arm:dts:mtjade: Enable I2C4 device access #3

thangqn-ampere · 2020-12-12T08:29:02Z

Set BMC_GPIOY2_I2C4_O_EN high to enable access to devices on the I2C4
bus.

Signed-off-by: Thang Q. Nguyen thang@os.amperecomputing.com

Set BMC_GPIOY2_I2C4_O_EN high to enable access to devices on the I2C4 bus. Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>

commit 2b12993 upstream. tl;dr: The Enhanced IBRS mitigation for Spectre v2 does not work as documented for RET instructions after VM exits. Mitigate it with a new one-entry RSB stuffing mechanism and a new LFENCE. == Background == Indirect Branch Restricted Speculation (IBRS) was designed to help mitigate Branch Target Injection and Speculative Store Bypass, i.e. Spectre, attacks. IBRS prevents software run in less privileged modes from affecting branch prediction in more privileged modes. IBRS requires the MSR to be written on every privilege level change. To overcome some of the performance issues of IBRS, Enhanced IBRS was introduced. eIBRS is an "always on" IBRS, in other words, just turn it on once instead of writing the MSR on every privilege level change. When eIBRS is enabled, more privileged modes should be protected from less privileged modes, including protecting VMMs from guests. == Problem == Here's a simplification of how guests are run on Linux' KVM: void run_kvm_guest(void) { // Prepare to run guest VMRESUME(); // Clean up after guest runs } The execution flow for that would look something like this to the processor: 1. Host-side: call run_kvm_guest() 2. Host-side: VMRESUME 3. Guest runs, does "CALL guest_function" 4. VM exit, host runs again 5. Host might make some "cleanup" function calls 6. Host-side: RET from run_kvm_guest() Now, when back on the host, there are a couple of possible scenarios of post-guest activity the host needs to do before executing host code: * on pre-eIBRS hardware (legacy IBRS, or nothing at all), the RSB is not touched and Linux has to do a 32-entry stuffing. * on eIBRS hardware, VM exit with IBRS enabled, or restoring the host IBRS=1 shortly after VM exit, has a documented side effect of flushing the RSB except in this PBRSB situation where the software needs to stuff the last RSB entry "by hand". IOW, with eIBRS supported, host RET instructions should no longer be influenced by guest behavior after the host retires a single CALL instruction. However, if the RET instructions are "unbalanced" with CALLs after a VM exit as is the RET in openbmc#6, it might speculatively use the address for the instruction after the CALL in #3 as an RSB prediction. This is a problem since the (untrusted) guest controls this address. Balanced CALL/RET instruction pairs such as in step openbmc#5 are not affected. == Solution == The PBRSB issue affects a wide variety of Intel processors which support eIBRS. But not all of them need mitigation. Today, X86_FEATURE_RSB_VMEXIT triggers an RSB filling sequence that mitigates PBRSB. Systems setting RSB_VMEXIT need no further mitigation - i.e., eIBRS systems which enable legacy IBRS explicitly. However, such systems (X86_FEATURE_IBRS_ENHANCED) do not set RSB_VMEXIT and most of them need a new mitigation. Therefore, introduce a new feature flag X86_FEATURE_RSB_VMEXIT_LITE which triggers a lighter-weight PBRSB mitigation versus RSB_VMEXIT. The lighter-weight mitigation performs a CALL instruction which is immediately followed by a speculative execution barrier (INT3). This steers speculative execution to the barrier -- just like a retpoline -- which ensures that speculation can never reach an unbalanced RET. Then, ensure this CALL is retired before continuing execution with an LFENCE. In other words, the window of exposure is opened at VM exit where RET behavior is troublesome. While the window is open, force RSB predictions sampling for RET targets to a dead end at the INT3. Close the window with the LFENCE. There is a subset of eIBRS systems which are not vulnerable to PBRSB. Add these systems to the cpu_vuln_whitelist[] as NO_EIBRS_PBRSB. Future systems that aren't vulnerable will set ARCH_CAP_PBRSB_NO. [ bp: Massage, incorporate review comments from Andy Cooper. ] Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Co-developed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 59c026c upstream. When use 'echo c > /proc/sysrq-trigger' to trigger kdump, riscv_crash_save_regs() will be called to save regs for vmcore, we found "epc" value 00ffffffa5537400 is not a valid kernel virtual address, but is a user virtual address. Other regs(eg, ra, sp, gp...) are correct kernel virtual address. Actually 0x00ffffffb0dd9400 is the user mode PC of 'PID: 113 Comm: sh', which is saved in the task's stack. [ 21.201701] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 openbmc#45 [ 21.201979] Hardware name: riscv-virtio,qemu (DT) [ 21.202160] epc : 00ffffffa5537400 ra : ffffffff80088640 sp : ff20000010333b90 [ 21.202435] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be7c [ 21.202707] t1 : 0720072007200720 t2 : 30203a7375746174 s0 : ff20000010333cf0 [ 21.202973] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 21.203243] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 28c8f0aeffea4e00 [ 21.203519] a5 : 28c8f0aeffea4e00 a6 : 0000000000000009 a7 : ffffffff8035c9b8 [ 21.203794] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 21.204062] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 21.204331] s8 : 00ffffffef451410 s9 : 0000000000000007 s10: 00aaaaaac0510700 [ 21.204606] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 21.204876] t5 : ff60000001218000 t6 : ff200000103338b8 [ 21.205079] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the incorrect PC, the backtrace showed by crash tool as below, the first stack frame is abnormal, crash> bt PID: 113 TASK: ff60000002269600 CPU: 0 COMMAND: "sh" #0 [ff2000001039bb90] __efistub_.Ldebug_info0 at 00ffffffa5537400 <-- Abnormal #1 [ff2000001039bcf0] panic at ffffffff806578ba #2 [ff2000001039bd50] sysrq_reset_seq_param_set at ffffffff8038c030 #3 [ff2000001039bda0] __handle_sysrq at ffffffff8038c5f8 #4 [ff2000001039be00] write_sysrq_trigger at ffffffff8038cad8 openbmc#5 [ff2000001039be20] proc_reg_write at ffffffff801b7edc openbmc#6 [ff2000001039be40] vfs_write at ffffffff80152ba6 openbmc#7 [ff2000001039be80] ksys_write at ffffffff80152ece openbmc#8 [ff2000001039bed0] sys_write at ffffffff80152f46 With the patch, we can get current kernel mode PC, the output as below, [ 17.607658] CPU: 0 PID: 113 Comm: sh Kdump: loaded Not tainted 5.18.9 openbmc#42 [ 17.607937] Hardware name: riscv-virtio,qemu (DT) [ 17.608150] epc : ffffffff800078f8 ra : ffffffff8008862c sp : ff20000010333b90 [ 17.608441] gp : ffffffff810dde38 tp : ff6000000226c200 t0 : ffffffff8032be68 [ 17.608741] t1 : 0720072007200720 t2 : 666666666666663c s0 : ff20000010333cf0 [ 17.609025] s1 : 0000000000000000 a0 : ff20000010333b98 a1 : 0000000000000001 [ 17.609320] a2 : 0000000000000010 a3 : 0000000000000000 a4 : 0000000000000000 [ 17.609601] a5 : ff60000001c78000 a6 : 000000000000003c a7 : ffffffff8035c9a4 [ 17.609894] s2 : ffffffff810df0a8 s3 : ffffffff810df718 s4 : ff20000010333b98 [ 17.610186] s5 : 0000000000000000 s6 : 0000000000000007 s7 : ffffffff80c4a468 [ 17.610469] s8 : 00ffffffca281410 s9 : 0000000000000007 s10: 00aaaaaab5bb6700 [ 17.610755] s11: 0000000000000001 t3 : ff60000001218f00 t4 : ff60000001218f00 [ 17.611041] t5 : ff60000001218000 t6 : ff20000010333988 [ 17.611255] status: 0000000200000020 badaddr: 0000000000000000 cause: 0000000000000008 With the correct PC, the backtrace showed by crash tool as below, crash> bt PID: 113 TASK: ff6000000226c200 CPU: 0 COMMAND: "sh" #0 [ff20000010333b90] riscv_crash_save_regs at ffffffff800078f8 <--- Normal #1 [ff20000010333cf0] panic at ffffffff806578c6 #2 [ff20000010333d50] sysrq_reset_seq_param_set at ffffffff8038c03c #3 [ff20000010333da0] __handle_sysrq at ffffffff8038c604 #4 [ff20000010333e00] write_sysrq_trigger at ffffffff8038cae4 openbmc#5 [ff20000010333e20] proc_reg_write at ffffffff801b7ee8 openbmc#6 [ff20000010333e40] vfs_write at ffffffff80152bb2 openbmc#7 [ff20000010333e80] ksys_write at ffffffff80152eda openbmc#8 [ff20000010333ed0] sys_write at ffffffff80152f52 Fixes: e53d281 ("RISC-V: Add kdump support") Co-developed-by: Guo Ren <guoren@kernel.org> Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com> Link: https://lore.kernel.org/r/20220811074150.3020189-3-xianting.tian@linux.alibaba.com Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 353d921 ] During execution of the worker that's used to register rpmsg devices we are safely locking the channels mutex but, when creating a new endpoint for such devices, we are registering a IPI on the SCP, which then makes the SCP to trigger an interrupt, lock its own mutex and in turn register more subdevices. This creates a circular locking dependency situation, as the mtk_rpmsg channels_lock will then depend on the SCP IPI lock. [ 15.447736] ====================================================== [ 15.460158] WARNING: possible circular locking dependency detected [ 15.460161] 5.17.0-next-20220324+ torvalds#399 Not tainted [ 15.460165] ------------------------------------------------------ [ 15.460166] kworker/0:3/155 is trying to acquire lock: [ 15.460170] ffff5b4d0eaf1308 (&scp->ipi_desc[i].lock){+.+.}-{4:4}, at: scp_ipi_lock+0x34/0x50 [mtk_scp_ipi] [ 15.504958] [] but task is already holding lock: [ 15.504960] ffff5b4d0e8f1918 (&mtk_subdev->channels_lock){+.+.}-{4:4}, at: mtk_register_device_work_function+0x50/0x1cc [mtk_rpmsg] [ 15.504978] [] which lock already depends on the new lock. [ 15.504980] [] the existing dependency chain (in reverse order) is: [ 15.504982] [] -> #1 (&mtk_subdev->channels_lock){+.+.}-{4:4}: [ 15.504990] lock_acquire+0x68/0x84 [ 15.504999] __mutex_lock+0xa4/0x3e0 [ 15.505007] mutex_lock_nested+0x40/0x70 [ 15.505012] mtk_rpmsg_ns_cb+0xe4/0x134 [mtk_rpmsg] [ 15.641684] mtk_rpmsg_ipi_handler+0x38/0x64 [mtk_rpmsg] [ 15.641693] scp_ipi_handler+0xbc/0x180 [mtk_scp] [ 15.663905] mt8192_scp_irq_handler+0x44/0xa4 [mtk_scp] [ 15.663915] scp_irq_handler+0x6c/0xa0 [mtk_scp] [ 15.685779] irq_thread_fn+0x34/0xa0 [ 15.685785] irq_thread+0x18c/0x240 [ 15.685789] kthread+0x104/0x110 [ 15.709579] ret_from_fork+0x10/0x20 [ 15.709586] [] -> #0 (&scp->ipi_desc[i].lock){+.+.}-{4:4}: [ 15.731271] __lock_acquire+0x11e4/0x1910 [ 15.740367] lock_acquire.part.0+0xd8/0x220 [ 15.749813] lock_acquire+0x68/0x84 [ 15.757861] __mutex_lock+0xa4/0x3e0 [ 15.766084] mutex_lock_nested+0x40/0x70 [ 15.775006] scp_ipi_lock+0x34/0x50 [mtk_scp_ipi] [ 15.785503] scp_ipi_register+0x40/0xa4 [mtk_scp_ipi] [ 15.796697] scp_register_ipi+0x1c/0x30 [mtk_scp] [ 15.807194] mtk_rpmsg_create_ept+0xa0/0x108 [mtk_rpmsg] [ 15.818912] rpmsg_create_ept+0x44/0x60 [ 15.827660] cros_ec_rpmsg_probe+0x15c/0x1f0 [ 15.837282] rpmsg_dev_probe+0x128/0x1d0 [ 15.846203] really_probe.part.0+0xa4/0x2a0 [ 15.855649] __driver_probe_device+0xa0/0x150 [ 15.865443] driver_probe_device+0x48/0x150 [ 15.877157] __device_attach_driver+0xc0/0x12c [ 15.889359] bus_for_each_drv+0x80/0xe0 [ 15.900330] __device_attach+0xe4/0x190 [ 15.911303] device_initial_probe+0x1c/0x2c [ 15.922969] bus_probe_device+0xa8/0xb0 [ 15.933927] device_add+0x3a8/0x8a0 [ 15.944193] device_register+0x28/0x40 [ 15.954970] rpmsg_register_device+0x5c/0xa0 [ 15.966782] mtk_register_device_work_function+0x148/0x1cc [mtk_rpmsg] [ 15.983146] process_one_work+0x294/0x664 [ 15.994458] worker_thread+0x7c/0x45c [ 16.005069] kthread+0x104/0x110 [ 16.014789] ret_from_fork+0x10/0x20 [ 16.025201] [] other info that might help us debug this: [ 16.047769] Possible unsafe locking scenario: [ 16.063942] CPU0 CPU1 [ 16.075166] ---- ---- [ 16.086376] lock(&mtk_subdev->channels_lock); [ 16.097592] lock(&scp->ipi_desc[i].lock); [ 16.113188] lock(&mtk_subdev->channels_lock); [ 16.129482] lock(&scp->ipi_desc[i].lock); [ 16.140020] [] *** DEADLOCK *** [ 16.158282] 4 locks held by kworker/0:3/155: [ 16.168978] #0: ffff5b4d00008748 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work+0x1fc/0x664 [ 16.190017] #1: ffff80000953bdc8 ((work_completion)(&mtk_subdev->register_work)){+.+.}-{0:0}, at: process_one_work+0x1fc/0x664 [ 16.215269] #2: ffff5b4d0e8f1918 (&mtk_subdev->channels_lock){+.+.}-{4:4}, at: mtk_register_device_work_function+0x50/0x1cc [mtk_rpmsg] [ 16.242131] #3: ffff5b4d05964190 (&dev->mutex){....}-{4:4}, at: __device_attach+0x44/0x190 To solve this, simply unlock the channels_lock mutex before calling mtk_rpmsg_register_device() and relock it right after, as safety is still ensured by the locking mechanism that happens right after through SCP. Fixes: 7017996 ("rpmsg: add rpmsg support for mt8183 SCP.") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220525091201.14210-1-angelogioacchino.delregno@collabora.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d59b73a ] Add a lock_class_key per mlx5 device to avoid a false positive "possible circular locking dependency" warning by lockdep, on flows which lock more than one mlx5 device, such as adding SF. kernel log: ====================================================== WARNING: possible circular locking dependency detected 5.19.0-rc8+ #2 Not tainted ------------------------------------------------------ kworker/u20:0/8 is trying to acquire lock: ffff88812dfe0d98 (&dev->intf_state_mutex){+.+.}-{3:3}, at: mlx5_init_one+0x2e/0x490 [mlx5_core] but task is already holding lock: ffff888101aa7898 (&(&notifier->n_head)->rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x5a/0x130 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&(&notifier->n_head)->rwsem){++++}-{3:3}: down_write+0x90/0x150 blocking_notifier_chain_register+0x53/0xa0 mlx5_sf_table_init+0x369/0x4a0 [mlx5_core] mlx5_init_one+0x261/0x490 [mlx5_core] probe_one+0x430/0x680 [mlx5_core] local_pci_probe+0xd6/0x170 work_for_cpu_fn+0x4e/0xa0 process_one_work+0x7c2/0x1340 worker_thread+0x6f6/0xec0 kthread+0x28f/0x330 ret_from_fork+0x1f/0x30 -> #0 (&dev->intf_state_mutex){+.+.}-{3:3}: __lock_acquire+0x2fc7/0x6720 lock_acquire+0x1c1/0x550 __mutex_lock+0x12c/0x14b0 mlx5_init_one+0x2e/0x490 [mlx5_core] mlx5_sf_dev_probe+0x29c/0x370 [mlx5_core] auxiliary_bus_probe+0x9d/0xe0 really_probe+0x1e0/0xaa0 __driver_probe_device+0x219/0x480 driver_probe_device+0x49/0x130 __device_attach_driver+0x1b8/0x280 bus_for_each_drv+0x123/0x1a0 __device_attach+0x1a3/0x460 bus_probe_device+0x1a2/0x260 device_add+0x9b1/0x1b40 __auxiliary_device_add+0x88/0xc0 mlx5_sf_dev_state_change_handler+0x67e/0x9d0 [mlx5_core] blocking_notifier_call_chain+0xd5/0x130 mlx5_vhca_state_work_handler+0x2b0/0x3f0 [mlx5_core] process_one_work+0x7c2/0x1340 worker_thread+0x59d/0xec0 kthread+0x28f/0x330 ret_from_fork+0x1f/0x30 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&notifier->n_head)->rwsem); lock(&dev->intf_state_mutex); lock(&(&notifier->n_head)->rwsem); lock(&dev->intf_state_mutex); *** DEADLOCK *** 4 locks held by kworker/u20:0/8: #0: ffff888150612938 ((wq_completion)mlx5_events){+.+.}-{0:0}, at: process_one_work+0x6e2/0x1340 #1: ffff888100cafdb8 ((work_completion)(&work->work)#3){+.+.}-{0:0}, at: process_one_work+0x70f/0x1340 #2: ffff888101aa7898 (&(&notifier->n_head)->rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x5a/0x130 #3: ffff88813682d0e8 (&dev->mutex){....