -- -d llvm-objdump-11 -k ./vmlinux
ARM CoreSight Trace Data Assembler Dump
ffff800008eb3198 <etm4_enable_hw>:
ffff800008eb3310: c0 38 00 35 cbnz w0, 0xffff800008eb3a28 <etm4_enable_hw+0x890>
ffff800008eb3314: 9f 3f 03 d5 dsb sy
ffff800008eb3318: df 3f 03 d5 isb
ffff800008eb331c: f5 5b 42 a9 ldp x21, x22, [sp, #32]
ffff800008eb3320: fb 73 45 a9 ldp x27, x28, [sp, #80]
ffff800008eb3324: e0 82 40 39 ldrb w0, [x23, #32]
ffff800008eb3328: 60 00 00 34 cbz w0, 0xffff800008eb3334 <etm4_enable_hw+0x19c>
ffff800008eb332c: e0 03 19 aa mov x0, x25
ffff800008eb3330: 8c fe ff 97 bl 0xffff800008eb2d60 <etm4_cs_lock.isra.0.part.0>
main 6728/6728 [0004] 0.000000000 etm4_enable_hw+0x198 [kernel.kallsyms]
ffff800008eb2d60 <etm4_cs_lock.isra.0.part.0>:
ffff800008eb2d60: 1f 20 03 d5 nop
ffff800008eb2d64: 1f 20 03 d5 nop
ffff800008eb2d68: 3f 23 03 d5 hint #25
ffff800008eb2d6c: 00 00 40 f9 ldr x0, [x0]
ffff800008eb2d70: 9f 3f 03 d5 dsb sy
ffff800008eb2d74: 00 c0 3e 91 add x0, x0, #4016
ffff800008eb2d78: 1f 00 00 b9 str wzr, [x0]
ffff800008eb2d7c: bf 23 03 d5 hint #29
ffff800008eb2d80: c0 03 5f d6 ret
main 6728/6728 [0004] 0.000000000 etm4_cs_lock.isra.0.part.0+0x20
# perf script -s scripts/python/arm-cs-trace-disasm.py -- -d objdump -k ./vmlinux
ARM CoreSight Trace Data Assembler Dump
ffff800008eb3310 <etm4_enable_hw+0x178>:
ffff800008eb3310: 350038c0 cbnz w0, ffff800008eb3a28 <etm4_enable_hw+0x890>
ffff800008eb3314: d5033f9f dsb sy
ffff800008eb3318: d5033fdf isb
ffff800008eb331c: a9425bf5 ldp x21, x22, [sp, #32]
ffff800008eb3320: a94573fb ldp x27, x28, [sp, #80]
ffff800008eb3324: 394082e0 ldrb w0, [x23, #32]
ffff800008eb3328: 34000060 cbz w0, ffff800008eb3334 <etm4_enable_hw+0x19c>
ffff800008eb332c: aa1903e0 mov x0, x25
ffff800008eb3330: 97fffe8c bl ffff800008eb2d60 <etm4_cs_lock.isra.0.part.0>
main 6728/6728 [0004] 0.000000000 etm4_enable_hw+0x198 [kernel.kallsyms]
ffff800008eb2d60 <etm4_cs_lock.isra.0.part.0>:
ffff800008eb2d60: d503201f nop
ffff800008eb2d64: d503201f nop
ffff800008eb2d68: d503233f paciasp
ffff800008eb2d6c: f9400000 ldr x0, [x0]
ffff800008eb2d70: d5033f9f dsb sy
ffff800008eb2d74: 913ec000 add x0, x0, #0xfb0
ffff800008eb2d78: b900001f str wzr, [x0]
ffff800008eb2d7c: d50323bf autiasp
ffff800008eb2d80: d65f03c0 ret
main 6728/6728 [0004] 0.000000000 etm4_cs_lock.isra.0.part.0+0x20
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Co-authored-by: Al Grant <al.grant@arm.com>
Co-authored-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Co-authored-by: Tor Jeremiassen <tor@ti.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Eelco Chaudron <echaudro@redhat.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Tanmay Jagdale <tanmay@marvell.com>
Cc: coresight@lists.linaro.org
Cc: zengshun . wu <zengshun.wu@outlook.com>
Link: https://lore.kernel.org/r/20220521130446.4163597-3-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
stephensmalley
pushed a commit
to stephensmalley/selinux-kernel
that referenced
this issue
May 2, 2024
As previously explained, the rehash delayed work migrates filters from one region to another. This is done by iterating over all chunks (all the filters with the same priority) in the region and in each chunk iterating over all the filters. When the work runs out of credits it stores the current chunk and entry as markers in the per-work context so that it would know where to resume the migration from the next time the work is scheduled. Upon error, the chunk marker is reset to NULL, but without resetting the entry markers despite being relative to it. This can result in migration being resumed from an entry that does not belong to the chunk being migrated. In