}-{3:3}, at:__device_attach+0x76/0x460 stack backtrace: CPU: 6 PID: 8 Comm: kworker/u20:0 Not tainted 5.19.0-rc8+ Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5_events mlx5_vhca_state_work_handler [mlx5_core] Call Trace: <TASK> dump_stack_lvl+0x57/0x7d check_noncircular+0x278/0x300 ? print_circular_bug+0x460/0x460 ? lock_chain_count+0x20/0x20 ? register_lock_class+0x1880/0x1880 __lock_acquire+0x2fc7/0x6720 ? register_lock_class+0x1880/0x1880 ? register_lock_class+0x1880/0x1880 lock_acquire+0x1c1/0x550 ? mlx5_init_one+0x2e/0x490 [mlx5_core] ? lockdep_hardirqs_on_prepare+0x400/0x400 __mutex_lock+0x12c/0x14b0 ? mlx5_init_one+0x2e/0x490 [mlx5_core] ? mlx5_init_one+0x2e/0x490 [mlx5_core] ? _raw_read_unlock+0x1f/0x30 ? mutex_lock_io_nested+0x1320/0x1320 ? __ioremap_caller.constprop.0+0x306/0x490 ? mlx5_sf_dev_probe+0x269/0x370 [mlx5_core] ? iounmap+0x160/0x160 mlx5_init_one+0x2e/0x490 [mlx5_core] mlx5_sf_dev_probe+0x29c/0x370 [mlx5_core] ? mlx5_sf_dev_remove+0x130/0x130 [mlx5_core] auxiliary_bus_probe+0x9d/0xe0 really_probe+0x1e0/0xaa0 __driver_probe_device+0x219/0x480 ? auxiliary_match_id+0xe9/0x140 driver_probe_device+0x49/0x130 __device_attach_driver+0x1b8/0x280 ? driver_allows_async_probing+0x140/0x140 bus_for_each_drv+0x123/0x1a0 ? bus_for_each_dev+0x1a0/0x1a0 ? lockdep_hardirqs_on_prepare+0x286/0x400 ? trace_hardirqs_on+0x2d/0x100 __device_attach+0x1a3/0x460 ? device_driver_attach+0x1e0/0x1e0 ? kobject_uevent_env+0x22d/0xf10 bus_probe_device+0x1a2/0x260 device_add+0x9b1/0x1b40 ? dev_set_name+0xab/0xe0 ? __fw_devlink_link_to_suppliers+0x260/0x260 ? memset+0x20/0x40 ? lockdep_init_map_type+0x21a/0x7d0 __auxiliary_device_add+0x88/0xc0 ? auxiliary_device_init+0x86/0xa0 mlx5_sf_dev_state_change_handler+0x67e/0x9d0 [mlx5_core] blocking_notifier_call_chain+0xd5/0x130 mlx5_vhca_state_work_handler+0x2b0/0x3f0 [mlx5_core] ? mlx5_vhca_event_arm+0x100/0x100 [mlx5_core] ? lock_downgrade+0x6e0/0x6e0 ? lockdep_hardirqs_on_prepare+0x286/0x400 process_one_work+0x7c2/0x1340 ? lockdep_hardirqs_on_prepare+0x400/0x400 ? pwq_dec_nr_in_flight+0x230/0x230 ? rwlock_bug.part.0+0x90/0x90 worker_thread+0x59d/0xec0 ? process_one_work+0x1340/0x1340 kthread+0x28f/0x330 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x1f/0x30 </TASK> Fixes: 6a32732 ("net/mlx5: SF, Port function state change support") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Shay Drory <shayd@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b40130b ] We have been hitting the following lockdep splat with btrfs/187 recently WARNING: possible circular locking dependency detected 5.19.0-rc8+ torvalds#775 Not tainted ------------------------------------------------------ btrfs/752500 is trying to acquire lock: ffff97e1875a97b8 (btrfs-treloc-02#2){+.+.}-{3:3}, at: __btrfs_tree_lock+0x24/0x110 but task is already holding lock: ffff97e1875a9278 (btrfs-tree-01/1){+.+.}-{3:3}, at: __btrfs_tree_lock+0x24/0x110 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (btrfs-tree-01/1){+.+.}-{3:3}: down_write_nested+0x41/0x80 __btrfs_tree_lock+0x24/0x110 btrfs_init_new_buffer+0x7d/0x2c0 btrfs_alloc_tree_block+0x120/0x3b0 __btrfs_cow_block+0x136/0x600 btrfs_cow_block+0x10b/0x230 btrfs_search_slot+0x53b/0xb70 btrfs_lookup_inode+0x2a/0xa0 __btrfs_update_delayed_inode+0x5f/0x280 btrfs_async_run_delayed_root+0x24c/0x290 btrfs_work_helper+0xf2/0x3e0 process_one_work+0x271/0x590 worker_thread+0x52/0x3b0 kthread+0xf0/0x120 ret_from_fork+0x1f/0x30 -> #1 (btrfs-tree-01){++++}-{3:3}: down_write_nested+0x41/0x80 __btrfs_tree_lock+0x24/0x110 btrfs_search_slot+0x3c3/0xb70 do_relocation+0x10c/0x6b0 relocate_tree_blocks+0x317/0x6d0 relocate_block_group+0x1f1/0x560 btrfs_relocate_block_group+0x23e/0x400 btrfs_relocate_chunk+0x4c/0x140 btrfs_balance+0x755/0xe40 btrfs_ioctl+0x1ea2/0x2c90 __x64_sys_ioctl+0x88/0xc0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd -> #0 (btrfs-treloc-02#2){+.+.}-{3:3}: __lock_acquire+0x1122/0x1e10 lock_acquire+0xc2/0x2d0 down_write_nested+0x41/0x80 __btrfs_tree_lock+0x24/0x110 btrfs_lock_root_node+0x31/0x50 btrfs_search_slot+0x1cb/0xb70 replace_path+0x541/0x9f0 merge_reloc_root+0x1d6/0x610 merge_reloc_roots+0xe2/0x260 relocate_block_group+0x2c8/0x560 btrfs_relocate_block_group+0x23e/0x400 btrfs_relocate_chunk+0x4c/0x140 btrfs_balance+0x755/0xe40 btrfs_ioctl+0x1ea2/0x2c90 __x64_sys_ioctl+0x88/0xc0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd other info that might help us debug this: Chain exists of: btrfs-treloc-02#2 --> btrfs-tree-01 --> btrfs-tree-01/1 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(btrfs-tree-01/1); lock(btrfs-tree-01); lock(btrfs-tree-01/1); lock(btrfs-treloc-02#2); *** DEADLOCK *** 7 locks held by btrfs/752500: #0: ffff97e292fdf460 (sb_writers#12){.+.+}-{0:0}, at: btrfs_ioctl+0x208/0x2c90 #1: ffff97e284c02050 (&fs_info->reclaim_bgs_lock){+.+.}-{3:3}, at: btrfs_balance+0x55f/0xe40 #2: ffff97e284c00878 (&fs_info->cleaner_mutex){+.+.}-{3:3}, at: btrfs_relocate_block_group+0x236/0x400 #3: ffff97e292fdf650 (sb_internal#2){.+.+}-{0:0}, at: merge_reloc_root+0xef/0x610 #4: ffff97e284c02378 (btrfs_trans_num_writers){++++}-{0:0}, at: join_transaction+0x1a8/0x5a0 openbmc#5: ffff97e284c023a0 (btrfs_trans_num_extwriters){++++}-{0:0}, at: join_transaction+0x1a8/0x5a0 openbmc#6: ffff97e1875a9278 (btrfs-tree-01/1){+.+.}-{3:3}, at: __btrfs_tree_lock+0x24/0x110 stack backtrace: CPU: 1 PID: 752500 Comm: btrfs Not tainted 5.19.0-rc8+ torvalds#775 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014 Call Trace: dump_stack_lvl+0x56/0x73 check_noncircular+0xd6/0x100 ? lock_is_held_type+0xe2/0x140 __lock_acquire+0x1122/0x1e10 lock_acquire+0xc2/0x2d0 ? __btrfs_tree_lock+0x24/0x110 down_write_nested+0x41/0x80 ? __btrfs_tree_lock+0x24/0x110 __btrfs_tree_lock+0x24/0x110 btrfs_lock_root_node+0x31/0x50 btrfs_search_slot+0x1cb/0xb70 ? lock_release+0x137/0x2d0 ? _raw_spin_unlock+0x29/0x50 ? release_extent_buffer+0x128/0x180 replace_path+0x541/0x9f0 merge_reloc_root+0x1d6/0x610 merge_reloc_roots+0xe2/0x260 relocate_block_group+0x2c8/0x560 btrfs_relocate_block_group+0x23e/0x400 btrfs_relocate_chunk+0x4c/0x140 btrfs_balance+0x755/0xe40 btrfs_ioctl+0x1ea2/0x2c90 ? lock_is_held_type+0xe2/0x140 ? lock_is_held_type+0xe2/0x140 ? __x64_sys_ioctl+0x88/0xc0 __x64_sys_ioctl+0x88/0xc0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd This isn't necessarily new, it's just tricky to hit in practice. There are two competing things going on here. With relocation we create a snapshot of every fs tree with a reloc tree. Any extent buffers that get initialized here are initialized with the reloc root lockdep key. However since it is a snapshot, any blocks that are currently in cache that originally belonged to the fs tree will have the normal tree lockdep key set. This creates the lock dependency of reloc tree -> normal tree for the extent buffer locking during the first phase of the relocation as we walk down the reloc root to relocate blocks. However this is problematic because the final phase of the relocation is merging the reloc root into the original fs root. This involves searching down to any keys that exist in the original fs root and then swapping the relocated block and the original fs root block. We have to search down to the fs root first, and then go search the reloc root for the block we need to replace. This creates the dependency of normal tree -> reloc tree which is why lockdep complains. Additionally even if we were to fix this particular mismatch with a different nesting for the merge case, we're still slotting in a block that has a owner of the reloc root objectid into a normal tree, so that block will have its lockdep key set to the tree reloc root, and create a lockdep splat later on when we wander into that block from the fs root. Unfortunately the only solution here is to make sure we do not set the lockdep key to the reloc tree lockdep key normally, and then reset any blocks we wander into from the reloc root when we're doing the merged. This solves the problem of having mixed tree reloc keys intermixed with normal tree keys, and then allows us to make sure in the merge case we maintain the lock order of normal tree -> reloc tree We handle this by setting a bit on the reloc root when we do the search for the block we want to relocate, and any block we search into or COW at that point gets set to the reloc tree key. This works correctly because we only ever COW down to the parent node, so we aren't resetting the key for the block we're linking into the fs root. With this patch we no longer have the lockdep splat in btrfs/187. Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 9c6d778 upstream. Automatic kernel fuzzing revealed a recursive locking violation in usb-storage: ============================================ WARNING: possible recursive locking detected 5.18.0 #3 Not tainted -------------------------------------------- kworker/1:3/1205 is trying to acquire lock: ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at: usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230 but task is already holding lock: ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at: usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230 ... stack backtrace: CPU: 1 PID: 1205 Comm: kworker/1:3 Not tainted 5.18.0 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_deadlock_bug kernel/locking/lockdep.c:2988 [inline] check_deadlock kernel/locking/lockdep.c:3031 [inline] validate_chain kernel/locking/lockdep.c:3816 [inline] __lock_acquire.cold+0x152/0x3ca kernel/locking/lockdep.c:5053 lock_acquire kernel/locking/lockdep.c:5665 [inline] lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5630 __mutex_lock_common kernel/locking/mutex.c:603 [inline] __mutex_lock+0x14f/0x1610 kernel/locking/mutex.c:747 usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230 usb_reset_device+0x37d/0x9a0 drivers/usb/core/hub.c:6109 r871xu_dev_remove+0x21a/0x270 drivers/staging/rtl8712/usb_intf.c:622 usb_unbind_interface+0x1bd/0x890 drivers/usb/core/driver.c:458 device_remove drivers/base/dd.c:545 [inline] device_remove+0x11f/0x170 drivers/base/dd.c:537 __device_release_driver drivers/base/dd.c:1222 [inline] device_release_driver_internal+0x1a7/0x2f0 drivers/base/dd.c:1248 usb_driver_release_interface+0x102/0x180 drivers/usb/core/driver.c:627 usb_forced_unbind_intf+0x4d/0xa0 drivers/usb/core/driver.c:1118 usb_reset_device+0x39b/0x9a0 drivers/usb/core/hub.c:6114 This turned out not to be an error in usb-storage but rather a nested device reset attempt. That is, as the rtl8712 driver was being unbound from a composite device in preparation for an unrelated USB reset (that driver does not have pre_reset or post_reset callbacks), its ->remove routine called usb_reset_device() -- thus nesting one reset call within another. Performing a reset as part of disconnect processing is a questionable practice at best. However, the bug report points out that the USB core does not have any protection against nested resets. Adding a reset_in_progress flag and testing it will prevent such errors in the future. Link: https://lore.kernel.org/all/CAB7eexKUpvX-JNiLzhXBDWgfg2T9e9_0Tw4HQ6keN==voRbP0g@mail.gmail.com/ Cc: stable@vger.kernel.org Reported-and-tested-by: Rondreis <linhaoguo86@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/YwkflDxvg0KWqyZK@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ac56a0b ] Because rxrpc pretends to be a tunnel on top of a UDP/UDP6 socket, allowing it to siphon off UDP packets early in the handling of received UDP packets thereby avoiding the packet going through the UDP receive queue, it doesn't get ICMP packets through the UDP ->sk_error_report() callback. In fact, it doesn't appear that there's any usable option for getting hold of ICMP packets. Fix this by adding a new UDP encap hook to distribute error messages for UDP tunnels. If the hook is set, then the tunnel driver will be able to see ICMP packets. The hook provides the offset into the packet of the UDP header of the original packet that caused the notification. An alternative would be to call the ->error_handler() hook - but that requires that the skbuff be cloned (as ip_icmp_error() or ipv6_cmp_error() do, though isn't really necessary or desirable in rxrpc's case is we want to parse them there and then, not queue them). Changes ======= ver #3) - Fixed an uninitialised variable. ver #2) - Fixed some missing CONFIG_AF_RXRPC_IPV6 conditionals. Fixes: 5271953 ("rxrpc: Use the UDP encap_rcv hook") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 84a5358 ] The SRv6 layer allows defining HMAC data that can later be used to sign IPv6 Segment Routing Headers. This configuration is realised via netlink through four attributes: SEG6_ATTR_HMACKEYID, SEG6_ATTR_SECRET, SEG6_ATTR_SECRETLEN and SEG6_ATTR_ALGID. Because the SECRETLEN attribute is decoupled from the actual length of the SECRET attribute, it is possible to provide invalid combinations (e.g., secret = "", secretlen = 64). This case is not checked in the code and with an appropriately crafted netlink message, an out-of-bounds read of up to 64 bytes (max secret length) can occur past the skb end pointer and into skb_shared_info: Breakpoint 1, seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208 208 memcpy(hinfo->secret, secret, slen); (gdb) bt #0 seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208 #1 0xffffffff81e012e9 in genl_family_rcv_msg_doit (skb=skb@entry=0xffff88800b1f9f00, nlh=nlh@entry=0xffff88800b1b7600, extack=extack@entry=0xffffc90000ba7af0, ops=ops@entry=0xffffc90000ba7a80, hdrlen=4, net=0xffffffff84237580 <init_net>, family=<optimized out>, family=<optimized out>) at net/netlink/genetlink.c:731 #2 0xffffffff81e01435 in genl_family_rcv_msg (extack=0xffffc90000ba7af0, nlh=0xffff88800b1b7600, skb=0xffff88800b1f9f00, family=0xffffffff82fef6c0 <seg6_genl_family>) at net/netlink/genetlink.c:775 #3 genl_rcv_msg (skb=0xffff88800b1f9f00, nlh=0xffff88800b1b7600, extack=0xffffc90000ba7af0) at net/netlink/genetlink.c:792 #4 0xffffffff81dfffc3 in netlink_rcv_skb (skb=skb@entry=0xffff88800b1f9f00, cb=cb@entry=0xffffffff81e01350 <genl_rcv_msg>) at net/netlink/af_netlink.c:2501 openbmc#5 0xffffffff81e00919 in genl_rcv (skb=0xffff88800b1f9f00) at net/netlink/genetlink.c:803 openbmc#6 0xffffffff81dff6ae in netlink_unicast_kernel (ssk=0xffff888010eec800, skb=0xffff88800b1f9f00, sk=0xffff888004aed000) at net/netlink/af_netlink.c:1319 openbmc#7 netlink_unicast (ssk=ssk@entry=0xffff888010eec800, skb=skb@entry=0xffff88800b1f9f00, portid=portid@entry=0, nonblock=<optimized out>) at net/netlink/af_netlink.c:1345 openbmc#8 0xffffffff81dff9a4 in netlink_sendmsg (sock=<optimized out>, msg=0xffffc90000ba7e48, len=<optimized out>) at net/netlink/af_netlink.c:1921 ... (gdb) p/x ((struct sk_buff *)0xffff88800b1f9f00)->head + ((struct sk_buff *)0xffff88800b1f9f00)->end $1 = 0xffff88800b1b76c0 (gdb) p/x secret $2 = 0xffff88800b1b76c0 (gdb) p slen $3 = 64 '@' The OOB data can then be read back from userspace by dumping HMAC state. This commit fixes this by ensuring SECRETLEN cannot exceed the actual length of SECRET. Reported-by: Lucas Leong <wmliang.tw@gmail.com> Tested: verified that EINVAL is correctly returned when secretlen > len(secret) Fixes: 4f4853d ("ipv6: sr: implement API to control SR HMAC structure") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2f44013 ] During stress testing with CONFIG_SMP disabled, KASAN reports as below: ================================================================== BUG: KASAN: use-after-free in __mutex_lock+0xe5/0xc30 Read of size 8 at addr ffff8881094223f8 by task stress/7789 CPU: 0 PID: 7789 Comm: stress Not tainted 6.0.0-rc1-00002-g0d53d2e882f9 #3 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Call Trace: <TASK> .. __mutex_lock+0xe5/0xc30 .. z_erofs_do_read_page+0x8ce/0x1560 .. z_erofs_readahead+0x31c/0x580 .. Freed by task 7787 kasan_save_stack+0x1e/0x40 kasan_set_track+0x20/0x30 kasan_set_free_info+0x20/0x40 __kasan_slab_free+0x10c/0x190 kmem_cache_free+0xed/0x380 rcu_core+0x3d5/0xc90 __do_softirq+0x12d/0x389 Last potentially related work creation: kasan_save_stack+0x1e/0x40 __kasan_record_aux_stack+0x97/0xb0 call_rcu+0x3d/0x3f0 erofs_shrink_workstation+0x11f/0x210 erofs_shrink_scan+0xdc/0x170 shrink_slab.constprop.0+0x296/0x530 drop_slab+0x1c/0x70 drop_caches_sysctl_handler+0x70/0x80 proc_sys_call_handler+0x20a/0x2f0 vfs_write+0x555/0x6c0 ksys_write+0xbe/0x160 do_syscall_64+0x3b/0x90 The root cause is that erofs_workgroup_unfreeze() doesn't reset to orig_val thus it causes a race that the pcluster reuses unexpectedly before freeing. Since UP platforms are quite rare now, such path becomes unnecessary. Let's drop such specific-designed path directly instead. Fixes: 73f5c66 ("staging: erofs: fix `erofs_workgroup_{try_to_freeze, unfreeze}'") Reviewed-by: Yue Hu <huyue2@coolpad.com> Reviewed-by: Chao Yu <chao@kernel.org> Link: https://lore.kernel.org/r/20220902045710.109530-1-hsiangkao@linux.alibaba.com Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

Add the new mode (called as mode#3) to monitor speed and control the PWM. Initialize mode #3 by default (fan tach input enable and PWM mode enable). We can reconfigure again by the pwm_enale setting. Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>

[ Upstream commit 05bb016 ] ACPICA commit 770653e3ba67c30a629ca7d12e352d83c2541b1e Before this change we see the following UBSAN stack trace in Fuchsia: #0 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302 #1.2 0x000020d0f660777f in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x3d77f #1.1 0x000020d0f660777f in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x3d77f #1 0x000020d0f660777f in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:387 <libclang_rt.asan.so>+0x3d77f #2 0x000020d0f660b96d in handlepointer_overflow_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:809 <libclang_rt.asan.so>+0x4196d #3 0x000020d0f660b50d in compiler-rt/lib/ubsan/ubsan_handlers.cpp:815 <libclang_rt.asan.so>+0x4150d #4 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302 openbmc#5 0x000021e4213e2369 in acpi_ds_call_control_method(struct acpi_thread_state*, struct acpi_walk_state*, union acpi_parse_object*) ../../third_party/acpica/source/components/dispatcher/dsmethod.c:605 <platform-bus-x86.so>+0x262369 openbmc#6 0x000021e421437fac in acpi_ps_parse_aml(struct acpi_walk_state*) ../../third_party/acpica/source/components/parser/psparse.c:550 <platform-bus-x86.so>+0x2b7fac openbmc#7 0x000021e4214464d2 in acpi_ps_execute_method(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/parser/psxface.c:244 <platform-bus-x86.so>+0x2c64d2 openbmc#8 0x000021e4213aa052 in acpi_ns_evaluate(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/namespace/nseval.c:250 <platform-bus-x86.so>+0x22a052 openbmc#9 0x000021e421413dd8 in acpi_ns_init_one_device(acpi_handle, u32, void*, void**) ../../third_party/acpica/source/components/namespace/nsinit.c:735 <platform-bus-x86.so>+0x293dd8 openbmc#10 0x000021e421429e98 in acpi_ns_walk_namespace(acpi_object_type, acpi_handle, u32, u32, acpi_walk_callback, acpi_walk_callback, void*, void**) ../../third_party/acpica/source/components/namespace/nswalk.c:298 <platform-bus-x86.so>+0x2a9e98 openbmc#11 0x000021e4214131ac in acpi_ns_initialize_devices(u32) ../../third_party/acpica/source/components/namespace/nsinit.c:268 <platform-bus-x86.so>+0x2931ac openbmc#12 0x000021e42147c40d in acpi_initialize_objects(u32) ../../third_party/acpica/source/components/utilities/utxfinit.c:304 <platform-bus-x86.so>+0x2fc40d openbmc#13 0x000021e42126d603 in acpi::acpi_impl::initialize_acpi(acpi::acpi_impl*) ../../src/devices/board/lib/acpi/acpi-impl.cc:224 <platform-bus-x86.so>+0xed603 Add a simple check that avoids incrementing a pointer by zero, but otherwise behaves as before. Note that our findings are against ACPICA 20221020, but the same code exists on master. Link: acpica/acpica@770653e3 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ef6e199 ] In the function ieee80211_tx_dequeue() there is a particular locking sequence: begin: spin_lock(&local->queue_stop_reason_lock); q_stopped = local->queue_stop_reasons[q]; spin_unlock(&local->queue_stop_reason_lock); However small the chance (increased by ftracetest), an asynchronous interrupt can occur in between of spin_lock() and spin_unlock(), and the interrupt routine will attempt to lock the same &local->queue_stop_reason_lock again. This will cause a costly reset of the CPU and the wifi device or an altogether hang in the single CPU and single core scenario. The only remaining spin_lock(&local->queue_stop_reason_lock) that did not disable interrupts was patched, which should prevent any deadlocks on the same CPU/core and the same wifi device. This is the probable trace of the deadlock: kernel: ================================ kernel: WARNING: inconsistent lock state kernel: 6.3.0-rc6-mt-20230401-00001-gf86822a1170f #4 Tainted: G W kernel: -------------------------------- kernel: inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. kernel: kworker/5:0/25656 [HC0[0]:SC0[0]:HE1:SE1] takes: kernel: ffff9d6190779478 (&local->queue_stop_reason_lock){+.?.}-{2:2}, at: return_to_handler+0x0/0x40 kernel: {IN-SOFTIRQ-W} state was registered at: kernel: lock_acquire+0xc7/0x2d0 kernel: _raw_spin_lock+0x36/0x50 kernel: ieee80211_tx_dequeue+0xb4/0x1330 [mac80211] kernel: iwl_mvm_mac_itxq_xmit+0xae/0x210 [iwlmvm] kernel: iwl_mvm_mac_wake_tx_queue+0x2d/0xd0 [iwlmvm] kernel: ieee80211_queue_skb+0x450/0x730 [mac80211] kernel: __ieee80211_xmit_fast.constprop.66+0x834/0xa50 [mac80211] kernel: __ieee80211_subif_start_xmit+0x217/0x530 [mac80211] kernel: ieee80211_subif_start_xmit+0x60/0x580 [mac80211] kernel: dev_hard_start_xmit+0xb5/0x260 kernel: __dev_queue_xmit+0xdbe/0x1200 kernel: neigh_resolve_output+0x166/0x260 kernel: ip_finish_output2+0x216/0xb80 kernel: __ip_finish_output+0x2a4/0x4d0 kernel: ip_finish_output+0x2d/0xd0 kernel: ip_output+0x82/0x2b0 kernel: ip_local_out+0xec/0x110 kernel: igmpv3_sendpack+0x5c/0x90 kernel: igmp_ifc_timer_expire+0x26e/0x4e0 kernel: call_timer_fn+0xa5/0x230 kernel: run_timer_softirq+0x27f/0x550 kernel: __do_softirq+0xb4/0x3a4 kernel: irq_exit_rcu+0x9b/0xc0 kernel: sysvec_apic_timer_interrupt+0x80/0xa0 kernel: asm_sysvec_apic_timer_interrupt+0x1f/0x30 kernel: _raw_spin_unlock_irqrestore+0x3f/0x70 kernel: free_to_partial_list+0x3d6/0x590 kernel: __slab_free+0x1b7/0x310 kernel: kmem_cache_free+0x52d/0x550 kernel: putname+0x5d/0x70 kernel: do_sys_openat2+0x1d7/0x310 kernel: do_sys_open+0x51/0x80 kernel: __x64_sys_openat+0x24/0x30 kernel: do_syscall_64+0x5c/0x90 kernel: entry_SYSCALL_64_after_hwframe+0x72/0xdc kernel: irq event stamp: 5120729 kernel: hardirqs last enabled at (5120729): [<ffffffff9d149936>] trace_graph_return+0xd6/0x120 kernel: hardirqs last disabled at (5120728): [<ffffffff9d149950>] trace_graph_return+0xf0/0x120 kernel: softirqs last enabled at (5069900): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40 kernel: softirqs last disabled at (5067555): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40 kernel: other info that might help us debug this: kernel: Possible unsafe locking scenario: kernel: CPU0 kernel: ---- kernel: lock(&local->queue_stop_reason_lock); kernel: <Interrupt> kernel: lock(&local->queue_stop_reason_lock); kernel: *** DEADLOCK *** kernel: 8 locks held by kworker/5:0/25656: kernel: #0: ffff9d618009d138 ((wq_completion)events_freezable){+.+.}-{0:0}, at: process_one_work+0x1ca/0x530 kernel: #1: ffffb1ef4637fe68 ((work_completion)(&local->restart_work)){+.+.}-{0:0}, at: process_one_work+0x1ce/0x530 kernel: #2: ffffffff9f166548 (rtnl_mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: #3: ffff9d6190778728 (&rdev->wiphy.mtx){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: #4: ffff9d619077b480 (&mvm->mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: openbmc#5: ffff9d61907bacd8 (&trans_pcie->mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: openbmc#6: ffffffff9ef9cda0 (rcu_read_lock){....}-{1:2}, at: iwl_mvm_queue_state_change+0x59/0x3a0 [iwlmvm] kernel: openbmc#7: ffffffff9ef9cda0 (rcu_read_lock){....}-{1:2}, at: iwl_mvm_mac_itxq_xmit+0x42/0x210 [iwlmvm] kernel: stack backtrace: kernel: CPU: 5 PID: 25656 Comm: kworker/5:0 Tainted: G W 6.3.0-rc6-mt-20230401-00001-gf86822a1170f #4 kernel: Hardware name: LENOVO 82H8/LNVNB161216, BIOS GGCN51WW 11/16/2022 kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211] kernel: Call Trace: kernel: <TASK> kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: dump_stack_lvl+0x5f/0xa0 kernel: dump_stack+0x14/0x20 kernel: print_usage_bug.part.46+0x208/0x2a0 kernel: mark_lock.part.47+0x605/0x630 kernel: ? sched_clock+0xd/0x20 kernel: ? trace_clock_local+0x14/0x30 kernel: ? __rb_reserve_next+0x5f/0x490 kernel: ? _raw_spin_lock+0x1b/0x50 kernel: __lock_acquire+0x464/0x1990 kernel: ? mark_held_locks+0x4e/0x80 kernel: lock_acquire+0xc7/0x2d0 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ? ftrace_return_to_handler+0x8b/0x100 kernel: ? preempt_count_add+0x4/0x70 kernel: _raw_spin_lock+0x36/0x50 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ieee80211_tx_dequeue+0xb4/0x1330 [mac80211] kernel: ? prepare_ftrace_return+0xc5/0x190 kernel: ? ftrace_graph_func+0x16/0x20 kernel: ? 0xffffffffc02ab0b1 kernel: ? lock_acquire+0xc7/0x2d0 kernel: ? iwl_mvm_mac_itxq_xmit+0x42/0x210 [iwlmvm] kernel: ? ieee80211_tx_dequeue+0x9/0x1330 [mac80211] kernel: ? __rcu_read_lock+0x4/0x40 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_mac_itxq_xmit+0xae/0x210 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_queue_state_change+0x311/0x3a0 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_wake_sw_queue+0x17/0x20 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_txq_gen2_unmap+0x1c9/0x1f0 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_txq_gen2_free+0x55/0x130 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_txq_gen2_tx_free+0x63/0x80 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: _iwl_trans_pcie_gen2_stop_device+0x3f3/0x5b0 [iwlwifi] kernel: ? _iwl_trans_pcie_gen2_stop_device+0x9/0x5b0 [iwlwifi] kernel: ? mutex_lock_nested+0x4/0x30 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_trans_pcie_gen2_stop_device+0x5f/0x90 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_stop_device+0x78/0xd0 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: __iwl_mvm_mac_start+0x114/0x210 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_mac_start+0x76/0x150 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: drv_start+0x79/0x180 [mac80211] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ieee80211_reconfig+0x1523/0x1ce0 [mac80211] kernel: ? synchronize_net+0x4/0x50 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ieee80211_restart_work+0x108/0x170 [mac80211] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: process_one_work+0x250/0x530 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: worker_thread+0x48/0x3a0 kernel: ? __pfx_worker_thread+0x10/0x10 kernel: kthread+0x10f/0x140 kernel: ? __pfx_kthread+0x10/0x10 kernel: ret_from_fork+0x29/0x50 kernel: </TASK> Fixes: 4444bc2 ("wifi: mac80211: Proper mark iTXQs for resumption") Link: https://lore.kernel.org/all/1f58a0d1-d2b9-d851-73c3-93fcc607501c@alu.unizg.hr/ Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Cc: Gregory Greenman <gregory.greenman@intel.com> Cc: Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/all/cdc80531-f25f-6f9d-b15f-25e16130b53a@alu.unizg.hr/ Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: Alexander Wetzel <alexander@wetzel-home.de> Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: tag, or it goes automatically? Link: https://lore.kernel.org/r/20230425164005.25272-1-mirsad.todorovac@alu.unizg.hr Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 614ce6a upstream. When the dwc3 device is runtime suspended, various required clocks are in disabled state and it is not guaranteed that access to any registers would work. Depending on the SoC glue, a register read could be as benign as returning 0 or be fatal enough to hang the system. In order to prevent such scenarios of fatal errors, make sure to resume dwc3 then allow the function to proceed. Fixes: 72246da ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable@vger.kernel.org #3.2: 30332ee: debugfs: regset32: Add Runtime PM support Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20230509144836.6803-1-quic_ugoswami@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the new mode (called as mode#3) to monitor speed and control the PWM. Initialize mode #3 by default (fan tach input enable and PWM mode enable). We can reconfigure again by the pwm_enale setting. Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>

[ Upstream commit f8bbc07 ] vhost_worker will call tun call backs to receive packets. If too many illegal packets arrives, tun_do_read will keep dumping packet contents. When console is enabled, it will costs much more cpu time to dump packet and soft lockup will be detected. net_ratelimit mechanism can be used to limit the dumping rate. PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980" #0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253 #1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3 #2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e #3 [fffffe00003fced0] do_nmi at ffffffff8922660d #4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663 [exception RIP: io_serial_in+20] RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002 RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0 RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020 R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 openbmc#5 [ffffa655314979e8] io_serial_in at ffffffff89792594 openbmc#6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470 openbmc#7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6 openbmc#8 [ffffa65531497a20] uart_console_write at ffffffff8978b605 openbmc#9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558 openbmc#10 [ffffa65531497ac8] console_unlock at ffffffff89316124 openbmc#11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07 openbmc#12 [ffffa65531497b68] printk at ffffffff89318306 openbmc#13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765 openbmc#14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun] openbmc#15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun] openbmc#16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net] openbmc#17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost] openbmc#18 [ffffa65531497f10] kthread at ffffffff892d2e72 openbmc#19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f Fixes: ef3db4a ("tun: avoid BUG, dump packet on GSO errors") Signed-off-by: Lei Chen <lei.chen@smartx.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 9e985cb upstream. Drop support for virtualizing adaptive PEBS, as KVM's implementation is architecturally broken without an obvious/easy path forward, and because exposing adaptive PEBS can leak host LBRs to the guest, i.e. can leak host kernel addresses to the guest. Bug #1 is that KVM doesn't account for the upper 32 bits of IA32_FIXED_CTR_CTRL when (re)programming fixed counters, e.g fixed_ctrl_field() drops the upper bits, reprogram_fixed_counters() stores local variables as u8s and truncates the upper bits too, etc. Bug #2 is that, because KVM _always_ sets precise_ip to a non-zero value for PEBS events, perf will _always_ generate an adaptive record, even if the guest requested a basic record. Note, KVM will also enable adaptive PEBS in individual *counter*, even if adaptive PEBS isn't exposed to the guest, but this is benign as MSR_PEBS_DATA_CFG is guaranteed to be zero, i.e. the guest will only ever see Basic records. Bug #3 is in perf. intel_pmu_disable_fixed() doesn't clear the upper bits either, i.e. leaves ICL_FIXED_0_ADAPTIVE set, and intel_pmu_enable_fixed() effectively doesn't clear ICL_FIXED_0_ADAPTIVE either. I.e. perf _always_ enables ADAPTIVE counters, regardless of what KVM requests. Bug #4 is that adaptive PEBS *might* effectively bypass event filters set by the host, as "Updated Memory Access Info Group" records information that might be disallowed by userspace via KVM_SET_PMU_EVENT_FILTER. Bug openbmc#5 is that KVM doesn't ensure LBR MSRs hold guest values (or at least zeros) when entering a vCPU with adaptive PEBS, which allows the guest to read host LBRs, i.e. host RIPs/addresses, by enabling "LBR Entries" records. Disable adaptive PEBS support as an immediate fix due to the severity of the LBR leak in particular, and because fixing all of the bugs will be non-trivial, e.g. not suitable for backporting to stable kernels. Note! This will break live migration, but trying to make KVM play nice with live migration would be quite complicated, wouldn't be guaranteed to work (i.e. KVM might still kill/confuse the guest), and it's not clear that there are any publicly available VMMs that support adaptive PEBS, let alone live migrate VMs that support adaptive PEBS, e.g. QEMU doesn't support PEBS in any capacity. Link: https://lore.kernel.org/all/20240306230153.786365-1-seanjc@google.com Link: https://lore.kernel.org/all/ZeepGjHCeSfadANM@google.com Fixes: c59a1f1 ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS") Cc: stable@vger.kernel.org Cc: Like Xu <like.xu.linux@gmail.com> Cc: Mingwei Zhang <mizhang@google.com> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Zhang Xiong <xiong.y.zhang@intel.com> Cc: Lv Zhiyuan <zhiyuan.lv@intel.com> Cc: Dapeng Mi <dapeng1.mi@intel.com> Cc: Jim Mattson <jmattson@google.com> Acked-by: Like Xu <likexu@tencent.com> Link: https://lore.kernel.org/r/20240307005833.827147-1-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1983184 upstream. When I did hard offline test with hugetlb pages, below deadlock occurs: ====================================================== WARNING: possible circular locking dependency detected 6.8.0-11409-gf6cef5f8c37f #1 Not tainted ------------------------------------------------------ bash/46904 is trying to acquire lock: ffffffffabe68910 (cpu_hotplug_lock){++++}-{0:0}, at: static_key_slow_dec+0x16/0x60 but task is already holding lock: ffffffffabf92ea8 (pcp_batch_high_lock){+.+.}-{3:3}, at: zone_pcp_disable+0x16/0x40 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (pcp_batch_high_lock){+.+.}-{3:3}: __mutex_lock+0x6c/0x770 page_alloc_cpu_online+0x3c/0x70 cpuhp_invoke_callback+0x397/0x5f0 __cpuhp_invoke_callback_range+0x71/0xe0 _cpu_up+0xeb/0x210 cpu_up+0x91/0xe0 cpuhp_bringup_mask+0x49/0xb0 bringup_nonboot_cpus+0xb7/0xe0 smp_init+0x25/0xa0 kernel_init_freeable+0x15f/0x3e0 kernel_init+0x15/0x1b0 ret_from_fork+0x2f/0x50 ret_from_fork_asm+0x1a/0x30 -> #0 (cpu_hotplug_lock){++++}-{0:0}: __lock_acquire+0x1298/0x1cd0 lock_acquire+0xc0/0x2b0 cpus_read_lock+0x2a/0xc0 static_key_slow_dec+0x16/0x60 __hugetlb_vmemmap_restore_folio+0x1b9/0x200 dissolve_free_huge_page+0x211/0x260 __page_handle_poison+0x45/0xc0 memory_failure+0x65e/0xc70 hard_offline_page_store+0x55/0xa0 kernfs_fop_write_iter+0x12c/0x1d0 vfs_write+0x387/0x550 ksys_write+0x64/0xe0 do_syscall_64+0xca/0x1e0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(pcp_batch_high_lock); lock(cpu_hotplug_lock); lock(pcp_batch_high_lock); rlock(cpu_hotplug_lock); *** DEADLOCK *** 5 locks held by bash/46904: #0: ffff98f6c3bb23f0 (sb_writers#5){.+.+}-{0:0}, at: ksys_write+0x64/0xe0 #1: ffff98f6c328e488 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0xf8/0x1d0 #2: ffff98ef83b31890 (kn->active#113){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x100/0x1d0 #3: ffffffffabf9db48 (mf_mutex){+.+.}-{3:3}, at: memory_failure+0x44/0xc70 #4: ffffffffabf92ea8 (pcp_batch_high_lock){+.+.}-{3:3}, at: zone_pcp_disable+0x16/0x40 stack backtrace: CPU: 10 PID: 46904 Comm: bash Kdump: loaded Not tainted 6.8.0-11409-gf6cef5f8c37f #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x68/0xa0 check_noncircular+0x129/0x140 __lock_acquire+0x1298/0x1cd0 lock_acquire+0xc0/0x2b0 cpus_read_lock+0x2a/0xc0 static_key_slow_dec+0x16/0x60 __hugetlb_vmemmap_restore_folio+0x1b9/0x200 dissolve_free_huge_page+0x211/0x260 __page_handle_poison+0x45/0xc0 memory_failure+0x65e/0xc70 hard_offline_page_store+0x55/0xa0 kernfs_fop_write_iter+0x12c/0x1d0 vfs_write+0x387/0x550 ksys_write+0x64/0xe0 do_syscall_64+0xca/0x1e0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 RIP: 0033:0x7fc862314887 Code: 10 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24 RSP: 002b:00007fff19311268 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007fc862314887 RDX: 000000000000000c RSI: 000056405645fe10 RDI: 0000000000000001 RBP: 000056405645fe10 R08: 00007fc8623d1460 R09: 000000007fffffff R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000000c R13: 00007fc86241b780 R14: 00007fc862417600 R15: 00007fc862416a00 In short, below scene breaks the lock dependency chain: memory_failure __page_handle_poison zone_pcp_disable -- lock(pcp_batch_high_lock) dissolve_free_huge_page __hugetlb_vmemmap_restore_folio static_key_slow_dec cpus_read_lock -- rlock(cpu_hotplug_lock) Fix this by calling drain_all_pages() instead. This issue won't occur until commit a6b4085 ("mm: hugetlb: replace hugetlb_free_vmemmap_enabled with a static_key"). As it introduced rlock(cpu_hotplug_lock) in dissolve_free_huge_page() code path while lock(pcp_batch_high_lock) is already in the __page_handle_poison(). [linmiaohe@huawei.com: extend comment per Oscar] [akpm@linux-foundation.org: reflow block comment] Link: https://lkml.kernel.org/r/20240407085456.2798193-1-linmiaohe@huawei.com Fixes: a6b4085 ("mm: hugetlb: replace hugetlb_free_vmemmap_enabled with a static_key") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Acked-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Jane Chu <jane.chu@oracle.com> Cc: Naoya Horiguchi <nao.horiguchi@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 96fdd1f ] 9f74a3d ("ice: Fix VF Reset paths when interface in a failed over aggregate"), the ice driver has acquired the LAG mutex in ice_reset_vf(). The commit placed this lock acquisition just prior to the acquisition of the VF configuration lock. If ice_reset_vf() acquires the configuration lock via the ICE_VF_RESET_LOCK flag, this could deadlock with ice_vc_cfg_qs_msg() because it always acquires the locks in the order of the VF configuration lock and then the LAG mutex. Lockdep reports this violation almost immediately on creating and then removing 2 VF: ====================================================== WARNING: possible circular locking dependency detected 6.8.0-rc6 openbmc#54 Tainted: G W O ------------------------------------------------------ kworker/60:3/6771 is trying to acquire lock: ff40d43e099380a0 (&vf->cfg_lock){+.+.}-{3:3}, at: ice_reset_vf+0x22f/0x4d0 [ice] but task is already holding lock: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&pf->lag_mutex){+.+.}-{3:3}: __lock_acquire+0x4f8/0xb40 lock_acquire+0xd4/0x2d0 __mutex_lock+0x9b/0xbf0 ice_vc_cfg_qs_msg+0x45/0x690 [ice] ice_vc_process_vf_msg+0x4f5/0x870 [ice] __ice_clean_ctrlq+0x2b5/0x600 [ice] ice_service_task+0x2c9/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 kthread+0x104/0x140 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1b/0x30 -> #0 (&vf->cfg_lock){+.+.}-{3:3}: check_prev_add+0xe2/0xc50 validate_chain+0x558/0x800 __lock_acquire+0x4f8/0xb40 lock_acquire+0xd4/0x2d0 __mutex_lock+0x9b/0xbf0 ice_reset_vf+0x22f/0x4d0 [ice] ice_process_vflr_event+0x98/0xd0 [ice] ice_service_task+0x1cc/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 kthread+0x104/0x140 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1b/0x30 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&pf->lag_mutex); lock(&vf->cfg_lock); lock(&pf->lag_mutex); lock(&vf->cfg_lock); *** DEADLOCK *** 4 locks held by kworker/60:3/6771: #0: ff40d43e05428b38 ((wq_completion)ice){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0 #1: ff50d06e05197e58 ((work_completion)(&pf->serv_task)){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0 #2: ff40d43ea1960e50 (&pf->vfs.table_lock){+.+.}-{3:3}, at: ice_process_vflr_event+0x48/0xd0 [ice] #3: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice] stack backtrace: CPU: 60 PID: 6771 Comm: kworker/60:3 Tainted: G W O 6.8.0-rc6 openbmc#54 Hardware name: Workqueue: ice ice_service_task [ice] Call Trace: <TASK> dump_stack_lvl+0x4a/0x80 check_noncircular+0x12d/0x150 check_prev_add+0xe2/0xc50 ? save_trace+0x59/0x230 ? add_chain_cache+0x109/0x450 validate_chain+0x558/0x800 __lock_acquire+0x4f8/0xb40 ? lockdep_hardirqs_on+0x7d/0x100 lock_acquire+0xd4/0x2d0 ? ice_reset_vf+0x22f/0x4d0 [ice] ? lock_is_held_type+0xc7/0x120 __mutex_lock+0x9b/0xbf0 ? ice_reset_vf+0x22f/0x4d0 [ice] ? ice_reset_vf+0x22f/0x4d0 [ice] ? rcu_is_watching+0x11/0x50 ? ice_reset_vf+0x22f/0x4d0 [ice] ice_reset_vf+0x22f/0x4d0 [ice] ? process_one_work+0x176/0x4d0 ice_process_vflr_event+0x98/0xd0 [ice] ice_service_task+0x1cc/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0x104/0x140 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> To avoid deadlock, we must acquire the LAG mutex only after acquiring the VF configuration lock. Fix the ice_reset_vf() to acquire the LAG mutex only after we either acquire or check that the VF configuration lock is held. Fixes: 9f74a3d ("ice: Fix VF Reset paths when interface in a failed over aggregate") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Dave Ertman <david.m.ertman@intel.com> Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240423182723.740401-5-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

…io() commit 52ccdde upstream. When I did memory failure tests recently, below warning occurs: DEBUG_LOCKS_WARN_ON(1) WARNING: CPU: 8 PID: 1011 at kernel/locking/lockdep.c:232 __lock_acquire+0xccb/0x1ca0 Modules linked in: mce_inject hwpoison_inject CPU: 8 PID: 1011 Comm: bash Kdump: loaded Not tainted 6.9.0-rc3-next-20240410-00012-gdb69f219f4be #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 RIP: 0010:__lock_acquire+0xccb/0x1ca0 RSP: 0018:ffffa7a1c7fe3bd0 EFLAGS: 00000082 RAX: 0000000000000000 RBX: eb851eb853975fcf RCX: ffffa1ce5fc1c9c8 RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffffa1ce5fc1c9c0 RBP: ffffa1c6865d3280 R08: ffffffffb0f570a8 R09: 0000000000009ffb R10: 0000000000000286 R11: ffffffffb0f2ad50 R12: ffffa1c6865d3d10 R13: ffffa1c6865d3c70 R14: 0000000000000000 R15: 0000000000000004 FS: 00007ff9f32aa740(0000) GS:ffffa1ce5fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ff9f3134ba0 CR3: 00000008484e4000 CR4: 00000000000006f0 Call Trace: <TASK> lock_acquire+0xbe/0x2d0 _raw_spin_lock_irqsave+0x3a/0x60 hugepage_subpool_put_pages.part.0+0xe/0xc0 free_huge_folio+0x253/0x3f0 dissolve_free_huge_page+0x147/0x210 __page_handle_poison+0x9/0x70 memory_failure+0x4e6/0x8c0 hard_offline_page_store+0x55/0xa0 kernfs_fop_write_iter+0x12c/0x1d0 vfs_write+0x380/0x540 ksys_write+0x64/0xe0 do_syscall_64+0xbc/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7ff9f3114887 RSP: 002b:00007ffecbacb458 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007ff9f3114887 RDX: 000000000000000c RSI: 0000564494164e10 RDI: 0000000000000001 RBP: 0000564494164e10 R08: 00007ff9f31d1460 R09: 000000007fffffff R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000000c R13: 00007ff9f321b780 R14: 00007ff9f3217600 R15: 00007ff9f3216a00 </TASK> Kernel panic - not syncing: kernel: panic_on_warn set ... CPU: 8 PID: 1011 Comm: bash Kdump: loaded Not tainted 6.9.0-rc3-next-20240410-00012-gdb69f219f4be #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> panic+0x326/0x350 check_panic_on_warn+0x4f/0x50 __warn+0x98/0x190 report_bug+0x18e/0x1a0 handle_bug+0x3d/0x70 exc_invalid_op+0x18/0x70 asm_exc_invalid_op+0x1a/0x20 RIP: 0010:__lock_acquire+0xccb/0x1ca0 RSP: 0018:ffffa7a1c7fe3bd0 EFLAGS: 00000082 RAX: 0000000000000000 RBX: eb851eb853975fcf RCX: ffffa1ce5fc1c9c8 RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffffa1ce5fc1c9c0 RBP: ffffa1c6865d3280 R08: ffffffffb0f570a8 R09: 0000000000009ffb R10: 0000000000000286 R11: ffffffffb0f2ad50 R12: ffffa1c6865d3d10 R13: ffffa1c6865d3c70 R14: 0000000000000000 R15: 0000000000000004 lock_acquire+0xbe/0x2d0 _raw_spin_lock_irqsave+0x3a/0x60 hugepage_subpool_put_pages.part.0+0xe/0xc0 free_huge_folio+0x253/0x3f0 dissolve_free_huge_page+0x147/0x210 __page_handle_poison+0x9/0x70 memory_failure+0x4e6/0x8c0 hard_offline_page_store+0x55/0xa0 kernfs_fop_write_iter+0x12c/0x1d0 vfs_write+0x380/0x540 ksys_write+0x64/0xe0 do_syscall_64+0xbc/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7ff9f3114887 RSP: 002b:00007ffecbacb458 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007ff9f3114887 RDX: 000000000000000c RSI: 0000564494164e10 RDI: 0000000000000001 RBP: 0000564494164e10 R08: 00007ff9f31d1460 R09: 000000007fffffff R10: 0000000000000000 R11: 0000000000000246 R12: 000000000000000c R13: 00007ff9f321b780 R14: 00007ff9f3217600 R15: 00007ff9f3216a00 </TASK> After git bisecting and digging into the code, I believe the root cause is that _deferred_list field of folio is unioned with _hugetlb_subpool field. In __update_and_free_hugetlb_folio(), folio->_deferred_list is initialized leading to corrupted folio->_hugetlb_subpool when folio is hugetlb. Later free_huge_folio() will use _hugetlb_subpool and above warning happens. But it is assumed hugetlb flag must have been cleared when calling folio_put() in update_and_free_hugetlb_folio(). This assumption is broken due to below race: CPU1 CPU2 dissolve_free_huge_page update_and_free_pages_bulk update_and_free_hugetlb_folio hugetlb_vmemmap_restore_folios folio_clear_hugetlb_vmemmap_optimized clear_flag = folio_test_hugetlb_vmemmap_optimized if (clear_flag) <-- False, it's already cleared. __folio_clear_hugetlb(folio) <-- Hugetlb is not cleared. folio_put free_huge_folio <-- free_the_page is expected. list_for_each_entry() __folio_clear_hugetlb <-- Too late. Fix this issue by checking whether folio is hugetlb directly instead of checking clear_flag to close the race window. Link: https://lkml.kernel.org/r/20240419085819.1901645-1-linmiaohe@huawei.com Fixes: 32c8771 ("hugetlb: do not clear hugetlb dtor until allocating vmemmap") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the new mode (called as mode#3) to monitor speed and control the PWM. Initialize mode #3 by default (fan tach input enable and PWM mode enable). We can reconfigure again by the pwm_enale setting. Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>

[ Upstream commit c3a5e3e ] When using cachefiles, lockdep may emit something similar to the circular locking dependency notice below. The problem appears to stem from the following: (1) Cachefiles manipulates xattrs on the files in its cache when called from ->writepages(). (2) The setxattr() and removexattr() system call handlers get the name (and value) from userspace after taking the sb_writers lock, putting accesses of the vma->vm_lock and mm->mmap_lock inside of that. (3) The afs filesystem uses a per-inode lock to prevent multiple revalidation RPCs and in writeback vs truncate to prevent parallel operations from deadlocking against the server on one side and local page locks on the other. Fix this by moving the getting of the name and value in {get,remove}xattr() outside of the sb_writers lock. This also has the minor benefits that we don't need to reget these in the event of a retry and we never try to take the sb_writers lock in the event we can't pull the name and value into the kernel. Alternative approaches that might fix this include moving the dispatch of a write to the cache off to a workqueue or trying to do without the validation lock in afs. Note that this might also affect other filesystems that use netfslib and/or cachefiles. ====================================================== WARNING: possible circular locking dependency detected 6.10.0-build2+ torvalds#956 Not tainted ------------------------------------------------------ fsstress/6050 is trying to acquire lock: ffff888138fd82f0 (mapping.invalidate_lock#3){++++}-{3:3}, at: filemap_fault+0x26e/0x8b0 but task is already holding lock: ffff888113f26d18 (&vma->vm_lock->lock){++++}-{3:3}, at: lock_vma_under_rcu+0x165/0x250 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #4 (&vma->vm_lock->lock){++++}-{3:3}: __lock_acquire+0xaf0/0xd80 lock_acquire.part.0+0x103/0x280 down_write+0x3b/0x50 vma_start_write+0x6b/0xa0 vma_link+0xcc/0x140 insert_vm_struct+0xb7/0xf0 alloc_bprm+0x2c1/0x390 kernel_execve+0x65/0x1a0 call_usermodehelper_exec_async+0x14d/0x190 ret_from_fork+0x24/0x40 ret_from_fork_asm+0x1a/0x30 -> #3 (&mm->mmap_lock){++++}-{3:3}: __lock_acquire+0xaf0/0xd80 lock_acquire.part.0+0x103/0x280 __might_fault+0x7c/0xb0 strncpy_from_user+0x25/0x160 removexattr+0x7f/0x100 __do_sys_fremovexattr+0x7e/0xb0 do_syscall_64+0x9f/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #2 (sb_writers#14){.+.+}-{0:0}: __lock_acquire+0xaf0/0xd80 lock_acquire.part.0+0x103/0x280 percpu_down_read+0x3c/0x90 vfs_iocb_iter_write+0xe9/0x1d0 __cachefiles_write+0x367/0x430 cachefiles_issue_write+0x299/0x2f0 netfs_advance_write+0x117/0x140 netfs_write_folio.isra.0+0x5ca/0x6e0 netfs_writepages+0x230/0x2f0 afs_writepages+0x4d/0x70 do_writepages+0x1e8/0x3e0 filemap_fdatawrite_wbc+0x84/0xa0 __filemap_fdatawrite_range+0xa8/0xf0 file_write_and_wait_range+0x59/0x90 afs_release+0x10f/0x270 __fput+0x25f/0x3d0 __do_sys_close+0x43/0x70 do_syscall_64+0x9f/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #1 (&vnode->validate_lock){++++}-{3:3}: __lock_acquire+0xaf0/0xd80 lock_acquire.part.0+0x103/0x280 down_read+0x95/0x200 afs_writepages+0x37/0x70 do_writepages+0x1e8/0x3e0 filemap_fdatawrite_wbc+0x84/0xa0 filemap_invalidate_inode+0x167/0x1e0 netfs_unbuffered_write_iter+0x1bd/0x2d0 vfs_write+0x22e/0x320 ksys_write+0xbc/0x130 do_syscall_64+0x9f/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #0 (mapping.invalidate_lock#3){++++}-{3:3}: check_noncircular+0x119/0x160 check_prev_add+0x195/0x430 __lock_acquire+0xaf0/0xd80 lock_acquire.part.0+0x103/0x280 down_read+0x95/0x200 filemap_fault+0x26e/0x8b0 __do_fault+0x57/0xd0 do_pte_missing+0x23b/0x320 __handle_mm_fault+0x2d4/0x320 handle_mm_fault+0x14f/0x260 do_user_addr_fault+0x2a2/0x500 exc_page_fault+0x71/0x90 asm_exc_page_fault+0x22/0x30 other info that might help us debug this: Chain exists of: mapping.invalidate_lock#3 --> &mm->mmap_lock --> &vma->vm_lock->lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- rlock(&vma->vm_lock->lock); lock(&mm->mmap_lock); lock(&vma->vm_lock->lock); rlock(mapping.invalidate_lock#3); *** DEADLOCK *** 1 lock held by fsstress/6050: #0: ffff888113f26d18 (&vma->vm_lock->lock){++++}-{3:3}, at: lock_vma_under_rcu+0x165/0x250 stack backtrace: CPU: 0 PID: 6050 Comm: fsstress Not tainted 6.10.0-build2+ torvalds#956 Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014 Call Trace: <TASK> dump_stack_lvl+0x57/0x80 check_noncircular+0x119/0x160 ? queued_spin_lock_slowpath+0x4be/0x510 ? __pfx_check_noncircular+0x10/0x10 ? __pfx_queued_spin_lock_slowpath+0x10/0x10 ? mark_lock+0x47/0x160 ? init_chain_block+0x9c/0xc0 ? add_chain_block+0x84/0xf0 check_prev_add+0x195/0x430 __lock_acquire+0xaf0/0xd80 ? __pfx___lock_acquire+0x10/0x10 ? __lock_release.isra.0+0x13b/0x230 lock_acquire.part.0+0x103/0x280 ? filemap_fault+0x26e/0x8b0 ? __pfx_lock_acquire.part.0+0x10/0x10 ? rcu_is_watching+0x34/0x60 ? lock_acquire+0xd7/0x120 down_read+0x95/0x200 ? filemap_fault+0x26e/0x8b0 ? __pfx_down_read+0x10/0x10 ? __filemap_get_folio+0x25/0x1a0 filemap_fault+0x26e/0x8b0 ? __pfx_filemap_fault+0x10/0x10 ? find_held_lock+0x7c/0x90 ? __pfx___lock_release.isra.0+0x10/0x10 ? __pte_offset_map+0x99/0x110 __do_fault+0x57/0xd0 do_pte_missing+0x23b/0x320 __handle_mm_fault+0x2d4/0x320 ? __pfx___handle_mm_fault+0x10/0x10 handle_mm_fault+0x14f/0x260 do_user_addr_fault+0x2a2/0x500 exc_page_fault+0x71/0x90 asm_exc_page_fault+0x22/0x30 Signed-off-by: David Howells <dhowells@redhat.com> Link: https://lore.kernel.org/r/2136178.1721725194@warthog.procyon.org.uk cc: Alexander Viro <viro@zeniv.linux.org.uk> cc: Christian Brauner <brauner@kernel.org> cc: Jan Kara <jack@suse.cz> cc: Jeff Layton <jlayton@kernel.org> cc: Gao Xiang <xiang@kernel.org> cc: Matthew Wilcox <willy@infradead.org> cc: netfs@lists.linux.dev cc: linux-erofs@lists.ozlabs.org cc: linux-fsdevel@vger.kernel.org [brauner: fix minor issues] Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1403c8b ] When ib_cache_update return an error, we exit ib_cache_setup_one instantly with no proper cleanup, even though before this we had already successfully done gid_table_setup_one, that results in the kernel WARN below. Do proper cleanup using gid_table_cleanup_one before returning the err in order to fix the issue. WARNING: CPU: 4 PID: 922 at drivers/infiniband/core/cache.c:806 gid_table_release_one+0x181/0x1a0 Modules linked in: CPU: 4 UID: 0 PID: 922 Comm: c_repro Not tainted 6.11.0-rc1+ #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:gid_table_release_one+0x181/0x1a0 Code: 44 8b 38 75 0c e8 2f cb 34 ff 4d 8b b5 28 05 00 00 e8 23 cb 34 ff 44 89 f9 89 da 4c 89 f6 48 c7 c7 d0 58 14 83 e8 4f de 21 ff <0f> 0b 4c 8b 75 30 e9 54 ff ff ff 48 8 3 c4 10 5b 5d 41 5c 41 5d 41 RSP: 0018:ffffc90002b835b0 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff811c8527 RDX: 0000000000000000 RSI: ffffffff811c8534 RDI: 0000000000000001 RBP: ffff8881011b3d00 R08: ffff88810b3abe00 R09: 205d303839303631 R10: 666572207972746e R11: 72746e6520444947 R12: 0000000000000001 R13: ffff888106390000 R14: ffff8881011f2110 R15: 0000000000000001 FS: 00007fecc3b70800(0000) GS:ffff88813bd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000340 CR3: 000000010435a001 CR4: 00000000003706b0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? show_regs+0x94/0xa0 ? __warn+0x9e/0x1c0 ? gid_table_release_one+0x181/0x1a0 ? report_bug+0x1f9/0x340 ? gid_table_release_one+0x181/0x1a0 ? handle_bug+0xa2/0x110 ? exc_invalid_op+0x31/0xa0 ? asm_exc_invalid_op+0x16/0x20 ? __warn_printk+0xc7/0x180 ? __warn_printk+0xd4/0x180 ? gid_table_release_one+0x181/0x1a0 ib_device_release+0x71/0xe0 ? __pfx_ib_device_release+0x10/0x10 device_release+0x44/0xd0 kobject_put+0x135/0x3d0 put_device+0x20/0x30 rxe_net_add+0x7d/0xa0 rxe_newlink+0xd7/0x190 nldev_newlink+0x1b0/0x2a0 ? __pfx_nldev_newlink+0x10/0x10 rdma_nl_rcv_msg+0x1ad/0x2e0 rdma_nl_rcv_skb.constprop.0+0x176/0x210 netlink_unicast+0x2de/0x400 netlink_sendmsg+0x306/0x660 __sock_sendmsg+0x110/0x120 ____sys_sendmsg+0x30e/0x390 ___sys_sendmsg+0x9b/0xf0 ? kstrtouint+0x6e/0xa0 ? kstrtouint_from_user+0x7c/0xb0 ? get_pid_task+0xb0/0xd0 ? proc_fail_nth_write+0x5b/0x140 ? __fget_light+0x9a/0x200 ? preempt_count_add+0x47/0xa0 __sys_sendmsg+0x61/0xd0 do_syscall_64+0x50/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e Fixes: 1901b91 ("IB/core: Fix potential NULL pointer dereference in pkey cache") Signed-off-by: Patrisious Haddad <phaddad@nvidia.com> Reviewed-by: Maher Sanalla <msanalla@nvidia.com> Link: https://patch.msgid.link/79137687d829899b0b1c9835fcb4b258004c439a.1725273354.git.leon@kernel.org Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 44d1745 upstream. Use a dedicated mutex to guard kvm_usage_count to fix a potential deadlock on x86 due to a chain of locks and SRCU synchronizations. Translating the below lockdep splat, CPU1 openbmc#6 will wait on CPU0 #1, CPU0 openbmc#8 will wait on CPU2 #3, and CPU2 openbmc#7 will wait on CPU1 #4 (if there's a writer, due to the fairness of r/w semaphores). CPU0 CPU1 CPU2 1 lock(&kvm->slots_lock); 2 lock(&vcpu->mutex); 3 lock(&kvm->srcu); 4 lock(cpu_hotplug_lock); 5 lock(kvm_lock); 6 lock(&kvm->slots_lock); 7 lock(cpu_hotplug_lock); 8 sync(&kvm->srcu); Note, there are likely more potential deadlocks in KVM x86, e.g. the same pattern of taking cpu_hotplug_lock outside of kvm_lock likely exists with __kvmclock_cpufreq_notifier(): cpuhp_cpufreq_online() | -> cpufreq_online() | -> cpufreq_gov_performance_limits() | -> __cpufreq_driver_target() | -> __target_index() | -> cpufreq_freq_transition_begin() | -> cpufreq_notify_transition() | -> ... __kvmclock_cpufreq_notifier() But, actually triggering such deadlocks is beyond rare due to the combination of dependencies and timings involved. E.g. the cpufreq notifier is only used on older CPUs without a constant TSC, mucking with the NX hugepage mitigation while VMs are running is very uncommon, and doing so while also onlining/offlining a CPU (necessary to generate contention on cpu_hotplug_lock) would be even more unusual. The most robust solution to the general cpu_hotplug_lock issue is likely to switch vm_list to be an RCU-protected list, e.g. so that x86's cpufreq notifier doesn't to take kvm_lock. For now, settle for fixing the most blatant deadlock, as switching to an RCU-protected list is a much more involved change, but add a comment in locking.rst to call out that care needs to be taken when walking holding kvm_lock and walking vm_list. ====================================================== WARNING: possible circular locking dependency detected 6.10.0-smp--c257535a0c9d-pip torvalds#330 Tainted: G S O ------------------------------------------------------ tee/35048 is trying to acquire lock: ff6a80eced71e0a8 (&kvm->slots_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x179/0x1e0 [kvm] but task is already holding lock: ffffffffc07abb08 (kvm_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x14a/0x1e0 [kvm] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kvm_lock){+.+.}-{3:3}: __mutex_lock+0x6a/0xb40 mutex_lock_nested+0x1f/0x30 kvm_dev_ioctl+0x4fb/0xe50 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #2 (cpu_hotplug_lock){++++}-{0:0}: cpus_read_lock+0x2e/0xb0 static_key_slow_inc+0x16/0x30 kvm_lapic_set_base+0x6a/0x1c0 [kvm] kvm_set_apic_base+0x8f/0xe0 [kvm] kvm_set_msr_common+0x9ae/0xf80 [kvm] vmx_set_msr+0xa54/0xbe0 [kvm_intel] __kvm_set_msr+0xb6/0x1a0 [kvm] kvm_arch_vcpu_ioctl+0xeca/0x10c0 [kvm] kvm_vcpu_ioctl+0x485/0x5b0 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #1 (&kvm->srcu){.+.+}-{0:0}: __synchronize_srcu+0x44/0x1a0 synchronize_srcu_expedited+0x21/0x30 kvm_swap_active_memslots+0x110/0x1c0 [kvm] kvm_set_memslot+0x360/0x620 [kvm] __kvm_set_memory_region+0x27b/0x300 [kvm] kvm_vm_ioctl_set_memory_region+0x43/0x60 [kvm] kvm_vm_ioctl+0x295/0x650 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #0 (&kvm->slots_lock){+.+.}-{3:3}: __lock_acquire+0x15ef/0x2e30 lock_acquire+0xe0/0x260 __mutex_lock+0x6a/0xb40 mutex_lock_nested+0x1f/0x30 set_nx_huge_pages+0x179/0x1e0 [kvm] param_attr_store+0x93/0x100 module_attr_store+0x22/0x40 sysfs_kf_write+0x81/0xb0 kernfs_fop_write_iter+0x133/0x1d0 vfs_write+0x28d/0x380 ksys_write+0x70/0xe0 __x64_sys_write+0x1f/0x30 x64_sys_call+0x281b/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e Cc: Chao Gao <chao.gao@intel.com> Fixes: 0bf5049 ("KVM: Drop kvm_count_lock and instead protect kvm_usage_count with kvm_lock") Cc: stable@vger.kernel.org Reviewed-by: Kai Huang <kai.huang@intel.com> Acked-by: Kai Huang <kai.huang@intel.com> Tested-by: Farrah Chen <farrah.chen@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Message-ID: <20240830043600.127750-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the new mode (called as mode#3) to monitor speed and control the PWM. Initialize mode #3 by default (fan tach input enable and PWM mode enable). We can reconfigure again by the pwm_enale setting. Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>

commit ac01c8c upstream. AddressSanitizer found a use-after-free bug in the symbol code which manifested as 'perf top' segfaulting. ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80 READ of size 1 at 0x60b00c48844b thread T193 #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310 #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286 #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614 #3 0x5650d804568f in __hists__add_entry util/hist.c:754 #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772 openbmc#5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997 openbmc#6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242 openbmc#7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845 openbmc#8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208 openbmc#9 0x5650d7fdb51b in do_flush util/ordered-events.c:245 openbmc#10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324 openbmc#11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120 openbmc#12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442 openbmc#13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81 When updating hist maps it's also necessary to update the hist symbol reference because the old one gets freed in map__put(). While this bug was probably introduced with 5c24b67 ("perf tools: Replace map->referenced & maps->removed_maps with map->refcnt"), the symbol objects were leaked until c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so the bug was masked. Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") Reported-by: Yunzhao Li <yunzhao@cloudflare.com> Signed-off-by: Matt Fleming (Cloudflare) <matt@readmodwrite.com> Cc: Ian Rogers <irogers@google.com> Cc: kernel-team@cloudflare.com Cc: Namhyung Kim <namhyung@kernel.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: stable@vger.kernel.org # v5.13+ Link: https://lore.kernel.org/r/20240815142212.3834625-1-matt@readmodwrite.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 openbmc#5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 openbmc#6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 openbmc#7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 openbmc#8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 openbmc#9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 openbmc#10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 openbmc#11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 openbmc#12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 openbmc#13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 openbmc#14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 openbmc#15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 openbmc#16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 openbmc#17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Matt Fleming <matt@readmodwrite.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20240826221045.1202305-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…tion to perf_sched__replay() [ Upstream commit c690786 ] The start_work_mutex and work_done_wait_mutex are used only for the 'perf sched replay'. Put their initialization in perf_sched__replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.197 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 14.952 MB perf.data (134165 samples) ] # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 65658 nsecs the run test took 999991 nsecs the sleep test took 1079324 nsecs nr_run_events: 42378 nr_sleep_events: 43102 nr_wakeup_events: 31852 target-less wakeups: 17 multi-target wakeups: 712 task 0 ( swapper: 0), nr_events: 10451 task 1 ( swapper: 1), nr_events: 3 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 717 ( sched-messaging: 74483), nr_events: 152 task 718 ( sched-messaging: 74484), nr_events: 1944 task 719 ( sched-messaging: 74485), nr_events: 73 task 720 ( sched-messaging: 74486), nr_events: 163 task 721 ( sched-messaging: 74487), nr_events: 942 task 722 ( sched-messaging: 74488), nr_events: 78 task 723 ( sched-messaging: 74489), nr_events: 1090 ------------------------------------------------------------ #1 : 1366.507, ravg: 1366.51, cpu: 7682.70 / 7682.70 #2 : 1410.072, ravg: 1370.86, cpu: 7723.88 / 7686.82 #3 : 1396.296, ravg: 1373.41, cpu: 7568.20 / 7674.96 #4 : 1381.019, ravg: 1374.17, cpu: 7531.81 / 7660.64 openbmc#5 : 1393.826, ravg: 1376.13, cpu: 7725.25 / 7667.11 openbmc#6 : 1401.581, ravg: 1378.68, cpu: 7594.82 / 7659.88 openbmc#7 : 1381.337, ravg: 1378.94, cpu: 7371.22 / 7631.01 openbmc#8 : 1373.842, ravg: 1378.43, cpu: 7894.92 / 7657.40 openbmc#9 : 1364.697, ravg: 1377.06, cpu: 7324.91 / 7624.15 openbmc#10 : 1363.613, ravg: 1375.72, cpu: 7209.55 / 7582.69 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-2-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

…f_sched__{lat|map|replay}() [ Upstream commit bd2cdf2 ] The curr_pid and cpu_last_switched are used only for the 'perf sched replay/latency/map'. Put their initialization in perf_sched__{lat|map|replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.209 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 16.456 MB perf.data (147907 samples) ] # perf sched lat ------------------------------------------------------------------------------------------------------------------------------------------- Task | Runtime ms | Switches | Avg delay ms | Max delay ms | Max delay start | Max delay end | ------------------------------------------------------------------------------------------------------------------------------------------- sched-messaging:(401) | 2990.699 ms | 38705 | avg: 0.661 ms | max: 67.046 ms | max start: 456532.624830 s | max end: 456532.691876 s qemu-system-x86:(7) | 179.764 ms | 2191 | avg: 0.152 ms | max: 21.857 ms | max start: 456532.576434 s | max end: 456532.598291 s sshd:48125 | 0.522 ms | 2 | avg: 0.037 ms | max: 0.046 ms | max start: 456532.514610 s | max end: 456532.514656 s <SNIP> ksoftirqd/11:82 | 0.063 ms | 1 | avg: 0.005 ms | max: 0.005 ms | max start: 456532.769366 s | max end: 456532.769371 s kworker/9:0-mm_:34624 | 0.233 ms | 20 | avg: 0.004 ms | max: 0.007 ms | max start: 456532.690804 s | max end: 456532.690812 s migration/13:93 | 0.000 ms | 1 | avg: 0.004 ms | max: 0.004 ms | max start: 456532.512669 s | max end: 456532.512674 s ----------------------------------------------------------------------------------------------------------------- TOTAL: | 3180.750 ms | 41368 | --------------------------------------------------- # echo $? 0 # perf sched map *A0 456532.510141 secs A0 => migration/0:15 *. 456532.510171 secs . => swapper:0 . *B0 456532.510261 secs B0 => migration/1:21 . *. 456532.510279 secs <SNIP> L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . . 456532.785979 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . 456532.786054 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . 456532.786127 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . 456532.786197 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 456532.786270 secs # echo $? 0 # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 66473 nsecs the run test took 1000002 nsecs the sleep test took 1082686 nsecs nr_run_events: 49334 nr_sleep_events: 50054 nr_wakeup_events: 34701 target-less wakeups: 165 multi-target wakeups: 766 task 0 ( swapper: 0), nr_events: 15419 task 1 ( swapper: 1), nr_events: 1 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 715 ( sched-messaging: 110248), nr_events: 1438 task 716 ( sched-messaging: 110249), nr_events: 512 task 717 ( sched-messaging: 110250), nr_events: 500 task 718 ( sched-messaging: 110251), nr_events: 537 task 719 ( sched-messaging: 110252), nr_events: 823 ------------------------------------------------------------ #1 : 1325.288, ravg: 1325.29, cpu: 7823.35 / 7823.35 #2 : 1363.606, ravg: 1329.12, cpu: 7655.53 / 7806.56 #3 : 1349.494, ravg: 1331.16, cpu: 7544.80 / 7780.39 #4 : 1311.488, ravg: 1329.19, cpu: 7495.13 / 7751.86 openbmc#5 : 1309.902, ravg: 1327.26, cpu: 7266.65 / 7703.34 openbmc#6 : 1309.535, ravg: 1325.49, cpu: 7843.86 / 7717.39 openbmc#7 : 1316.482, ravg: 1324.59, cpu: 7854.41 / 7731.09 openbmc#8 : 1366.604, ravg: 1328.79, cpu: 7955.81 / 7753.57 openbmc#9 : 1326.286, ravg: 1328.54, cpu: 7466.86 / 7724.90 openbmc#10 : 1356.653, ravg: 1331.35, cpu: 7566.60 / 7709.07 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-5-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d1bc560 ] Add nested locking with I_MUTEX_XATTR subclass to avoid lockdep warning while handling xattr inode on file open syscall at ext4_xattr_inode_iget. Backtrace EXT4-fs (loop0): Ignoring removed oldalloc option ====================================================== WARNING: possible circular locking dependency detected 5.10.0-syzkaller #0 Not tainted ------------------------------------------------------ syz-executor543/2794 is trying to acquire lock: ffff8880215e1a48 (&ea_inode->i_rwsem#7/1){+.+.}-{3:3}, at: inode_lock include/linux/fs.h:782 [inline] ffff8880215e1a48 (&ea_inode->i_rwsem#7/1){+.+.}-{3:3}, at: ext4_xattr_inode_iget+0x42a/0x5c0 fs/ext4/xattr.c:425 but task is already holding lock: ffff8880215e3278 (&ei->i_data_sem/3){++++}-{3:3}, at: ext4_setattr+0x136d/0x19c0 fs/ext4/inode.c:5559 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&ei->i_data_sem/3){++++}-{3:3}: lock_acquire+0x197/0x480 kernel/locking/lockdep.c:5566 down_write+0x93/0x180 kernel/locking/rwsem.c:1564 ext4_update_i_disksize fs/ext4/ext4.h:3267 [inline] ext4_xattr_inode_write fs/ext4/xattr.c:1390 [inline] ext4_xattr_inode_lookup_create fs/ext4/xattr.c:1538 [inline] ext4_xattr_set_entry+0x331a/0x3d80 fs/ext4/xattr.c:1662 ext4_xattr_ibody_set+0x124/0x390 fs/ext4/xattr.c:2228 ext4_xattr_set_handle+0xc27/0x14e0 fs/ext4/xattr.c:2385 ext4_xattr_set+0x219/0x390 fs/ext4/xattr.c:2498 ext4_xattr_user_set+0xc9/0xf0 fs/ext4/xattr_user.c:40 __vfs_setxattr+0x404/0x450 fs/xattr.c:177 __vfs_setxattr_noperm+0x11d/0x4f0 fs/xattr.c:208 __vfs_setxattr_locked+0x1f9/0x210 fs/xattr.c:266 vfs_setxattr+0x112/0x2c0 fs/xattr.c:283 setxattr+0x1db/0x3e0 fs/xattr.c:548 path_setxattr+0x15a/0x240 fs/xattr.c:567 __do_sys_setxattr fs/xattr.c:582 [inline] __se_sys_setxattr fs/xattr.c:578 [inline] __x64_sys_setxattr+0xc5/0xe0 fs/xattr.c:578 do_syscall_64+0x6d/0xa0 arch/x86/entry/common.c:62 entry_SYSCALL_64_after_hwframe+0x61/0xcb -> #0 (&ea_inode->i_rwsem#7/1){+.+.}-{3:3}: check_prev_add kernel/locking/lockdep.c:2988 [inline] check_prevs_add kernel/locking/lockdep.c:3113 [inline] validate_chain+0x1695/0x58f0 kernel/locking/lockdep.c:3729 __lock_acquire+0x12fd/0x20d0 kernel/locking/lockdep.c:4955 lock_acquire+0x197/0x480 kernel/locking/lockdep.c:5566 down_write+0x93/0x180 kernel/locking/rwsem.c:1564 inode_lock include/linux/fs.h:782 [inline] ext4_xattr_inode_iget+0x42a/0x5c0 fs/ext4/xattr.c:425 ext4_xattr_inode_get+0x138/0x410 fs/ext4/xattr.c:485 ext4_xattr_move_to_block fs/ext4/xattr.c:2580 [inline] ext4_xattr_make_inode_space fs/ext4/xattr.c:2682 [inline] ext4_expand_extra_isize_ea+0xe70/0x1bb0 fs/ext4/xattr.c:2774 __ext4_expand_extra_isize+0x304/0x3f0 fs/ext4/inode.c:5898 ext4_try_to_expand_extra_isize fs/ext4/inode.c:5941 [inline] __ext4_mark_inode_dirty+0x591/0x810 fs/ext4/inode.c:6018 ext4_setattr+0x1400/0x19c0 fs/ext4/inode.c:5562 notify_change+0xbb6/0xe60 fs/attr.c:435 do_truncate+0x1de/0x2c0 fs/open.c:64 handle_truncate fs/namei.c:2970 [inline] do_open fs/namei.c:3311 [inline] path_openat+0x29f3/0x3290 fs/namei.c:3425 do_filp_open+0x20b/0x450 fs/namei.c:3452 do_sys_openat2+0x124/0x460 fs/open.c:1207 do_sys_open fs/open.c:1223 [inline] __do_sys_open fs/open.c:1231 [inline] __se_sys_open fs/open.c:1227 [inline] __x64_sys_open+0x221/0x270 fs/open.c:1227 do_syscall_64+0x6d/0xa0 arch/x86/entry/common.c:62 entry_SYSCALL_64_after_hwframe+0x61/0xcb other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&ei->i_data_sem/3); lock(&ea_inode->i_rwsem#7/1); lock(&ei->i_data_sem/3); lock(&ea_inode->i_rwsem#7/1); *** DEADLOCK *** 5 locks held by syz-executor543/2794: #0: ffff888026fbc448 (sb_writers#4){.+.+}-{0:0}, at: mnt_want_write+0x4a/0x2a0 fs/namespace.c:365 #1: ffff8880215e3488 (&sb->s_type->i_mutex_key#7){++++}-{3:3}, at: inode_lock include/linux/fs.h:782 [inline] #1: ffff8880215e3488 (&sb->s_type->i_mutex_key#7){++++}-{3:3}, at: do_truncate+0x1cf/0x2c0 fs/open.c:62 #2: ffff8880215e3310 (&ei->i_mmap_sem){++++}-{3:3}, at: ext4_setattr+0xec4/0x19c0 fs/ext4/inode.c:5519 #3: ffff8880215e3278 (&ei->i_data_sem/3){++++}-{3:3}, at: ext4_setattr+0x136d/0x19c0 fs/ext4/inode.c:5559 #4: ffff8880215e30c8 (&ei->xattr_sem){++++}-{3:3}, at: ext4_write_trylock_xattr fs/ext4/xattr.h:162 [inline] #4: ffff8880215e30c8 (&ei->xattr_sem){++++}-{3:3}, at: ext4_try_to_expand_extra_isize fs/ext4/inode.c:5938 [inline] #4: ffff8880215e30c8 (&ei->xattr_sem){++++}-{3:3}, at: __ext4_mark_inode_dirty+0x4fb/0x810 fs/ext4/inode.c:6018 stack backtrace: CPU: 1 PID: 2794 Comm: syz-executor543 Not tainted 5.10.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x177/0x211 lib/dump_stack.c:118 print_circular_bug+0x146/0x1b0 kernel/locking/lockdep.c:2002 check_noncircular+0x2cc/0x390 kernel/locking/lockdep.c:2123 check_prev_add kernel/locking/lockdep.c:2988 [inline] check_prevs_add kernel/locking/lockdep.c:3113 [inline] validate_chain+0x1695/0x58f0 kernel/locking/lockdep.c:3729 __lock_acquire+0x12fd/0x20d0 kernel/locking/lockdep.c:4955 lock_acquire+0x197/0x480 kernel/locking/lockdep.c:5566 down_write+0x93/0x180 kernel/locking/rwsem.c:1564 inode_lock include/linux/fs.h:782 [inline] ext4_xattr_inode_iget+0x42a/0x5c0 fs/ext4/xattr.c:425 ext4_xattr_inode_get+0x138/0x410 fs/ext4/xattr.c:485 ext4_xattr_move_to_block fs/ext4/xattr.c:2580 [inline] ext4_xattr_make_inode_space fs/ext4/xattr.c:2682 [inline] ext4_expand_extra_isize_ea+0xe70/0x1bb0 fs/ext4/xattr.c:2774 __ext4_expand_extra_isize+0x304/0x3f0 fs/ext4/inode.c:5898 ext4_try_to_expand_extra_isize fs/ext4/inode.c:5941 [inline] __ext4_mark_inode_dirty+0x591/0x810 fs/ext4/inode.c:6018 ext4_setattr+0x1400/0x19c0 fs/ext4/inode.c:5562 notify_change+0xbb6/0xe60 fs/attr.c:435 do_truncate+0x1de/0x2c0 fs/open.c:64 handle_truncate fs/namei.c:2970 [inline] do_open fs/namei.c:3311 [inline] path_openat+0x29f3/0x3290 fs/namei.c:3425 do_filp_open+0x20b/0x450 fs/namei.c:3452 do_sys_openat2+0x124/0x460 fs/open.c:1207 do_sys_open fs/open.c:1223 [inline] __do_sys_open fs/open.c:1231 [inline] __se_sys_open fs/open.c:1227 [inline] __x64_sys_open+0x221/0x270 fs/open.c:1227 do_syscall_64+0x6d/0xa0 arch/x86/entry/common.c:62 entry_SYSCALL_64_after_hwframe+0x61/0xcb RIP: 0033:0x7f0cde4ea229 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 21 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd81d1c978 EFLAGS: 00000246 ORIG_RAX: 0000000000000002 RAX: ffffffffffffffda RBX: 0030656c69662f30 RCX: 00007f0cde4ea229 RDX: 0000000000000089 RSI: 00000000000a0a00 RDI: 00000000200001c0 RBP: 2f30656c69662f2e R08: 0000000000208000 R09: 0000000000208000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffd81d1c9c0 R13: 00007ffd81d1ca00 R14: 0000000000080000 R15: 0000000000000003 EXT4-fs error (device loop0): ext4_expand_extra_isize_ea:2730: inode openbmc#13: comm syz-executor543: corrupted in-inode xattr Signed-off-by: Wojciech Gładysz <wojciech.gladysz@infogain.com> Link: https://patch.msgid.link/20240801143827.19135-1-wojciech.gladysz@infogain.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a848c29 ] On the node of an NFS client, some files saved in the mountpoint of the NFS server were copied to another location of the same NFS server. Accidentally, the nfs42_complete_copies() got a NULL-pointer dereference crash with the following syslog: [232064.838881] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232064.839360] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232066.588183] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058 [232066.588586] Mem abort info: [232066.588701] ESR = 0x0000000096000007 [232066.588862] EC = 0x25: DABT (current EL), IL = 32 bits [232066.589084] SET = 0, FnV = 0 [232066.589216] EA = 0, S1PTW = 0 [232066.589340] FSC = 0x07: level 3 translation fault [232066.589559] Data abort info: [232066.589683] ISV = 0, ISS = 0x00000007 [232066.589842] CM = 0, WnR = 0 [232066.589967] user pgtable: 64k pages, 48-bit VAs, pgdp=00002000956ff400 [232066.590231] [0000000000000058] pgd=08001100ae100003, p4d=08001100ae100003, pud=08001100ae100003, pmd=08001100b3c00003, pte=0000000000000000 [232066.590757] Internal error: Oops: 96000007 [#1] SMP [232066.590958] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm vhost_net vhost vhost_iotlb tap tun ipt_rpfilter xt_multiport ip_set_hash_ip ip_set_hash_net xfrm_interface xfrm6_tunnel tunnel4 tunnel6 esp4 ah4 wireguard libcurve25519_generic veth xt_addrtype xt_set nf_conntrack_netlink ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_bitmap_port ip_set_hash_ipport dummy ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs iptable_filter sch_ingress nfnetlink_cttimeout vport_gre ip_gre ip_tunnel gre vport_geneve geneve vport_vxlan vxlan ip6_udp_tunnel udp_tunnel openvswitch nf_conncount dm_round_robin dm_service_time dm_multipath xt_nat xt_MASQUERADE nft_chain_nat nf_nat xt_mark xt_conntrack xt_comment nft_compat nft_counter nf_tables nfnetlink ocfs2 ocfs2_nodemanager ocfs2_stackglue iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ipmi_ssif nbd overlay 8021q garp mrp bonding tls rfkill sunrpc ext4 mbcache jbd2 [232066.591052] vfat fat cas_cache cas_disk ses enclosure scsi_transport_sas sg acpi_ipmi ipmi_si ipmi_devintf ipmi_msghandler ip_tables vfio_pci vfio_pci_core vfio_virqfd vfio_iommu_type1 vfio dm_mirror dm_region_hash dm_log dm_mod nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter bridge stp llc fuse xfs libcrc32c ast drm_vram_helper qla2xxx drm_kms_helper syscopyarea crct10dif_ce sysfillrect ghash_ce sysimgblt sha2_ce fb_sys_fops cec sha256_arm64 sha1_ce drm_ttm_helper ttm nvme_fc igb sbsa_gwdt nvme_fabrics drm nvme_core i2c_algo_bit i40e scsi_transport_fc megaraid_sas aes_neon_bs [232066.596953] CPU: 6 PID: 4124696 Comm: 10.253.166.125- Kdump: loaded Not tainted 5.15.131-9.cl9_ocfs2.aarch64 #1 [232066.597356] Hardware name: Great Wall .\x93\x8e...RF6260 V5/GWMSSE2GL1T, BIOS T656FBE_V3.0.18 2024-01-06 [232066.597721] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [232066.598034] pc : nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.598327] lr : nfs4_reclaim_open_state+0x12c/0x800 [nfsv4] [232066.598595] sp : ffff8000f568fc70 [232066.598731] x29: ffff8000f568fc70 x28: 0000000000001000 x27: ffff21003db33000 [232066.599030] x26: ffff800005521ae0 x25: ffff0100f98fa3f0 x24: 0000000000000001 [232066.599319] x23: ffff800009920008 x22: ffff21003db33040 x21: ffff21003db33050 [232066.599628] x20: ffff410172fe9e40 x19: ffff410172fe9e00 x18: 0000000000000000 [232066.599914] x17: 0000000000000000 x16: 0000000000000004 x15: 0000000000000000 [232066.600195] x14: 0000000000000000 x13: ffff800008e685a8 x12: 00000000eac0c6e6 [232066.600498] x11: 0000000000000000 x10: 0000000000000008 x9 : ffff8000054e5828 [232066.600784] x8 : 00000000ffffffbf x7 : 0000000000000001 x6 : 000000000a9eb14a [232066.601062] x5 : 0000000000000000 x4 : ffff70ff8a14a800 x3 : 0000000000000058 [232066.601348] x2 : 0000000000000001 x1 : 54dce46366daa6c6 x0 : 0000000000000000 [232066.601636] Call trace: [232066.601749] nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.601998] nfs4_do_reclaim+0x1b8/0x28c [nfsv4] [232066.602218] nfs4_state_manager+0x928/0x10f0 [nfsv4] [232066.602455] nfs4_run_state_manager+0x78/0x1b0 [nfsv4] [232066.602690] kthread+0x110/0x114 [232066.602830] ret_from_fork+0x10/0x20 [232066.602985] Code: 1400000d f9403f20 f9402e61 91016003 (f9402c00) [232066.603284] SMP: stopping secondary CPUs [232066.606936] Starting crashdump kernel... [232066.607146] Bye! Analysing the vmcore, we know that nfs4_copy_state listed by destination nfs_server->ss_copies was added by the field copies in handle_async_copy(), and we found a waiting copy process with the stack as: PID: 3511963 TASK: ffff710028b47e00 CPU: 0 COMMAND: "cp" #0 [ffff8001116ef740] __switch_to at ffff8000081b92f4 #1 [ffff8001116ef760] __schedule at ffff800008dd0650 #2 [ffff8001116ef7c0] schedule at ffff800008dd0a00 #3 [ffff8001116ef7e0] schedule_timeout at ffff800008dd6aa0 #4 [ffff8001116ef860] __wait_for_common at ffff800008dd166c openbmc#5 [ffff8001116ef8e0] wait_for_completion_interruptible at ffff800008dd1898 openbmc#6 [ffff8001116ef8f0] handle_async_copy at ffff8000055142f4 [nfsv4] openbmc#7 [ffff8001116ef970] _nfs42_proc_copy at ffff8000055147c8 [nfsv4] openbmc#8 [ffff8001116efa80] nfs42_proc_copy at ffff800005514cf0 [nfsv4] openbmc#9 [ffff8001116efc50] __nfs4_copy_file_range.constprop.0 at ffff8000054ed694 [nfsv4] The NULL-pointer dereference was due to nfs42_complete_copies() listed the nfs_server->ss_copies by the field ss_copies of nfs4_copy_state. So the nfs4_copy_state address ffff0100f98fa3f0 was offset by 0x10 and the data accessed through this pointer was also incorrect. Generally, the ordered list nfs4_state_owner->so_states indicate open(O_RDWR) or open(O_WRITE) states are reclaimed firstly by nfs4_reclaim_open_state(). When destination state reclaim is failed with NFS_STATE_RECOVERY_FAILED and copies are not deleted in nfs_server->ss_copies, the source state may be passed to the nfs42_complete_copies() process earlier, resulting in this crash scene finally. To solve this issue, we add a list_head nfs_server->ss_src_copies for a server-to-server copy specially. Fixes: 0e65a32 ("NFS: handle source server reboot") Signed-off-by: Yanjun Zhang <zhangyanjun@cestc.cn> Reviewed-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 3d04139 upstream. Syzkaller reported a lockdep splat: ============================================ WARNING: possible recursive locking detected 6.11.0-rc6-syzkaller-00019-g67784a74e258 #0 Not tainted -------------------------------------------- syz-executor364/5113 is trying to acquire lock: ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 but task is already holding lock: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(k-slock-AF_INET); lock(k-slock-AF_INET); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by syz-executor364/5113: #0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline] #0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0x153/0x1b10 net/mptcp/protocol.c:1806 #1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline] #1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg_fastopen+0x11f/0x530 net/mptcp/protocol.c:1727 #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x5f/0x1b80 net/ipv4/ip_output.c:470 #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x45f/0x1390 net/ipv4/ip_output.c:228 #4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: local_lock_acquire include/linux/local_lock_internal.h:29 [inline] #4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: process_backlog+0x33b/0x15b0 net/core/dev.c:6104 openbmc#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] openbmc#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] openbmc#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0x230/0x5f0 net/ipv4/ip_input.c:232 openbmc#6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] openbmc#6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 stack backtrace: CPU: 0 UID: 0 PID: 5113 Comm: syz-executor364 Not tainted 6.11.0-rc6-syzkaller-00019-g67784a74e258 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:93 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119 check_deadlock kernel/locking/lockdep.c:3061 [inline] validate_chain+0x15d3/0x5900 kernel/locking/lockdep.c:3855 __lock_acquire+0x137a/0x2040 kernel/locking/lockdep.c:5142 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5759 __raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline] _raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154 spin_lock include/linux/spinlock.h:351 [inline] sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 mptcp_sk_clone_init+0x32/0x13c0 net/mptcp/protocol.c:3279 subflow_syn_recv_sock+0x931/0x1920 net/mptcp/subflow.c:874 tcp_check_req+0xfe4/0x1a20 net/ipv4/tcp_minisocks.c:853 tcp_v4_rcv+0x1c3e/0x37f0 net/ipv4/tcp_ipv4.c:2267 ip_protocol_deliver_rcu+0x22e/0x440 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x341/0x5f0 net/ipv4/ip_input.c:233 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 __netif_receive_skb_one_core net/core/dev.c:5661 [inline] __netif_receive_skb+0x2bf/0x650 net/core/dev.c:5775 process_backlog+0x662/0x15b0 net/core/dev.c:6108 __napi_poll+0xcb/0x490 net/core/dev.c:6772 napi_poll net/core/dev.c:6841 [inline] net_rx_action+0x89b/0x1240 net/core/dev.c:6963 handle_softirqs+0x2c4/0x970 kernel/softirq.c:554 do_softirq+0x11b/0x1e0 kernel/softirq.c:455 </IRQ> <TASK> __local_bh_enable_ip+0x1bb/0x200 kernel/softirq.c:382 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:908 [inline] __dev_queue_xmit+0x1763/0x3e90 net/core/dev.c:4450 dev_queue_xmit include/linux/netdevice.h:3105 [inline] neigh_hh_output include/net/neighbour.h:526 [inline] neigh_output include/net/neighbour.h:540 [inline] ip_finish_output2+0xd41/0x1390 net/ipv4/ip_output.c:235 ip_local_out net/ipv4/ip_output.c:129 [inline] __ip_queue_xmit+0x118c/0x1b80 net/ipv4/ip_output.c:535 __tcp_transmit_skb+0x2544/0x3b30 net/ipv4/tcp_output.c:1466 tcp_rcv_synsent_state_process net/ipv4/tcp_input.c:6542 [inline] tcp_rcv_state_process+0x2c32/0x4570 net/ipv4/tcp_input.c:6729 tcp_v4_do_rcv+0x77d/0xc70 net/ipv4/tcp_ipv4.c:1934 sk_backlog_rcv include/net/sock.h:1111 [inline] __release_sock+0x214/0x350 net/core/sock.c:3004 release_sock+0x61/0x1f0 net/core/sock.c:3558 mptcp_sendmsg_fastopen+0x1ad/0x530 net/mptcp/protocol.c:1733 mptcp_sendmsg+0x1884/0x1b10 net/mptcp/protocol.c:1812 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x1a6/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2597 ___sys_sendmsg net/socket.c:2651 [inline] __sys_sendmmsg+0x3b2/0x740 net/socket.c:2737 __do_sys_sendmmsg net/socket.c:2766 [inline] __se_sys_sendmmsg net/socket.c:2763 [inline] __x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2763 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f04fb13a6b9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 01 1a 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd651f42d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f04fb13a6b9 RDX: 0000000000000001 RSI: 0000000020000d00 RDI: 0000000000000004 RBP: 00007ffd651f4310 R08: 0000000000000001 R09: 0000000000000001 R10: 0000000020000080 R11: 0000000000000246 R12: 00000000000f4240 R13: 00007f04fb187449 R14: 00007ffd651f42f4 R15: 00007ffd651f4300 </TASK> As noted by Cong Wang, the splat is false positive, but the code path leading to the report is an unexpected one: a client is attempting an MPC handshake towards the in-kernel listener created by the in-kernel PM for a port based signal endpoint. Such connection will be never accepted; many of them can make the listener queue full and preventing the creation of MPJ subflow via such listener - its intended role. Explicitly detect this scenario at initial-syn time and drop the incoming MPC request. Fixes: 1729cf1 ("mptcp: create the listening socket for new port") Cc: stable@vger.kernel.org Reported-by: syzbot+f4aacdfef2c6a6529c3e@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=f4aacdfef2c6a6529c3e Cc: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241014-net-mptcp-mpc-port-endp-v2-1-7faea8e6b6ae@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> [ Conflicts in mib.[ch], because commit 6982826 ("mptcp: fallback to TCP after SYN+MPC drops"), and commit 27069e7 ("mptcp: disable active MPTCP in case of blackhole") are linked to new features, not available in this version. Resolving the conflicts is easy, simply adding the new lines declaring the new "endpoint attempt" MIB entry. ] Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the new mode (called as mode#3) to monitor speed and control the PWM. Initialize mode #3 by default (fan tach input enable and PWM mode enable). We can reconfigure again by the pwm_enale setting. Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>

arm:dts:mtjade: Enable I2C4 device access

3fae864

Set BMC_GPIOY2_I2C4_O_EN high to enable access to devices on the I2C4 bus. Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

arm:dts:mtjade: Enable I2C4 device access #3

arm:dts:mtjade: Enable I2C4 device access #3

thangqn-ampere commented Dec 12, 2020

arm:dts:mtjade: Enable I2C4 device access #3

Are you sure you want to change the base?

arm:dts:mtjade: Enable I2C4 device access #3

Conversation

thangqn-ampere commented Dec 12, 2020