turn, this will eventually lead to a chunk being iterated over as if it is an entry. Because of how the two structures happen to be defined, this does not lead to KASAN splats, but to warnings such as [1]. Fix by creating a helper that resets all the markers and call it from all the places the currently only reset the chunk marker. For good measures also call it when starting a completely new rehash. Add a warning to avoid future cases. [1] WARNING: CPU: 7 PID: 1076 at drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:407 mlxsw_afk_encode+0x242/0x2f0 Modules linked in: CPU: 7 PID: 1076 Comm: kworker/7:24 Tainted: G W 6.9.0-rc3-custom-00880-g29e61d91b77b SELinuxProject#29 Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:mlxsw_afk_encode+0x242/0x2f0 [...] Call Trace: <TASK> mlxsw_sp_acl_atcam_entry_add+0xd9/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x109/0x290 mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x470 process_one_work+0x151/0x370 worker_thread+0x2cb/0x3e0 kthread+0xd0/0x100 ret_from_fork+0x34/0x50 </TASK> Fixes: 6f9579d ("mlxsw: spectrum_acl: Remember where to continue rehash migration") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Alexander Zubkov <green@qrator.net> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/cc17eed86b41dd829d39b07906fec074a9ce580e.1713797103.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pcmoore
pushed a commit
that referenced
this issue
May 28, 2024
Reinitialize the whole EST structure would also reset the mutex lock which is embedded in the EST structure, and then trigger the following warning. To address this, move the lock to struct stmmac_priv. We also need to reacquire the mutex lock when doing this initialization. DEBUG_LOCKS_WARN_ON(lock->magic != lock) WARNING: CPU: 3 PID: 505 at kernel/locking/mutex.c:587 __mutex_lock+0xd84/0x1068 Modules linked in: CPU: 3 PID: 505 Comm: tc Not tainted 6.9.0-rc6-00053-g0106679839f7-dirty #29 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __mutex_lock+0xd84/0x1068 lr : __mutex_lock+0xd84/0x1068 sp : ffffffc0864e3570 x29: ffffffc0864e3570 x28: ffffffc0817bdc78 x27: 0000000000000003 x26: ffffff80c54f1808 x25: ffffff80c9164080 x24: ffffffc080d723ac x23: 0000000000000000 x22: 0000000000000002 x21: 0000000000000000 x20: 0000000000000000 x19: ffffffc083bc3000 x18: ffffffffffffffff x17: ffffffc08117b080 x16: 0000000000000002 x15: ffffff80d2d40000 x14: 00000000000002da x13: ffffff80d2d404b8 x12: ffffffc082b5a5c8 x11: ffffffc082bca680 x10: ffffffc082bb2640 x9 : ffffffc082bb2698 x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001 x5 : ffffff8178fe0d48 x4 : 0000000000000000 x3 : 0000000000000027 x2 : ffffff8178fe0d50 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: __mutex_lock+0xd84/0x1068 mutex_lock_nested+0x28/0x34 tc_setup_taprio+0x118/0x68c stmmac_setup_tc+0x50/0xf0 taprio_change+0x868/0xc9c Fixes: b2aae65 ("net: stmmac: add mutex lock to protect est parameters") Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20240513014346.1718740-2-xiaolei.wang@windriver.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Currently one could not further restrict the access to the kernel pseudo filesystem sysfs.
Paths like
/sys/bus/usb/devices/or/sys/class/net/eth0could be labeled, but these files are symlinks to hardware dependent files, e.g./sys/class/net/eth0 -> ../../devices/pci0000:00/0000:00:1c.5/0000:05:00.0/net/eth0or/sys/bus/usb/devices/usb1 -> ../../../devices/pci0000:00/0000:00:1a.0/usb1.If genfscon would support regular expressions in the path argument one could label these files:
The text was updated successfully, but these errors were encountered: